• 한국해안·해양공학회논문집
• /
• 제21권2호
• /
• pp.191-195
• /
• 2009

손상된 철근콘크리트 보를 모의하기 위해 사전균열을 발생시킨 후, GFRP Bar와 GSP 매입공법으로 보수하여 피로실험을 수행하였다. 피로실험 결과, 실험보는 피로하중 초기 싸이클에서 대부분의 잔류처짐과 균열이 발생하고 싸이클 수에 따른 이들의 증가율은 미미하였다. 보수보의 정적강도는 보수하지 않은 보에 비해 크게 증가하였지만, 피로강도는 감소하였다. S-N 곡선에서, GFRP Bar 보수보의 피로강도는 정적강도의 58%, GSP 보수보의 피로강도는 52%였다.

• International Journal of Concrete Structures and Materials
• /
• 제9권2호
• /
• pp.159-172
• /
• 2015

Estimation of the residual strength of corroded reinforced concrete beams has been studied from experimental and theoretical perspectives. The former is arduous as it involves casting beams of various sizes, which are then subjected to various degrees of corrosion damage. The latter are static; hence cannot be generalized as new coefficients need to be re-generated for new cases. This calls for dynamic models that are adaptive to new cases and offer efficient generalization capability. Computational intelligence techniques have been applied in Construction Engineering modeling problems. However, these techniques have not been adequately applied to the problem addressed in this paper. This study extends the empirical model proposed by Azad et al. (Mag Concr Res 62(6):405-414, 2010), which considered all the adverse effects of corrosion on steel. We proposed four artificial neural networks (ANN) models to predict the residual flexural strength of corroded RC beams using the same data from Azad et al. (2010). We employed two modes of prediction: through the correction factor ($C_f$) and through the residual strength ($M_{res}$). For each mode, we studied the effect of fixed and random data stratification on the performance of the models. The results of the ANN models were found to be in good agreement with experimental values. When compared with the results of Azad et al. (2010), the ANN model with randomized data stratification gave a $C_f$-based prediction with up to 49 % improvement in correlation coefficient and 92 % error reduction. This confirms the reliability of ANN over the empirical models.

• Steel and Composite Structures
• /
• 제27권4호
• /
• pp.509-523
• /
• 2018

This paper presents experimental results on the residual bond-slip behavior of high strength concrete-filled square steel tube (HSCFST) after elevated temperatures. Three parameters were considered in this test: (a) temperature (i.e., $20^{\circ}C$, $200^{\circ}C$, $400^{\circ}C$, $600^{\circ}C$, $800^{\circ}C$); (b) concrete strength (i.e., C60, C70, C80); (c) anchorage length (i.e., 250 mm, 400 mm). A total of 17 HSCFST specimens were designed for push-out test after elevated temperatures. The load-slip curves at the loading end and free end were obtained, in addition, the distribution of steel tube strain and the bond stress along the anchorage length were analyzed. Test results show that the shape of load-slip curves at loading ends and free ends are similar. With the temperature constantly increasing, the bond strength of HSCFST increases first and then decreases; furthermore, the bond strength of HSCFCT proportionally increases with the anchoring length growing. Additionally, the higher the temperature is, the smaller and lower the bond damage develops. The energy dissipation capacity enhances with the concrete strength rasing, while, decreases with the temperature growing. What is more, the strain and stress of steel tubes are exponentially distributed, and decrease from the free end to loading end. According to experimental findings, constitutive formula of the bond slip of HSCFST experienced elevated temperatures is proposed, which fills well with test data.

• 한국항해항만학회지
• /
• 제33권2호
• /
• pp.119-125
• /
• 2009

The effect of plastic board drains (PBDs)on ground improvement was checked out considering three crucial factors: ground settlement, undrained shear strength, and residual water head. First, the settlement analysis including initial settlement induced by reclamation of sand mat was conducted by back calculation analysis with measured data. Its result showed toot the PBDs used for this site worked well on improving soft ground. Secondly, the undrained shear strength was investigated by laboratory and in-situ tests including unconsolidated-undrained triaxial compression (UU) tests, unconfined compression tests, in-situ vane tests, and cone penetration tests. From the test results, they showed that the undrained shear strength of the improved ground by PBDs was significantly increased as well as the strength increasing ratio especially $10{\sim}15m$ below the ground surface on site. Thirdly, the residual water head measurement from the in situ dissipation test was found the same as the static water head, which indicated primary consolidation was completed and the effect of soil improvement with PBDs can be confirmed.

• 한국해양공학회지
• /
• 제22권2호
• /
• pp.99-105
• /
• 2008

Ultrasonic nanocrystal surface modification (UNSM) is a method to induce severe plastic deformation to a material surface, so that the structure of the material surface becomes a nanocrystal structure from the surface to a certain depth. It improves the mechanical properties, namely hardness, compressive residual stress, and fatigue characteristics. Specimens of SKD61 were tested to verify the effects of the variation of UNSM static load level on fatigue characteristics. The results were as follows: the grain size of SKD61 treated with UNSM became very fine from the material surface to a $100{\mu}m$ depth. The surface hardness of SKD61 was increased up to 37% after UNSM. And fatigue strength at $10^7$ cycles was increased by 8.3, 11.2, and 17.9% respectively, when the static load levels of UNSM were 4, 6, 8 kgf.

• 한국생산제조학회지
• /
• 제5권4호
• /
• pp.53-62
• /
• 1996

Recently, ceramic / metal bonded joints have led to inccreasing use of structural materials such as automobile, heat engine in various industries. In this paper, a method to analyze an interface crack under both residual stresses and applied loading was proposed. and some results of boundary element method(BEM) analysis Were presented, Fracture thoughness tests of ceramic/metals bonded joints with an interface crack Were carried out, and the stress intensity factors of these joints Ware analyzed by BEM. Also crack propagtion direction was simulated numerically by using BEM. Crack propagation angle was able to easily determine based on the maximum stress concept. The prediction of fracture strength by the fracture thoughness of the ceramics/metals bonded joints was proposed.

• 한국지반공학회논문집
• /
• 제15권5호
• /
• pp.125-139
• /
• 1999

풍화잔적토는 불교란 시료를 채취하기가 곤란하기 때문에 전단강도를 산정하는데 있어서 어려움을 겪고 있다 본 연구에서는 직접 전단시험용 불교란 시료를 용이하게 채취하기 위해서 슈 장착 직접 전단상자를 개발하였으며, 성공적으로 불교란 시료를 채취할 수 있었다. 채취된 분교란 시료의 직접 전단시험을 통해서 포화조건에 따른 전단강도의 변화를 규명하였다. 그리고 교란에 따른 풍화잔적토의 전단거동을 규명하기 위해서 정적시료 성형장치를 제작하였고, 자연함수비 상태에서는 교란에 따른 강도저하가 나타나지만, 수침시에는 강도가 유사함을 확인하였다. 불교란 시료에 대해서 직접전단시험과 삼축압축시험시의 강도를 비교한 결과, 직접 전단시험시 수침시료의 강도가 삼축압축시험의 결과와 유사한 경향을 나타내었다. 그리고 대상 붕괴사면에 대한 역해석을 수행한 결과, 슈 장착 직접 전단상자를 이용하면 풍화잔적토 사면에서의 전단강도 산정이 가능하리라고 판단되었다.

• 대한조선학회논문집
• /
• 제57권4호
• /
• pp.182-190
• /
• 2020

This study reports a series of drop impact tests performed to generate denting damages on stiffened plates and their residual ultimate strength tests under axial compression. The models were fabricated of general structural steel, and each model has six longitudinal stiffeners and two transverse frames. Among six fabricated models, four were damaged, and two were left intact for reference. To investigate the effects of collision velocity and impact location on the extent of damage, the drop height and the impact location were changed in each impact test. After performing the collision tests, the ultimate axial compression tests were conducted to investigate the residual strengths of the damaged stiffened plates. Finite element analyses were also carried out using a commercial package Abaqus/Explicit. The material properties obtained from a quasi-static tensile tests were used, and the strain-rate sensitivity was considered. After importing the collision simulation results, the ultimate strength calculations were carried out and their results were compared with the test data for the validation of the finite element analysis method.

• 비파괴검사학회지
• /
• 제17권2호
• /
• pp.81-88
• /
• 1997

탄소섬유강화복합재료(CFRP) 적층판에 비교적 낮은 에너지의 충격을 주어, 충격에 의해서 손상된 적층판을 사용하여 인장강도, 파괴 인성 및 AE 신호 특성에 미치는 충격 손상의 영향에 대하여 검토하였다. 충격손상재의 인장강도, 파괴 인성 및 AE-event count는 충격 속도와 박리 면적의 증가에 따라서 감소함을 알 수 있었다. 그리고 충격시험시에 발생한 박리 면적은 충격 속도와 비례하였다. 또한 적층 방법에 따른 손상재의 강도비와 파괴 인성비가 달라짐이 확인되어 복합재료의 내충격 설계시 손상량과 손상재의 파괴 인성 및 강도에 대한 정량적 평가를 AE 신호로부터 해석할 수 있음이 확인되었다.

• 한국재료학회지
• /
• 제4권2호
• /
• pp.219-226
• /
• 1994

반복회수에 대한 하중-변형률 선도로부터 구산 잔류변형률의 비교 결과에서 피로하중하의 GFRP관의 강성은 GFRP관의 유리섬유의 적층수가 클수록 크게 나타났으며, 이러한 현상은 피로파괴 직전까지 나타났다. 아울러 본 피로실험 결과를 회귀분석하여 구한 S-N선도에 의하면 정적극한강도 백분율에 대한 피로강도는 GFRP관의 유리섬유 적층수가 증가할수록 증가하였으며, 유리섬유의 적층수가 15, 25, 35층인 GFRP관의 반복회수 200만회에 대한 피로강도는 정적극한강도는 각각 약 75.2%, 79.5%, 84.2%로 나타났다.