• The Korean Journal of Pesticide Science
• /
• v.17 no.2
• /
• pp.126-132
• /
• 2013

The objectives of this study were to provide the basic data of the residue of deltamethrin in the stream water. Deltamethrin was treated on side of Ban-Suk stream and Juk-Dong ditch for hygienic purpose by air spray. The drift concentration of deltamethrin was investigated with different wind speed condition on Ban-Suk stream (A), and the change of residue with time course on Juck-dong ford (B). Also we found the residual change of deltamethrin until 48 hour in Yu-Seong stream confluence (C) where two streams join. Maximum residues of A were $0.17{\mu}g/L$ (5 min, 200 m) at strong wind speed and $4.42{\mu}g/L$ (0 min, 25 m) at moderate wind speed according to different wind velocity. Residues of B were $0.15{\sim}0.26{\mu}g/L$ (0~480 min) after spraying, and decreased to a non-detected level after 720 min. Residues of C were $0.15{\mu}g/L$ (0 min), $0.11{\mu}g/L$ (1 min) and $0.10{\mu}g/L$ (12 hr) after spraying, and no residues were detected in any other samples. From these results, it is concluded that deltamethrin residues in water should be rapidly diluted into stream water and affected negligible toxic effect to stream ecosystem.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.4
• /
• pp.234-241
• /
• 2000

Organic farming (OF) is regarded as alternative farming types against general farming system for sustainable agriculture, recently. However, there is little information on effects of OF on soil properties and watershed condition. In order to determine the effects of OF on soil properties, 36, 10 and 8 sites of organic farming (OF) fields of plastic film houses, paddy and orchard were selected in the national scale, respectively, to evaluate their chemical properties and phosphorus distributing characteristics. The average organic matter (OM) contents in organic farming fields were with $44g\;kg^{-1}$ in plastic film houses, $26g\;kg^{-1}$ in paddies and $39g\;kg^{-1}$ in orchard soils higher than the average OM contents in conventional farming (CF) soils. Available phosphates were accumulated to 986 in plastic film house soils and $754mg\;kg^{-1}$ in orchard soils, respectively, over the optimum range. Furthermore, total P (T-P) reached to $2.973mg\;kg^{-1}$ in plastic film houses and $2303mg\;kg^{-1}$ in orchards in OF soils. It could be attained by applying repeatedly low N/P ratio of manure-based compost. In two types of soils inorganic P was dominant with the ratio of 62~80% of T-P, and then residual and organic Ps followed. However. residual-P was dominant in paddy soils with the rate of 50% of T-P. Fractionation of soil extractable P showed that Ca-P was dominant with about $1,330mg\;kg^{-1}$ in upland soils in OF fields, which is affected by high soil pH of over 6.0. However. Fe-P of extractable P was dominant in paddy soils. Water-soluble P was very high with 65 and $26mg\;kg^{-1}$ in plastic film house and orchard soils in OF. From this results. OF regarded as an environment-friendly farming system may cause serious soil deterioration by accumulated phosphorus and may also cause water pollution.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.34 no.2
• /
• pp.37-45
• /
• 2022

A simplified model using the lifetime distribution has been presented to estimate the Mean Residual Life (MRL) of rubble-mound breakwaters, which is not like a stochastic process model based on time-dependent history data to the cumulative damage progress of rubble-mound breakwaters. The parameters involved in the lifetime distribution can be easily estimated by using the upper and lower limits of lifetime and their likelihood that made a judgement by several experts taking account of the initial design lifetime, the past sequences of loads, and others. The simplified model presented in this paper has been applied to the rubble-mound breakwater with TTP armor layer. Wiener Process (WP)-based stochastic model also has been applied together with Monte-Carlo Simulation (MCS) technique to the breakwater of the same condition having time-dependent cumulative damage to TTP armor layer. From the comparison of lifetime distribution obtained from each models including Mean Time To Failure (MTTF), it has found that the lifetime distributions of rubble-mound breakwater can be very satisfactorily fitted by log-normal distribution for all types of cumulative damage progresses, such as exponential, linear, and logarithmic deterioration which are feasible in the real situations. Finally, the MRL of rubble-mound breakwaters estimated by the simplified model presented in this paper have been compared with those by WP stochastic process. It can be shown that results of the presented simplified model have been identical with those of WP stochastic process until any ages in the range of MTT F regardless of the deterioration types. However, a little of differences have been seen at the ages in the neighborhood of MTTF, specially, for the linear and logarithmic deterioration of cumulative damages. For the accurate estimation of MRL of harbor structures, it may be desirable that the stochastic processes should be used to consider properly time-dependent uncertainties of damage deterioration. Nevertheless, the simplified model presented in this paper can be useful in the building of the MRL-based preventive maintenance planning for several kinds of harbor structures, because of which is not needed time-dependent history data about the damage deterioration of structures as mentioned above.

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.251-255
• /
• 2014

In this study, we optimized dissolution the dissolution conditions of porous amorphous powder to have high specific surface area. Porous metallic glass(MG) granules were fabricated by selective phase dissolution, in which brass is removed from a composite powder consisting of MG and 40 vol.% brass. Dissolution was achieved through various concentrations of $H_2SO_4$ and $HNO_3$, with $HNO_3$ proving to have the faster reaction kinetics. Porous powders were analyzed by differential scanning calorimetry to observe crystallization behavior. The Microstructure of milled powder and dissolved powder was analyzed by scanning electron microscope. To check for residual in the dissolved powder after dissolution, energy dispersive X-ray spectroscory and elemental mapping was conducted. It was confirmed that the MG/brass composite powder dissolved in 10% $HNO_3$ produced a porous MG granule with a relatively high specific surface area of $19.60m^2/g$. This proved to be the optimum dissolution condition in which both a porous internal granule structure and amorphous phase were maintained. Consequently, porous MG granules were effectively fabricated and applications of such structures can be expanded.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.5
• /
• pp.50-56
• /
• 2014

A technique based on the finite element method (FEM) is used in the simulation of metal cutting process. This offers the advantages of the prediction of the cutting force, the stresses, the temperature, the tool wear, and optimization of the cutting condition, the tool shape and the residual stress of the surface. However, the accuracy and reliability of prediction depend on the flow stress of the workpiece. There are various models which describe the relationship between the flow stress and the strain. The Johnson-Cook model is a well-known material model capable of doing this. Low-alloy steel is developed for a dry storage container for used nuclear fuel. Related to this, a process analysis of the plastic machining capability is necessary. For a plastic processing analysis of machining or forging, there are five parameters that must be input into the Johnson-Cook model in this paper. These are (1) the determination of the strain-hardening modulus and the strain hardening exponent through a room-temperature tensile test, (2) the determination of the thermal softening exponent through a high-temperature tensile test, (3) the determination of the cutting forces through an orthogonal cutting test at various cutting speeds, (4) the determination of the strain-rate hardening modulus comparing the orthogonal cutting test results with FEM results. (5) Finally, to validate the Johnson-Cook material parameters, a comparison of the room-temperature tensile test result with a quasi-static simulation using LS-Dyna is necessary.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.11
• /
• pp.874-882
• /
• 2003

The condition assessment of engineering systems has increased in importance because the manpower needed to operate and supervise various plants has been reduced. Especially, induction motors are at the core of most engineering processes, and there is an indispensable need to monitor their health and performance. So detection and diagnosis of motor faults is a base to improve efficiency of the industrial plant. In this paper, a model-based fault detection system is developed for induction motors, using steady state vibration signals. Early various fault detection systems using vibration signals are a trivial method and those methods are prone to have missed fault or false alarms. The suggested motor fault detection system was developed using a model-based reference value. The stationary signal had been extracted from the non-stationary signal using a data segmentation method. The signal processing method applied in this research is FFT. A reference model with spectra signal is developed and then the residuals of the vibration signal are generated. The ratio of RMS values of vibration residuals is proposed as a fault indicator for detecting faults. The developed fault detection system is tested on 800 hp motor and it is shown to be effective for detecting faults in the air-gap eccentricities and broken rotor bars. The suggested system is shown to be effective for reducing missed faults and false alarms. Moreover, the suggested system has advantages in the automation of fault detection algorithms in a random signal system, and the reference model is not complicated.

• Journal of the Korean Dietetic Association
• /
• v.8 no.2
• /
• pp.175-184
• /
• 2002

This study is to investigate consequent nutrient intake status, influence of body mass index(BMI), and fat distribution on the silk amino peptide(SAP) and dietary fiber supplementation. During 2 months of this research (January to March, 2002), 45 women aged 20yr – 30yr (average age 24.6yr) were selected as subjects. Nutrient intake was investigated by questionnaire, 24-hr recall method. Antropometric assessments of the subjects were investigated by SBIA method(Segmental bioimpedance assay, In body 3.0). The results are as follows: mean body weight 57.7kg, mean body height 161.9cm mean BMI 22.0, and mean food habit score was 8.47. Defecation frequency was increased by dietary fiber supplementation. Frequency of pain during defecation was significantly decreased by dietary fiber supplementation (p<0.01). Feeling of residual feces was significantly improved by dietary fiber supplementation(p<0.001). Status of energy and carbohydrate intakes significantly decreased after dietary fiber supplementation(P<0.05). Body fat and WHR(waist hip ratio) significantly decreased after dietary fiber supplementation(P<0.001), and percent body fat was decreased by dietary fiber supplementation, significantly(P<0.05). Above results of this study show that dietary fiber-added routine diet improves defecation condition, and lessens body fat, percent body fat without losing body muscle. Especially, declination of abdominal fat and WHR were notable. That meant decreased risk factor.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.5
• /
• pp.7-24
• /
• 2008

Masan-Jinhae Bay, in Korea, is known for its frequent algal bloom outbreaks. This study was conducted in order to examine the environmental characteristics of the area, with the aim of identifying indicators that could be used to speculate about future algal blooms. The water temperatures and salinities in Haengam Bay, one of the small inner bays within Jinhae, appeared to re relatively higher than those in Masan and Jinhae bays, across most seasons. Furthermore, stratification begins to develop in all three regions from spring to summer as a result of the local heating effects and an increase in the efficient from the surrounding land. As a result, anoxic conditions appear near the bottom layer of the bay, leading to the deterioration of water quality, which has been identified as one of the causes of bloom outbreaks. Compared to Haengam and Jinhae bays, concentrations of DIN and DIP were remarkably higher in Masan Bay. However, the mean ratio of DIN to DIP was 3.3$\sim$13.6 in all three regions throughout the year, suggesting that nitrogen can function as a growth-limiting factor for phytoplankton. The results of mathematical models showed that cumulative organic pollutants may be a trigger for direct algal bloom occurrences, since residual tidal currents appeared to be less than $3\;cm\;\cdot\;s^{-1}$. Furthermore, computed DO concentrations in the four small inner bays of Jinhae during the summer appeared to be $3\;cm\;\cdot\;l^{-1}$ indicating a hypoxic state. Likewise, computed Chl-a concentrations turned out to be more than $0.01\;mg\;\cdot\;l^{-1}$, indicating eutrophication across most seasons. Based on the overall results, Masan-Jinhae Bay appeared to possess a very high potential for algal bloom outbreaks at anytime during the year.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.1
• /
• pp.93-99
• /
• 2005

Up to date, the life extension of industrial plant structures has been strongly required in the field of iron-manufacturing company, atomic or power generation company and so on. Fault monitoring, maintenance of aging structural components, safety assessment and residual life prediction may be recognized as typical and/or practical methods in terms of life extension methods. Based on the construction of damage scenario, precise analysis method and development of the risk or reliability assessment, a number of studies have been carried out in this viewpoint. In conjunction with the finite element analysis technique, a practical procedure for the safety assessment of iron-manufacturing plant structures was developed in this paper with a particular interest in furnace. By virtue of the detailed finite element analyses for blust furnace under an operational condition, the validity of the proposed procedure for safety assessment was presented.

• Tuberculosis and Respiratory Diseases
• /
• v.72 no.2
• /
• pp.218-222
• /
• 2012

Pulmonary artery intimal sarcoma is a rare tumor with no characteristic symptoms. It is frequently misdiagnosed as pulmonary embolism. We report a case of pulmonary artery intimal sarcoma in a 48-year-old man with dyspnea, cough and blood-tinged sputum. He was initially suspected and treated as a pulmonary embolism. Computed tomography of the chest showed filling defects occupying the entire luminal diameter of the right and left pulmonary artery as well as extraluminal extension of the intraluminal mass. Surgical resection of the tumor confirmed pulmonary artery intimal sarcoma. After surgery, he received 8 cycles of combined chemotherapy consisting of doxorubicin and ifosfamide. After 8 cycles, Computed tomography of the chest showed interval regression of the residual tumor. Radiotherapy was done as total 6,000 cGy for 5 weeks, following the 8th chemotherapy. The patient's condition was successfully stabilized with chemotherapy and radiotherapy.