• 한국재료학회지
• /
• 제19권8호
• /
• pp.407-411
• /
• 2009

Reflection properties, such as specular reflection and diffuse reflection, are very important optical properties for the reflector, which has high reflectance in the display and architecture industry. Calcite is lowcost, nontoxic, and stable over a wide temperature range. Therefore, it is one of the most widely using fillers in many industries and has some advantages over titania as a filler to improve reflectance. However, optical properties, especially those of ceramic-filled composites, have not been analyzed. We studied the reflectance of calcite composites with their surface roughness. The reflectance of the composites was determined using a UV-visible spectrometer. The surface morphology and the micro-structure of the composites were investigated by atomic force microscope. The reflectance of the composites was improved by increasing the content of calcite in the calcite-frit composite. The reflectance is related with the surface roughness in the composites. However, the reflectance depends on the calcite contents in materials with similar surface roughness.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.377-381
• /
• 2006

A seismic survey for gas hydrate have performed over the East sea by the KIGAM since 1997. General indicator of gas hydrate in seismic data is commonly inferred from the BSR(Bottom Simulating Reflector) that occurred parallel to the sea floor, amplitude decrease at the top of the BSR, amplitude blanking at the bottom of the BSR, decrease of the interval velocity and the reflection phase reversal at the BSR. In this paper we had analyzed optimum parameters of the field data to detect the 9as hydrate. Shot delay correction is applied 95ms, spherical divergence correction is applied velocity library 3, bandpass filter is applied 25-30-115-120Hz deconvolution operator length is applied 60ms, lag is 6ms and accurate velocity analysis NMO correction, stack is performed. Geobit 2.11.0 developed by the KIGAM was used for all data processing. Processing results say that the BSR occurred parallel to the sea floor were shown at 3,150m/s of two way travel time from the sea floor through shot point 5,000-5,610, and identified the interval velocity decrease around BSR and the reflection phase reversal corresponding to the reflection at the sea floor.

• 한국재료학회지
• /
• 제23권3호
• /
• pp.194-198
• /
• 2013

In this paper, we studied a p-type reflector based on indium tin oxide (ITO) for vertical-type ultraviolet light-emitting diodes (UV LEDs). We investigated the reflectance properties with different deposition methods. An ITO layer with a thickness of 50 nm was deposited by two different methods, sputtering and e-beam evaporation. From the measurement of the optical reflection, we obtained 70% reflectance at a wavelength of 382 nm by means of sputtering, while only 30% reflectance resulted when using the e-beam evaporation method. Also, the light output power of a $1mm{\times}1mm$ vertical chip created with the sputtering method recorded a twofold increase over a chip created with e-beam evaporation method. From the measurement of the root mean square (RMS), we obtained a RMS value 1.3 nm for the ITO layer using the sputtering method, while this value was 5.6 nm for the ITO layer when using the e-beam evaporation method. These decreases in the reflectance and light output power when using the e-beam evaporation method are thought to stem from the rough surface morphology of the ITO layer, which leads to diffused reflection and the absorption of light. However, the turn-on voltage and operation voltage of the two samples showed identical results of 2.42 V and 3.5 V, respectively. Given these results, we conclude that the two ITO layers created by different deposition methods showed no differences in the electric properties of the ohmic contact and series resistance.

• 한국통신학회논문지
• /
• 제38B권9호
• /
• pp.744-750
• /
• 2013

본 논문에서는 메타물질 특성을 구현하기 위하여 고임피던스 표면을 갖는 인공자기도체(AMC) 구조를 제안하였다. 설계한 AMC 구조는 3.2GHz에 적용하는 것을 목표로 하였으며, 특성 분석을 위해 다중의 AMC 구조를 일정하게 배열한 반사판으로 제작 및 측정하였다. AMC 반사판의 표면에 형성되는 높은 임피던스로 인하여 반사 특성이 좋아지고, 간섭 및 시스템의 크기를 줄이며, 안테나의 성능을 증가시킨다. 제안된 구조는 설계된 AMC와 접지면을 잇는 via hole을 사용하지 않고, 유전체의 두께와 유전율, 구조의 특성을 이용하여 고임피던스를 구현하였다. 기존의 연구된 via hole이 없는 구조와 비교하여 대역폭이 약 150% 증가하였다. 또한, 금속(PEC) 반사판과 동일한 반사특성을 보이는 대신, 안테나와 반사판 간의 거리를 ${\lambda}/10$까지 줄일 수 있다. 실험을 통하여 안테나와의 거리가 약 10mm 지점에서 방사 특성이 3dB 증가한 것을 확인하였다. 설계된 반사판은 반사거리가 작아 휴대용 무선통신기기의 내부에 삽입이 가능하며, 안테나의 효율을 증가시키고, 후방 방사를 차폐함으로써 전자파인체흡수율을 94% 이상 획기적으로 감소시킬 수 있다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권7호
• /
• pp.308-314
• /
• 2005

The 2 GHz film bulk acoustic wave resonator(FBAR), one of the most necessary device of the next generation mobile communication system, consisted of solidly mounted resonator(SMR) structure using Brags reflector, was researched in this paper The FBAR applied SiO$_{2}$ and W had large difference of the acoustic impedance to reflector Al to electrode and ZnO to piezoelectric layer. Specially, the FBAR applied the two-step deposition method to improve the c-axis orientation and increase reproducibility of the fabrication device had good performance. The electrical properties of plasma such as impedance, resistance, reactance, $V_{pp},\;I{pp}$, VSWR and phase difference of voltage and current, was analyzed and measured by RF sensor with the variable experiment process factors such as gas ratio, RF power and base vacuum level about concerning the thickness, c-axis orientation, adhesion and roughness. The FBAR device about the optimum condition resulted reflection loss(S$_{11}$) of -17 dB, resonance frequency of 1.93 GHz, electric-mechanical coefficient(k$_{eff}$) of 2.38 $\%$ and Qualify factor of 580. It was seen better qualify than the common dielectric filter at present and expected on business to the filter device of 2 GHz bandwidth with the MMIC technology.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.507-510
• /
• 2007

Piston cores retrieved from the western Ulleung Basin, East Sea were analyzed to examine the potential for hydrocarbon generation and to determine the hydrocarbon indicators. 2D multi-channel reflection seismic and Chirp data were also investigated for mapping and characterizing the geophysical hydrocarbon indicators such as BSR (bottom simulating reflector), blank zone, pock-mark etc. High organic carbon contents and sedimentation rates that suggest good condition for hydrocarbon generation. High pressure and low temperature condition, and high residual hydrocarbon concentrations are favor the formation of natural gas hydrate. In the piston cores, cracks generally oriented to bedding may indicate the gas expansion. The seismic data show several BSRs that are associated with natural gas hydrates and underlying free gas. A number of vertical to sub-vertical blank zones were well identified in the seismic sections. They often show the seismic pull-up structures, probably indicating the presence of high velocity hydrates. Numerous pockmarks were also observed in the Chirp profiles. They may indicate the presence of free gas below the hydrate stability zone as well.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2017년도 춘계학술대회
• /
• pp.63-64
• /
• 2017

본 연구에서는 UHF RFID(915 MHz)와 GPS(1.575 GHz) 이중대역용 코플래너 도파관으로 급전되는 소형 준-야기 안테나 설계 방법에 대해 연구하였다. 제안된 안테나는 다이폴, 반사기, 도파기 등 3소자로 구성되며, 소형화를 위해 다이폴과 반사기는 끝부분을 접고, 도파기는 다이폴에 근접한 영역에 두고, 밸런은 안테나에 내장형으로 설계하였다. 시뮬레이션을 통해 제안된 안테나를 UHF RFID와 GPS 시스템에서 사용이 가능하도록 0.8 mm 두께의 FR4 기판에 설계하고, 반사계수, 이득, 복사패턴 등의 안테나 특성을 확인하였다.

• 조명전기설비학회논문지
• /
• 제29권5호
• /
• pp.26-33
• /
• 2015

Secondary optical system designed for LED bulb which emits light in all directions was simulated with Energy Star standards. Components of the optical system were LED light source, the cover of the LED bulb and reflector which is to confirm the diffuser plate and LightTools software was used to design the illumination optics. The main points of the secondary optical system design are the location of the LED light source, the shape of the LED bulb cover, the location of the reflection plate, and the scattering properties of the diffusing plate. Mechanism of the LED bulb is that the light emitted from the light source move on to the backward after reflected by the coated light cover from the inside and then the reflected light is scattered by the diffuser plate. The LED bulb was designed to satisfy the standard light distribution and color specifications of the Energy Star(IES LM-79-08).

• Journal of Mechanical Science and Technology
• /
• 제17권8호
• /
• pp.1185-1195
• /
• 2003

Heat losses from the receivers of a dish-type solar energy collecting system at the Korea Institute of Energy Research (KIER) are numerically investigated. It is assumed that a number of flat square mirrors are arranged on the parabolic dish structure to serve as a reflector. Two different types of receivers, which have conical and dome shapes, are considered for the system, and several modes of heat losses from the receivers are thoroughly studied. Using the Stine and McDonald model convective heat loss from a receiver is estimated. The Net Radiation Method is used to calculate the radiation heat transfer rate by emission from the inside surface of the cavity receiver to the environment. The Monte-Carlo Method is used to predict the radiation heat transfer rate from the reflector to the receiver. Tracing the photons generated, the reflection loss from the receivers can be estimated. The radiative heat flux distribution produced by a multifaceted parabolic concentrator on the focal plane is estimated using the cone optics method. Also, the solar radiation spillage around the aperture is calculated. Based on the results of the analysis, the performances of two different receivers with multifaceted parabolic solar energy collectors are evaluated.

• 한국인터넷방송통신학회논문지
• /
• 제20권5호
• /
• pp.157-162
• /
• 2020

기존의 태양광발전장치 중에서 반사판을 갖춘 장치는 태양에너지(일사량)를 태양광 모듈 표면에 집중적으로 입사되는 방식이지만 태양광 모듈을 통해 다시 반사되어 손실되는 태양에너지(일사량)는 고려되지 않는 구조로 되어있다. 또한, 태양광 모듈 주위에 반사판을 설치하여 발전량을 높이는 방안이 제시되고 있지만, 이는 다른 태양광 모듈의 음영에 따른 발전 저하에 영향을 주고 있다. 따라서 이러한 문제점을 개선하고자 본 논문에서는 1) 음영에 따른 태양광 모듈의 발전에 영향을 주지 않으면서 2) 태양광 모듈에서 반사되어 손실되는 태양에너지(일사량)를 회전하는 반사판을 이용하여 태양광 모듈에 다시 입사되는 방법을 연구 및 제안한다. 따라서 손실된 태양에너지(일사량)의 무수한 반사 각도에 따른 태양에너지를 재활용할 수 있는 방법을 통해 태양에너지(일사량)에 대한 손실을 최소화, 동일 일사량에 대한 발전량을 최대화하므로 태양광발전장치의 발전량을 증가시킬 수 있다.