• 대한기계학회논문집B
• /
• 제21권10호
• /
• pp.1371-1379
• /
• 1997

The high pressure drop is frequently required in the by-pass line of the pump or of the heat exchanger in power plants. However, cavitation produced by a high pressure drop could damage the pipe and pump blades. Conical orifices are adopted to reduce cavitation due to high pressure drop. The discharge coefficients of conical orifice plates were measured by weighing method in the standard water flow system. The discharge coefficients were larger when the ratios of thickness of orifice edge to throat diameter were larger. The noise generated from a conical orifice due to cavitation was measured with a sound level meter and a hydrophone. With increasing the bore diameter of the orifice, the sound pressure level or the noise level due to cavitation became higher. The noise level was suddenly increased at the inception of cavitation.

• 한국소음진동공학회논문집
• /
• 제20권3호
• /
• pp.249-256
• /
• 2010

This paper presents performance analysis of a quarter-vehicle magneto-rheological(MR) suspension system with respect to different tire pressure. As a first step, MR damper is designed and manufactured based on the optimized damping force levels and mechanical dimensions required for a commercial mid-sized passenger vehicle. After experimentally evaluating dynamic characteristics of the manufactured MR damper, the quarter-vehicle MR suspension system consisting of sprung mass, spring, tire and the MR damper is constructed in order to investigate the ride comfort. After deriving the equations of the motion for the proposed quarter-vehicle MR suspension system, vertical tire stiffness with respect to different tire pressure is experimentally identified. The skyhook controller is then implemented for the realization of quarter-vehicle MR suspension system. Ride comfort characteristics such as vertical acceleration RMS and weighted RMS of sprung mass are evaluated under various road conditions.

• 한국환경과학회지
• /
• 제28권10호
• /
• pp.887-898
• /
• 2019

Rehabilitation work is required to increase well productivity, which decreases with the elapsed time of pumping owing to the clogging of the water well. Clogging causes not only a reduction in the well productivity but also a deterioration of the water quality. For unclogging and rehabilitating wells, several techniques are used such as brushing, air surging, surge blocks, and gas impulse. In this study, the high-pressure air impulse technique, which effectively and economically rehabilitates wells, was applied to a riverbank filtration site in Korea for the same objective. At most of the wells, the hydraulic parameters (transmissivity, storage coefficient, and specific capacity) were increased by the application of the high-pressure air impulse technique. The well loss change values also indicate an increase in the hydraulic parameters by the air impulse implementation. Thus, the high-pressure air impulse technique can be efficiently and economically applied to water and riverbank filtration wells for rehabilitating the decreased productivity.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.39-39
• /
• 1999

The KSTAR (Korea Superconducting Tokamak Advanced Research) tokamak is a nuclear fusion experimental device for a long pulse/steady-state plasma operation, adopting fully superconducting magnets. In accordance with completion of the basic design of the torus vacuum vessel and the enclosing cryostat, the vacuum pumping and gas fueling basic design has been developed to fulfil the physics requirements. The ultra-high vacuum pumping and sophisticated gas fueling system of the machine is essential to achieve such roles for optimized plasma performance and operation. Recently the vacuum exhaust system using dedicated pumping ports for the vacuum vessel and cryostat has been modified to meet more reliable and successful performance of the KSTAR[Fig. 1].In order to achieve the required base pressure of 5 x 10-9 torr, the total impurity load to the vessel internal is limited to ~5 x 10-5 torr-1/x, while the cryostat base pressure is kept as ~5 x 105 torr to mitigate the thermal load applied to the superconducting magnets. Each KSTAR fueling system will be separately capable of fueling gas at a rate of 50 torr-1/x, consistent with the given pumping throughput. In order to initiate a plasma discharge in KSTAR, the vacuum vessel is filled to a gas pressure of few 10-6 to few 10-4 torr, and additional gas injection is required to maintain and increase the plasma density during the course of the discharge period.

• 한국지반공학회지:지반
• /
• 제12권2호
• /
• pp.19-32
• /
• 1996

시간영역의 지진 가속도-시간 이력을 주파수 영역의 courier 진폭-주파수 이력으로 변화시키는 Trifunac의 경험적 모델을 기초로 하여 지진 관측소에서 측정된 임의 규모의 실제 지진기록들을 필요한 규모의 지진기록으로 유사화시키는 지진 확대 (scaling) 기법을 제안하였다. 또한, 지진 규모(M) 5.6의 지진기록을 이용하여 지진 규모(M) 8.0의 유사지진을 작성하여 동적 재하 시험 장치에 적용가능하도록 하였다. 지진 확대 (scaling) 기법은 MMI(modified mercalli intensity), 지진기록 부지의 조건,진앙거리,지진 가속도 성분의 방향, 해석의 신뢰도 등을 고려할 수 있으며, 다양한 지진 기록들에 적용가능하였다.유사지진은 수평방향의 성분들만을 고려하여 작성되었다. 압력토조내에 설치된 모형인장말뚝과 개단압출말뚝에 대한 유사지진 진동에 의한 동적 말뚝재하시험이 가능하였다. 정적 말뚝재하시험시 인장말뚝과 압축말뚝의 거동은 매우 상이하였는데, 인장말뚝은 2~3회의 급작스런 미끄러짐 변위를 수반하였다. 또한, 유사 지진 진동중 인장말뚝과 개단압축말뚝의 거동특성은 매우 상이하였으며, 지지력 감소특성도 크게 달랐다.

• Composites Research
• /
• 제31권1호
• /
• pp.12-16
• /
• 2018

복합소재와 금형강 간에는 열팽창계수의 차이로 인하여 성형 과정 중의 온도 구배에 따라 다른 열팽창길이를 갖는다. 따라서 금형 내에 복합소재를 삽입하여 성형을 하는 경우 복합소재의 표면에 작용하는 압력이 소재의 업체에서 추천하는 성형 압력을 유지하는지를 확인할 필요성이 있다. 본 연구에서는 온도의 차이에 따른 복합소재와 금형 사이의 압력을 유한요소해석법을 사용하여 예측하였으며 열팽창에 따른 금형의 길이를 측정함으로써 해석의 정확성을 검증하였다. 각 온도에서의 해석과 실험값의 차이로써 매우 근사한 값을 얻을 수 있었으며, 틈새 예측 값의 목표치인 ${\pm}0.05mm$ 안에 들어오는 것을 확인하였다. 이를 통하여 복합소재에 작용하는 압력을 추정한 해석값이 신뢰할 수준임을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제25권1호
• /
• pp.15-22
• /
• 1997

The effectiveness of presteaming for improving CCA treatability on refractory Japanese larch heartwood was investigated in this study. Presteaming was effective on improving treatability, and the extent of improvement was dependent on moisture contents of wood specimen and steaming conditions. Green wood showed higher average value in both preservative retention and penetration than dry wood, and steaming under pressure conditions also had higher treatability than steaming at atmospheric conditions. The degree of improvement for treatability was increased with the extension of steaming period. Treatability of dry wood pres teamed under pressure conditions more than 6 hours and green wood for 3 hours was similar to that enhanced by conventional incising. Presteaming green wood under pressure conditions more than 6 hours was more effective than conventional incising in improvement of CCA treatability, and resultant treatability satisfied a minimum value required for CCA-treated wood for being used at the regions of hazard class H3 and H4. In addition, an improvement of treatability by presteaming was due to an increase in permeability resulted from the degradation of hemicelluloses within aspirated pit membrane and cell wall, not the removal of extractives from pit membrane. The reduction in strength, measured as longitudinal compressive strength, due to pres teaming was related with the degradation of hemicelluloses, and was increased as steaming conditions were severe. The degree of strength reduction associated with presteaming treatment to obtain required treatability could be quantified from the relatively good relation between the increase in treatability and the decrease in strength.

• 펄프종이기술
• /
• 제37권5호통권113호
• /
• pp.70-77
• /
• 2005

The development of printable Hanji is regarded as an important work to create a new demand of Hanji in information-oriented era. Hanji has rougher surface, huger absorption of ink and lower optical properties and printabilities than common printing papers. Improving those shortcomings of Hanji is required to be printable Hanji. Sizing and calendering have known as a way to make properties of paper good. Accordingly, this research was performed to find out useful sizing agents for reforming its drawbacks. Four sizing agents (CMC, com starch, PVA, AKD) were used in this research. The optical properties and the printabilities of sized Hanji were tested. The obtained results were as follows. Based on concentration, each sizing agent was prepared. These were CMC(0.5, 1, $1.5\%$), corn starch(1, 2, $3\%$), PVA(1, 5, $10\%$), AKD(0.5, 0.1, $0.15\%$) respectively. After sizing, we performed calendering treatment with pressure of 0.5, $1\;kgf/cm^2$. All the sizing agents and calendering treatment improved the properties of Hanji to some extent. Particularly, com starch was good for gloss. In case of printability, $1\%$ AKD with $1\;kgf/cm^2$ was recommendable for typography ink density, $3\%$ com starch with $0.5\;kgf/cm^2$, inkjet ink density, $2\%$ com starch with $0.5\;kgf/cm^2$, inkjet ink girth. PVA and AKD without calendering were counter-effective agents for inkjet ink density. Printable Hanji is required to have not only better surface strength enough to appear non-picking, higher ink density and lower show-through than base paper but also the lowest ink girth in comparison with base paper. When referring to them, efficient sizing agents were regarded as $0.1\%$ AKD with $1\;kgf/cm^2$, calender pressure, for typography printing and $2\%$ com starch with $0.5\;kgf/cm^2$, calender pressure, for inkjet printing.

• 한국정밀공학회지
• /
• 제29권12호
• /
• pp.1331-1339
• /
• 2012

Safety valve used in LNG/LNG-FPSO ships is a high value valve, and it plays an important role in maintaining a fixed level of pressure by emitting LNG gas out of pipes in LNG piping system under the cryogenic and high-pressure condition when the pressure of the system connected with the LNG storage tank and pipes reaches over the set pressure. The structural stability is required for the inner pressure and thermal load because of the cryogenic and high-pressure condition, and a reliability of the safety valve is necessary for impact and deformation by opening the valve. But, the safety valve, which plays a key role for a safety of the transport and storage system, is depended on imports for over 90%, and in domestic production, the design of the valve is performed on the basis of experiences of the works without quantitative analysis for the inner operation characteristics and structural stability of the valve. In this study, impact velocity is calculated by theoretical analysis for obtaining the structural stability of the guide according to the impact load by opening the valve. The shape of the guide and the diaphragm for satisfying the structural stability are suggested and verified by using a thermal-structural analysis.

• 대한한방내과학회지
• /
• 제36권3호
• /
• pp.419-426
• /
• 2015

Objectives This study reports three cases of pressure ulcer treated with Hwangryunhaedok-tang pharmacopuncture. Methods Three patients with pressure ulcers were treated by Hwangryunhaedok-tang pharmacopuncture and Jaungo at the Oriental Medicine Hospital of Daejeon University. Hwangryunhaedok-tang pharmacopuncture and Jaungo was administrated once a day with simple dressing. Thereafter, we observed the pressure ulcers macroscopically. Results and Conclusions After 3 weeks, wound sizes were reduced and tissue regeneration was accelerated. In conclusion, Hwangryunhaedok-tang pharmacopuncture and Jaungo are effective to treat pressure ulcers, but more studies will be required to validate its use in pressure ulcers.