• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.10
• /
• pp.667-676
• /
• 2015

Working displacement variation by elastic deformation of active Gurney flap which was operated on high frequency was observed. Flap-wise natural frequency was lower than mode analysis result and hinge boundary condition was identified to be the cause through the simple modal test. Design modification for increasing natural frequency was conducted for minimizing the elastic deformation at maximum 35 Hz operating condition which was design requirement condition. Brass bushing was applied instead of rotating bearing for gap minimization and Gurney flap design modification was conducted to increase of the flap-wise natural frequency. Design modification effect was validated by natural frequency comparison with mode analysis result and modal test result of design modification model.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.5
• /
• pp.1951-1972
• /
• 2018

Wi-Fi Access Point (AP) optimization approaches are used in indoor positioning systems for signal coverage enhancement, as well as positioning precision improvement. Although the huge power consumption of the AP optimization forms a serious problem due to the signal coverage requirement for large-scale indoor environment, the conventional approaches treat the problem of power consumption independent from the design of indoor positioning systems. This paper proposes a new Fast Water-filling algorithm Group Power Constraint (FWA-GPC) based Wi-Fi AP optimization approach for indoor positioning in which the power consumed by the AP optimization is significantly considered. This paper has three contributions. First, it is not restricted to conventional concept of one AP for one candidate AP location, but considered spare APs once the active APs break off. Second, it utilizes the concept of water-filling model from adaptive channel power allocation to calculate the number of APs for each candidate AP location by maximizing the location fingerprint discrimination. Third, it uses a fast version, namely Fast Water-filling algorithm, to search for the optimal solution efficiently. The experimental results conducted in two typical indoor Wi-Fi environments prove that the proposed FWA-GPC performs better than the conventional AP optimization approaches.

• Journal of Energy Engineering
• /
• v.8 no.4
• /
• pp.533-539
• /
• 1999

Integration methods of a Gas Turbine and a Air Separation Unit have a potential to improve plant performance and cost of IFCC. Several studies on those integrations schemes were carried out. Then some of the methods were accually in commercial plants. Thus paper reviewed the integration schemes of a Gas Turbine and a Air Separation Unit. In order to compare the plant performance of IGCC with each scheme, simulation model was developed for IGCC power cycle with Texaco Quench gasification process. The simulation results showed that the thermal efficiency of the plant was appeared to be the best when all of the air consumption required for Air Separation Unit was supplied from the Gas Turbine and the net plant power output was maximized when 75% of the total ASU an requirement was supplied from Gas Turbine.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.03a
• /
• pp.50-58
• /
• 2003

We have developed a locally variable time-step scheme matching with discontinuous grids in the flute-difference method for the efficient simulation of seismic wave propagation. The first-order velocity-stress formulations are used to obtain the spatial derivatives using finite-difference operators on a staggered grid. A three-times coarser grid in the high-velocity region compared with the grid in the low-velocity region is used to avoid spatial oversampling. Temporal steps corresponding to the spatial sampling ratio between both regions are determined based on proper stability criteria. The wavefield in the margin of the region with smaller time-step are linearly interpolated in time using the values calculated in the region with larger one. The accuracy of the proposed scheme is tested through comparisons with analytic solutions and conventional finite-difference scheme with constant grid spacing and time step. The use of the locally variable time-step scheme with discontinuous grids results in remarkable saving of the computation time and memory requirement with dependency of the efficiency on the simulation model. This implies that ground motion for a realistic velocity structures including near-surface sediments can be modeled to high frequency (several Hz) without requiring severe computer memory

• Earthquakes and Structures
• /
• v.7 no.3
• /
• pp.251-269
• /
• 2014

To investigate the seismic performance and to obtain quantitative parameters for the requirement of performance-based bridge seismic design approach, 12 reinforced concrete (RC) hollow rectangular bridge column specimens were tested under constant axial load and cyclic bending. Parametric study is carried out on axial load ratio, aspect ratio, longitudinal reinforcement ratio and transverse reinforcement ratio. The damage states of these column specimens were related to engineering limit states to determine the quantitative criteria of performance-based bridge seismic design. The hysteretic behavior of bridge column specimens was simulated based on the fiber model in OpenSees program and the results of the force-displacement hysteretic curves were well agreed with the experimental results. The damage states of residual cracking, cover spalling, and core crushing could be well related to engineering limit states, such as longitudinal tensile strains of reinforcement or compressive strains of concrete, etc. using cumulative probability curves. The ductility coefficient varying from 3.71 to 8.29, and the equivalent viscous damping ratio varying from 0.19 to 0.31 could meet the requirements of seismic design.

• Wind and Structures
• /
• v.16 no.2
• /
• pp.157-178
• /
• 2013

Output-only modal parameter identification is based on the assumption that external forces on a linear structure are white noise. However, harmonic excitations are also often present in real structural vibrations. In particular, it has been realized that the use of forced acceleration responses without knowledge of external forces can pose a problem in the modal parameter identification, because an external force is imparted to its impulse acceleration response function. This paper provides a three-stage identification procedure as a solution to the problem of harmonic and white noise excitations in the acceleration responses of a linear dynamic system. This procedure combines the uses of the mode indicator function, the complex mode indication function, the enhanced frequency response function, an iterative rational fraction polynomial method and mode shape inspection for the correlation-related functions of the force-embedded acceleration responses. The procedure is verified via numerical simulation of a five-floor shear building and a two-dimensional frame and also applied to ambient vibration data of a large-span roof structure. Results show that the modal parameters of these dynamic systems can be satisfactorily identified under the requirement of wide separation between vibration modes and harmonic excitations.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1736-1746
• /
• 2008

Because present road traffic reaches to the limitation of its faculty, Korean tilting train was developed to find the solution by increasing the speed of rail road. A tilting train can run on a curved rail at high speed so it improves a speed of a rail transit without constructing a new line. Only minimum modification is necessary for a existing line. According to above requirement, Korean tilting train was developed in 2007 and the try run has been executing since April, 2007 in order to validate its safety and reliability in a service lines. And this test and estimation will be completed in 2009. After completing a try run, main parts of tilting train will be studied again to commercialize and localize including a bogie and its commercial model design will be finalized by 2012. In order to achieve the development target as mentioned above, the study have been done to improve the bogie system. As the first step to design commercialized bogie system, measurements from the try run and a dynamic analysis were used to find problems of present bogie system well. So this project is performed to decide what parts of the bogie should be modified in basis of this result.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.7
• /
• pp.630-638
• /
• 2004

Liquid desiccant dehumidification systems have the ability to provide efficient humidity and temperature control while saving the electrical energy requirement for air conditioning as compared to a conventional system. The dehumidifier and the regenerator form the heart of this system. The latent part of the cooling load is overcome using liquid desiccant. The model regenerator has been designed to study the absorption characteristic of the aqueous triethylene glycol (TEG) solution which is in the flow range from 20 to 50 LPM. Also, this system designed that was able to change the height of the regenerator and dehumidifier. Because the effect of performance have different result according the height. The effect of performance factors of the regenerator with inlet solution flow rate, air flow rate, solution concentration, solution temperature, brine temperature, air temperature and inlet air relative humidity have been analyzed. Data obtained are useful for design guidance and performance analysis of the hybrid air conditioning system.

• Journal of the Korea Society of Computer and Information
• /
• v.7 no.1
• /
• pp.137-146
• /
• 2002

The benefit of TPL(Third-party Logistics) is reduction of transportation time, accuracy, improved expertise knowledge and access to logistics information system, improved operational efficiency, improved customer service, ability to focus in core business and greater flexibility. On the contrary, the defect of TPL is loss of control, unreliable promise of the enterprise (provider),inability to respond to logistics system requirement, lack of understanding of the user business goals . This thesis aims to suggest the optimal strategic to improve the logistics system and to satisfy the customer needs and also aims to suggest the TPL method to strengthen the TPL companies. And strategic plan Total (enterprise-TPL-customer) Logistics Information System(TLSI) of TPL operation. focused on transportation service and mechanism to use GPS model.

• Journal of Soil and Groundwater Environment
• /
• v.25 no.2_spc
• /
• pp.55-69
• /
• 2020

Permeability-analyzing methods commonly involve small-scale drilling, such as pumping or slug test, but it is difficult to identify overall distribution of permeability of the entire target sites due to high cost and time requirement. Spectral induced polarization (SIP) method is known to be capable of providing distributions of both the porosity and the pore size, the two major parameters determining permeability of the porous medium. The relationship between SIP variables and permeability has been studied to identify the hydrological characteristics of target sites. Kozeny-Carman formula has been improved through many experiments to better predict fluid permeability with electrical properties. In this work, the permeability prediction techniques based on SIP data were presented in accordance with the hydrogeological and electrical characteristics of a porous medium. Following the summary of the techniques, various models and related laboratory experiments were analyzed and examined. In addition, the field applicability of the prediction model was evaluated by field case analysis.