• Steel and Composite Structures
• /
• v.38 no.4
• /
• pp.365-380
• /
• 2021

Although traditional steel-concrete composite beams have excellent structural characteristics, it cannot meet the requirement of quick assembly and repair in the engineering. This paper presents a study on static behavior of bolt connected steel-concrete composite beam without post-cast zone. A three-dimensional finite element model was developed with its accuracy and reliability validated by available experimental results. The analysis results show that in the normal service stage, the bolt is basically in the state of unidirectional stress with the loss of pretightening can be ignored. Parametric studies are presented to quantify the effects of the post-cast zone, size and position of splicing gap on the behavior of the beam. Based on the studies, suggested size of gap and installation order were proposed. It is also confirmed that optimized concrete slab in mid-span can reduce the requirement of construction accuracy.

• Journal of Positioning, Navigation, and Timing
• /
• v.12 no.4
• /
• pp.379-389
• /
• 2023

According to the Korea Urban Air Mobility (K-UAM) Concept of Operation (ConOps), the Global Navigation Satellite System (GNSS) is recommended as the primary navigation system and the performance specification will be implemented considering the standard of Performance Based Navigation (PBN). However, by taking into account the characteristics of an urban environment and the concurrent operations of multiple UAM aircraft, the current PBN standards for civil aviation seem difficult to be directly applied to an UAM aircraft. Therefore, by referring to technical documents published in the literature, this paper examines the feasibility of applying the proposed performance requirements to K-UAM, which follows the recommendation of navigation performance requirements for K-UAM. In accordance with the UAM ConOps, the UAM aircraft is anticipated to maintain low altitude during approach and landing phases. Subsequently, the navigation performance degradation could occur in the urban environment, and the primary degradation factor is identified as multipath error. For this reason, to ensure the safety and reliability of the K-UAM aircraft, it is necessary to analyze the degree of performance degradation related to the urban environment and then propose an alternative aid to enhance the navigation performance. To this end, the aim of this paper is to model the multipath effects of the GNSS in an urban environment and to carry out the simulation studies using the real GNSS datasets. Finally, the initial navigation performance requirement is proposed based on the results of the numerical simulation for the K-UAM.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.308-313
• /
• 2016

Modern systems have become more and more complex due to the ever-increasing user requirements and rapid advance of technology. As such, the frequency of accidents due to system design errors or failure has been increasing. When the damage incurred by accidents to human beings or property is serious, the underlying systems are referred to as safety-critical systems. The development of such systems requires special efforts to ensure the safety of the human beings operating them. To cope with such a requirement, in this paper an approach is employed in which we consider safety starting from the conceptual design phase of the systems. Specifically, a systems design method that can detect functional failure is proposed by utilizing meta-models and M&S methods. To accomplish this, the safety design data from international safety standards are first extracted and also a meta-model is generated using SysML (systems modeling language). Then, a SysML-based system design method is proposed based on the use of the developed meta-model. We also discuss how the safety requirements can be created and verified using a simulation method. Finally, through a case study in automotive design, it is demonstrated that the detection of a functional failure and the verification of a safety requirement can be accomplished using the SysML-based M&S method. This study indicates that the use of meta-models can be useful for collecting and managing safety data and that the meta-model based M&S method can make it possible to satisfy the system requirements by reducing the design errors.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.31 no.6_2
• /
• pp.611-623
• /
• 2013

Point cloud data (i.e., LiDAR; Light Detection and Ranging) collected by Airborne Laser Scanner (ALS) system is one of the major sources for surface reconstruction including DEM generation, topographic mapping and object modeling. Recently, demand and requirement of the accurate and realistic Digital Building Model (DBM) increase for geospatial platforms and spatial data infrastructure. The main issues in the object modeling such as building and city modeling are efficiency of the methodology and quality of the final products. Efficiency and quality are associated with automation and accuracy, respectively. However, these two factors are often opposite each other. This paper aims to introduce correction scheme of incorrectly determined Model Key Points (MKPs) regardless of the segmentation method. Planimetric and height locations of the MKPs were refined by surface patch fitting based on the Least-Squares Solution (LESS). The proposed methods were applied to the synthetic and real LiDAR data. Finally, the results were analyzed by comparing adjusted MKPs with the true building model data.

• 한국HCI학회:학술대회논문집
• /
• 2009.02a
• /
• pp.68-73
• /
• 2009

As various haptic algorithms and haptic equipments have developed, the computer simulation includes the haptic simulation. Basically, the haptic simulation requires very fast refresh rate approximately 1000 Hz. The traditional haptic simulations have satisfied that requirement by simplifying the target model. In soft body simulation, simplifying the deformation is not good because the visual feedback is important. Separating haptic model from deformable model can be solution of that problem. However, the user may feel a subtle distiction because the relationship between two models are not clear. In this paper, we propose the hybrid model to manipulate haptic rendering and deformation and define the relationship between two models.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.466-474
• /
• 2016

The model tests results for the original lines of an 10000TEU container vessel show that the delivered power is higher and could not satisfy the requirement of energy saving effects and design targets. In this paper, the lines optimization of the 10,000 twin-skeg container vessel was carried out by parametric modeling and CFD simulations. At first, the CFD methods for twin-skeg hull form were validated by the comparison with the experimental results. Then more than one hundred parameters were adopted for the establishment of the fully parametric model. Based on the parametric model of the twin-skeg container vessel, the preliminary optimization was carried out by tight coupling of FRIENDSHIP-FRAMEWORK with potential flow of SHIPFLOW. Then several important parameters related to the after part of twin-skeg vessel were investigated by viscous flow computation. The final optimized variant PM11, which the total resistance was reduced by about 8.3% in model scale, is obtained within the constraints of general arrangement. And the model tests for variant PM11 was carried out in CSSRC, which shows that the resistance of optimized variant PM11 is decreased by about 8.6%.

• Journal of Integrative Natural Science
• /
• v.4 no.2
• /
• pp.91-98
• /
• 2011

Quantitative structure-activity relationships (QSAR) have been applied for two decades in the development of relationships between physicochemical properties of chemical substances and their biological activities to obtain a reliable statistical model for prediction of the activities of new chemical entities. The fundamental principle underlying the QSAR is that the structural difference is responsible for the variations in biological activities of the compounds. In this work, we developed 3D-QSAR model for a series of 5-Lipoxygenase inhibitors, utilizing comparative molecular field analysis (CoMFA) and Topomer CoMFA methodologies. Our developed models addressed superiority of Topomer CoMFA over CoMFA. The CoMFA model was obtained with $q^2$=0.593, $r^2$=0.939, $Q^2$=0.334 with 6 optimum number of components (ONC). Higher statistical results were obtained with the Topomer CoMFA model ($q^2$=0.819, $r^2$=0.947, ONC=5). Further robustness of developed models was checked with the ANOVA test and it shows F=113 for CoMFA and F=162.4 for Topomer CoMFA model. Contour map analysis indicated that the more requirement of electrostatic parameter for improved potency.

• Electronics and Telecommunications Trends
• /
• v.32 no.6
• /
• pp.105-115
• /
• 2017

This paper describes a project - based quality management model that identifies development technologies and codes while at the same time verifying the ability to implement processes that are essential in R & D projects. In order to verify the process implemented in the R & D project implementation, there are review, checking points, and evaluating methods the process performance levels for five processes such as defining requirements which is the beginning stage of system development, testing process which is the completion stage of system development, and project management and peer review process for project management and support in the proposed project-based quality management model. For development technology and code validation, the model included the documented test cases for each requirement by the developer in the requirements definition stage, debugging and testing in the design and implementation stages, static analysis and open source licence verification procedure, and system environment. After applying the model in SW development R&D project for evaluating the process performance, and verifying the development technology and the code, the developers responded that the improvement in the development technique and the code, and upgrade of process performance level for project are more than 10%.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.4
• /
• pp.9-16
• /
• 2011

Modern systems become more complex and the demand for systems safety goes up sharply. Thus, the proper handling of the safety requirements in the systems design is getting greatly increased attention these days. Hazard analysis has been one of the active areas of research in connection with systems safety. In this paper, we study a subject on how the hazard analysis results can be incorporated in the systems design. To this end we set up a goal on how to systematically generate safety requirements that should reflect hazard analysis results and be implemented in the systems design and development. To do so, we first review the process for systems design and suggest the associated Model. Then the process and results of hazard analysis are analyzed and Modeled particularly with emphasis on the safety data. The resulting data Model incorporating both the hazard analysis and system life cycle is used in the generation of safety requirements. Based on the developed data Model, the generation of the requirements, the construction of requirements DB, and the change management later on is demonstrated through the use of a computer-aided software tool.

• The KIPS Transactions:PartD
• /
• v.15D no.6
• /
• pp.815-824
• /
• 2008

Embedded system is applied in various fields and must equip system to respond market's requirement which is changing fast. Products that do not equip such fast construction system will have become sterilization. Construction system for Time-To-Market is reusability system or framework that have reused existent product and produce new product. Because embedded system is being based on hardware, amendment is not available easily, but can change system softly using segment of software. Therefore, in this paper, suggest meta-model of reusability framework that can change embedded software. Meta model of this paper suggests dynamic meta-model to design functional flow of reusability framework.