• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.415-423
• /
• 1996

Hydrogen reduction technique was used to form the nickel layer onto alumina powders in nickel sulfate solutions. The reduction rate and precipitation states of nickel ions were investigated at various experimental conditions such as hydrogen pressure, temperature, $PdCl_{2}$ addition, particle size, and so on. Uniformly nickel coated alumina composite powders were obtained at such condition as reduction temperature of $165^{\circ}C$, hydrogen pressure of 300 psi, and $PdCl_{2}$ amount of $2\;mg/\ell$.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.33 no.4
• /
• pp.397-400
• /
• 2007

In an open reduction of the mandibular angle fracture, it is crucial to approximate each fracture segment as closer as possible for the reduction of the healing period. In this case report, we proposed a new technique for the mandibular angle fracture. This was designed to minimize the gap between two separated segments using mini-implants and surgical wires. Mini-implants were placed around the fracture line, followed by wire ligation to minimize the fracture gap. And then internal fixation was easily employed with plates and screws. The advantages of this technique were reduced time for operation, the promotion of healing, rapid functional recovery, and few complications.

• Journal of the Korea Society for Simulation
• /
• v.10 no.2
• /
• pp.61-74
• /
• 2001

The reliability evaluation of the large scale network becomes very complicate according to the growing size of network. Moreover if the reliability is not constant but follows probability distribution function, it is almost impossible to compute them in theory. This paper studies the network evaluation methods in order to overcome such difficulties. For this an efficient path set algorithm which seeks the path set connecting the start and terminal nodes efficiently is developed. Also, various variance reduction techniques are applied to compute the system reliability to enhance the simulation performance. As a numerical example, a large scale network is given. The comparisons of the path set algorithm and the variance reduction techniques are discussed.

• Journal of Environmental Science International
• /
• v.24 no.8
• /
• pp.1065-1073
• /
• 2015

Urbanization can be significantly affected the hydrologic cycle by increasing flood discharge and heat flux. In order to mitigate these modifications in urban areas, Low Impact Development (LID) technique has been designed and applied in Korea. In order to estimate runoff reduction rate using SWMM LID model, the characteristics of five LID techniques was firstly analyzed for water balance. Vegetated swale and green roof were not reduce flood discharge nor infiltration amount. On the other hand, porous pavement and infiltration trench were captured by infiltration function. The flood reduction rate with LID is substantially affected by their structures and properties, e.g., the percentage of the area installed with LID components and the percentage of the drainage area of the LID components.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1315-1323
• /
• 2014

Although the power density in Double Stator Switched Reluctance Motor (DSSRM) has been improved, the torque ripple is still very high. So, it is important to reduce the torque ripple for specific applications such as Electric Vehicles (EVs). In This paper, an effective rotor shaping optimization technique for torque ripple reduction of DSSRM is presented. This method leads to the lower torque pulsation without significant reduction in the average torque. The method is based on shape optimization of the rotor using Finite Element Method and Taguchi's optimization method for rotor reshaping for redistribution of the flux so that the phase inductance profile has smoother variation as the rotor poles move into alignment with excited stator poles. To check on new design robustness, mechanical analysis was used to evaluate structural conformity against local electromagnetic forces which cause vibration and deformation. The results show that this shape optimization technique has profound effect on the torque ripple reduction.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.3
• /
• pp.18-27
• /
• 1996

The feasibility of using stress-wave technique in the transverse direction for the assessment of early stages of decay was investigated using compression test specimens having different annual ring orientations subjected to decay by Tyromyces palustris for various time intervals. Decay detection, quantitative assessment of decay, and the prediction of residual strength of decayed wood with less than five percent weight loss can be feasible using stress-wave parameters (wave velocity, wave impedance, and stress-wave elasticity) and their percent reduction due to decay, measured by stress-wave technique in the transverse direction. The use of stress-wave technique in the transverse direction for the application of this technique to structural members in service is desirable, when considering the easiness of attachment of accelerometers of stress-wave measuring device on the surface of members and also accurate detection of localized decayed areas. In stress-wave technique in the transverse direction, stress-wave parameters measured were different according to the angles between wave propagation path and annual ring, due to the anisotropy of wood structure. Therefore, it is recommended to use percent reduction in stress-wave parameters instead of stress-wave parameters. This evaluation method using percent reduction in stress-wave parameters is ideal when it is impossible to observe annual ring orientation on the transverse surface of wood.

• Archives of Plastic Surgery
• /
• v.38 no.3
• /
• pp.300-308
• /
• 2011

Purpose: The goal of reduction mammaplasty is breast with natural cone shape, minimizing scars, well-placed and sensate nipple-areolar area and maintaining breast physiology. In order to satisfy that goal, variable reduction mammaplasty methods are performed, however, two methods such as vertical reduction method and inverted T-scar method are currently most used. We compared indications and advantages of the two methods and set up useful guidlines. Methods: For 15 years from 1995 to 2010, we experienced 84 patients (162 breasts). We performed vertical reduction method as Lejour's superior pedicle technique (45 patients) and inverted T-scar method as Goldwyn's inferior dermal flap technique (39 patients). We evaluated the result of the operation comparing patient's age, amount of resected tissue, complications and post-operative scars of the two methods. Results: The mean age was 36 years and the vertical reduction group was 3 years younger than inverted T-scar group. The mean breast tissue resection amount per one breast, inverted T-scar group (712 gm) was lagger than vertical reduction group (395 gm). Conclusion: There is no ideal method for reduction mammaplasty until now. However, we suggest that guide line, the vertical reduction method is effective for minimal and moderate macromastia in young and middle aged women and inverted T-scar method is appropriate for severe macromastia with ptosis in elderly women. Recently, all procedures tried shorter and smaller scar on the vertical line as small I, J or L shape scar, and inframammary fold as short inverted T-scar.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.2
• /
• pp.180-185
• /
• 2008

A new method for relative error continuous and discrete time model order reduction is proposed. The reduction technique is based on two recently developed methods, namely frequency domain balanced truncation within a frequency bound and inner-outer factorization techniques. The proposed method is of interest for practical model order reduction because in this context it shows to keep the accuracy of the approximation as high as possible without sacrificing the computational efficiency. Numerical results show the accuracy and efficiency enhancement of the method.

• Journal of Korean Academy of Nursing
• /
• v.16 no.3
• /
• pp.123-130
• /
• 1986

This Study is aimed at showing the effect of relaxation technique on reduction of anxiety of nursing students in the first clinical practice. The samples of this research were eighty fresh-man students of Dong San Junior College of Nursing. Of them thirty-eight were experimental group and remaining forty-two were control group. This study has been conducted from October 14 to 22, 1985. Subjects in all two groups had measured their trait anxiety, after then, the researcher carried out Byun's relaxation technique with experimental group every other day After the experimental period, subjects in all two groups had measured their state anxiety. The tools of this study were two kinds: Spielberg, Gorsuch & Lushene's STAI, and Byun's relaxation technique. To test the statistical difference in the subjects' trait anxiety, score of lecture in pre-clinical practice and score of practice pre-clinical practice, t-test was performed. To verify the hypotheses, ANCOVA was performed. Results of this study were as follows: The main hypothesis that the nursing students who use relaxation technique will have less degree of anxiety in the first clinical practice than the nursing students who don't use relaxation technique was accepted (P<.005). Conclusively, the researcher thinks that it is necessary that nursing students were prepared with relaxation technique to reduce anxiety in their first clinical practice.

• Journal of Korean Neurosurgical Society
• /
• v.30 no.sup1
• /
• pp.159-164
• /
• 2001

Reduction cranioplasty is one of the treatment modality among many treatment options for macrocephaly with hydrocephalus. The most previous techniques of reduction cranioplasty have some disadvantages such as difficult airway maintenance, pressure sore due to modified prone position, severe venous infarct due to obstruction of venous blood flow and large amount of bleeding from the dissection of superior sagittal sinus to obtain bone fragment needed. A 28-month-old girl had extreme macrocephaly. She couldn't control head rotation and keep sitting position. The operation was performed at supine position with adequate exposure of entire calvarium and the hinge was made in occipital bone fragment that covered posterior part of superior sagittal sinus. Bleeding volume and the other complications were decreased and acceptable reduction was achieved with this method.