• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.4
• /
• pp.98-104
• /
• 2023

The feasibility of an efficient process proposed for Cu-Cu flip-chip bonding was evaluated by forming a porous Cu layer on Cu pillar and conducting thermo-compression sinter-bonding after the infiltration of a reducing agent. The porous Cu layers on Cu pillars were manufactured through a three-step process of Zn plating-heat treatment-Zn selective etching. The average thickness of the formed porous Cu layer was approximately 2.3 ㎛. The flip-chip bonding was accomplished after infiltrating reducing solvent into porous Cu layer and pre-heating, and the layers were finally conducted into sintered joints through thermo-compression. With reduction behavior of Cu oxides and suppression of additional oxidation by the solvent, the porous Cu layer densified to thickness of approximately 1.1 ㎛ during the thermo-compression, and the Cu-Cu flip-chip bonding was eventually completed. As a result, a shear strength of approximately 11.2 MPa could be achieved after the bonding for 5 min under a pressure of 10 MPa at 300 ℃ in air. Because that was a result of partial bonding by only about 50% of the pillars, it was anticipated that a shear strength of 20 MPa or more could easily be obtained if all the pillars were induced to bond through process optimization.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.10
• /
• pp.844-854
• /
• 2017

The Expansion-Deflection(E-D) nozzle is a nozzle that has a performance gain through the altitude compensation effect by changing the effective area within the nozzle according to the altitude. An E-D nozzle has been known to reduce the length of the nozzle and achieve the payload gain of the launch vehicle. Due to the potential advantages of an E-D nozzle, related research has been carried out in the United Kingdom, Germany, Australia and Europe etc. In the UK, the flow characteristics of the E-D nozzle and the performance comparison with the dual-bell nozzle which is altitude compensation nozzle were studied. In order to understand the transition characteristics of the E-D nozzle in DLR, the transition characteristics according to the nozzle pressure ratio change were analyzed. In Europe, numerical study using the E-D nozzle concept on upper stage of the launch vehicle Ariane 5 ESC-B was carried out to confirm the possibility of payload gain according to the nozzle length reduction. In this paper, research trends of an E-D nozzle performed outside the country are classified and analyzed according to their characteristics and utilized as basic data of E-D nozzle research in the future.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.83-90
• /
• 2006

This paper investigates experimentally the fire resistance performance and spatting resistance of high performance reinforced concrete column member subjected to fire containing polypropylene fiber(PP fiber) and cellulose fiber(CL fiber). An increase in PP fiber and CL fiber contents, respectively resulted in a reduction of fluidity due to fiber ball effect. Air content is constant with m increase in fiber content. Compressive strength reached beyond 50 MPa. Based on fire resistance test, severe failure occurred with control concrete specimen, which caused exposure of reinforcing bar. No spall occurred with specimen containing PP fiber. This is due to the discharge of internal vapour pressure. Use of CL fiber superior to control concrete in the side of spatting resistance, localized failure at comer of specimen was observed. Corner of specimen had deeper neutralization than surface of specimen. Specimen containing PP fiber had the least damaged area due to spatting. Neutralization depth ranged between 6 and 8 mm Residual compressive strength of specimen containing PP fiber maintained 40%, which is larger than control concrete with 20% of residual strength. Specimen containing CL fiber had 25% or residual strength.

• Applied Biological Chemistry
• /
• v.46 no.2
• /
• pp.134-139
• /
• 2003

To establish the fertilization condition to increase the productivity of Chasanthemum boreale M. with high quality, the effects of three nutrients (N, P, K) on the yields and the effective components were investigated in the pot scale. NPK was applied by chemical fertilizers with $(N-P_2O_5,-K_2O=250-160-160\;kg/ha)$ as a main treatment, and NP $(N-P_2O_5,-K_2O=250-160-160\;kg/ha)$, NK $(N-K_2O =250-160\;kg/ha)$, and PK $(P_2O_5K_2O=160-160\;kg/ha)$ treatments were settled as comparison. Dry yields of C. boreale M. was increased significantly to 4 fold higher by nitrogen. Nitrogen increased apparently plant growth and inorganic nutrient uptake. In the flower, which is most useful and edible part as a herbal medicine, main amino acids were glutamic acid and aspartic acids, and the total content was increased significantly by three elements of application. In addition, the content of cumambrin A, which is known to have the effect of blood-pressure reduction, was increased source to 6.2 times by nitrogen higher than that in PK treatment. Potassium was more effective in biosynthesis of cumambrin A than phosphorus, but the biological pathway was not clear, still.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.8-13
• /
• 2018

Nitrogen oxides (NOx) have recently been very influential in the generation of ultrafine dust, which is of great social interest in terms of improving the atmospheric environment. Nitrogen oxides are generated mainly by the reaction of nitrogen and oxygen in air in a combustion gas atmosphere of high temperature in a combustion apparatus such as thermal power generation. Recently, research has been conducted on the combustion that recirculates the exhaust gas to the cylindrical burner by using a piping using a Coanda nozzle. In this study, three types of burners were carried out through computational fluid analysis. Case 1 burner with the outlet of the combustion gas to the right, Case 2 burner with both sides as gas exit, Case 3 burner with left side gas exit. The pressure, flow, temperature, combustion reaction rate and distribution characteristics of nitrogen oxides were compared and analyzed. The combustion reaction occurred in Case 1 and Case 2 burner in the right direction with combustion gas recirculation inlet and Case 3 burner in the vicinity of mixed gas inlet. The temperature at the outlet was about $100^{\circ}C$ lower than that of the other burners as the Case 2 burner was exhausted to both sides. The NOx concentration of Case 1 burner at the exit was about 20 times larger than that of the other burners. From the present study, it could be seen that it is effective for the NOx reduction to exhaust the exhaust gas to both side gas exits or to exhaust the exhaust gas to the opposite direction of inlet of recirculation gas.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.2
• /
• pp.202-209
• /
• 1998

A three-dimensional numerical method based on the Green's integral equation is developed to predict the motion response and drift force in waves for the ocean monitoring facilities. In this method, we use source and doublet distribution, and triangular and rectangular eliments. To eliminate the irregular frequency phenomenon, the method of improved integral equation is applied and the time-mean drift force is calculated by the method of direct pressure integration over the body surface. To conform the validity of the present numerical method, some calculations for the floating sphere are performed and it is shown that the present method provides sufficiently reliable results. As a calculation example for the real facilities, the motion response and the drift force of the vertical cylinder type ocean monitoring buoy with 2.6 m diameter and 3,77 m draft are calculated and discussed. The obtained results of motion response can be used to determine the shape and dimension of the buoy to reduce the motion response, and other data such as the effect of motion reduction due to a damper can be predictable through these motion calculations. Also, the calculation results of drift force can be used in the design procedure of mooring system to predict the maximum wave load acting on the mooring system. The present method has, in principle, no restriction in the application to the arbitrary shape facilities. So, this method can be a robust tool for the design, installation, and operation of various kinds of the floating-type ocean monitoring facilities.

• Archives of Plastic Surgery
• /
• v.38 no.1
• /
• pp.7-14
• /
• 2011

Purpose: Many patients have fear for surgery owing to the injection of lidocaine and the possible pain in the course of the operation. To resolve such a problem the cases to do plastic surgery with monitored anesthetic care are increasing, in which something like sedatives is injected into vein without endotracheal intubation and under voluntary respiration, but the usage is now under the controversy. Methods: There were 25 patients who had surgery with local anesthesia, and another 25 patients who had surgery with monitored anesthetic care which belongs to ASA class 1 and 2 from January to April, 2009. Their anesthesia records were collected and surveys were given before and after the surgery and the surgery staff recorded OAA/S during the surgery. The postoperative surveys included the awakening during the surgery, pain, anxiety, and the degree of patient's satisfaction through visual analogue scale to identify the difference between the two methods. Results: The OAA/S results according to time lapse show that it is possible to lead a fast effective sedation and recovery with monitored anesthetic care, and monitored anesthetic care enhances both surgeon's convenience level and patient's satisfaction level, and reduces awakening, pain, and anxiety, compared to local anesthesia. Conclusion: The current paper shows about the plastic surgery, particularly the outpatient surgery, when monitored anesthetic care method is applied, it could gain a fast sedation and recovery or an effective sedation of patients. The method also has some affirmative effects in regard with surgeon's convenience and the patients' satisfaction degree and the reduction of their awakening, pain, and anxiety. With careful and adequate watch on the measures about vital signs like electrocardiogram, the degree of oxygen saturation, and blood pressure, it could clinically be very useful.

• Membrane Journal
• /
• v.21 no.4
• /
• pp.367-376
• /
• 2011

Huge amount of $CH_4$ mixtures has been emitted from landfills and organic wastes via anaerobic digestion. The recovery of high purity $CH_4$ from these gases has two merits: reduction of green house gases and production of renewable fuels. Membrane technology based on polymeric materials can be used in this application. In this study, asymmetric gas separation hollow fiber membranes were fabricated to develop the membrane-based bio-gas purification process. Polyethersulfone (PES) was chosen as a polymer materials because of high $CO_2$ permeability of 3.4 barrer and $CO_2/CH_4$ selectivity of 50[1]. Acetone was used as a non-solvent additive because of its unique swelling power for PES and highly volatile character. The prepared PES hollow fiber showed excellent separation properties: 36 GPU of $CO_2$ permeance and 46 of $CO_2/CH_4$ selectivity at optimized preparation conditions: 9wt% acetone content, 10cm air-gap and 4wt% PDMS coating processes. With the PES hollow fiber membranes developed, mixed $CO_2/CH_4$ test was done by changing various operating conditions such as pressures and feed compositions to meet the highest recovery of CH4 with 95% purity. High $CH_4$ recovery of 58 wt% was observed at 10 atm feed pressure for the 50 vol% of $CO_2$ in $CO_2/CH_4$ mixture.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.33-43
• /
• 2014

Recently, the case to construct the structure on the soft clayey ground has increased and in order to the reduction of the cost of construction and maintenance on the social infrastructure facilities we have been trying to improve the soft clayey ground using the existing methods such as the pre-loading method and the vertical drain method. Like this, when various ground improvement methods are applied on the soft clayey ground, a long-term consolidation settlement will be key issue due to low permeability coefficient of cohesive soil. According to existing research results that relate to the consolidation settlement, the loading periods for existing the standard consolidation test (Oedometer test) to obtain the consolidation parameters are needed for minimum ten days or more. Therefore, in this study, the standard consolidation test (24 hours step-loading) and constant strain rate consolidation test changed by strain rate was performed using the remolded marine clay on Gwangyang bay composed of a soft clayey ground of the south-west coast. From the laboratory test results, the characteristics of compression, strain-effective stress relations by constant strain rate and the variation characteristic of the pore water pressure by different of loading speed and the relation between consolidation parameters and constant strain rate are compared and analyzed.

• Journal of the Korean Institute of Gas
• /
• v.23 no.1
• /
• pp.27-35
• /
• 2019

In order to solve the global warming and reduce greenhouse gas emissions, $CO_2$ capture technology was developed by applying oxy-fuel combustion. But there has been such a problem that its economic efficiency is low due to the high price of oxygen gases. ASU is known to be most suitable method to produce large quantity of oxygen, to reduce the oxygen production cost, the efficiency of ASU need to be improved. To improve the efficiency of ASU, exergy analysis can be used. The exergy analysis provides the information of used energy in the process, the location and size of exergy destruction. In this study, the exergy analysis was used for process developing and optimization of large scale ASU. The process simulation of ASU was conducted, the results were used to calculate the exergy. As a result, to reduce the exergy loss in the cold box of ASU, a lower operating pressure process was suggested. It was confirmed the importance of heat leak and heat loss reduction of cold box. Also, the unit process of ASU which requires thermal integration was confirmed.