• 한국환경보건학회지
• /
• 제35권5호
• /
• pp.411-416
• /
• 2009

This study was initiated to improve the cooling water quality by chemical coagulation and sedimentation in steel mills. Due to the inefficient flocculation in the settling tanks of blast furnace cooling water systems, the solid particles in the cooling water overflow accumulate and clog the cooling system. To protect the cooling water system from such fouling, proper flocculants must be continuously used. Laboratory tests were performed for the indirect cooling water system of a plate mill. The batch test in the gas scrubbing cooling water system of a blast furnace showed that the proposed coagulant was more effective for the improvement of coagulation and sedimentation than the existing one. During the tests, cationic flocculants were more effective than use of only an anionic flocculant. The suggested combination of anionic and cationic flocculants can probably improve the turbidity removal efficiency of the cooling water. Proper control of the overflow rate by the designed residence time would help turbidity removal efficiency in the settling tank. In addition, the settling can be enhanced by adopting rapid and slow mixing alternatively. Scale problems in blast furnace cooling water system were reduced to some extent by efficient settling.

• 전자공학회논문지S
• /
• 제35S권8호
• /
• pp.21-31
• /
• 1998

본 논문에서는 복사 네트워크의 멀티캐스트 셀을 적절하게 분배할 수 있는 새로운 분배 알고리즘을 제안한다. 합산기, 분배기, 가상 주소 부호기, 방송 네트워크가 이원적으로 구성된 복사 네트워크는 제안된 분배 알고리즘에 의하여 낮은 번지와 높은 번지가 양분되어 동시에 동작하기 때문에 입력된 셀이 균등하게 처리되어 셀 지연율과 입력 공정성이 개선되고 복잡도가 감소된다. 또한 방송 네트워크로 이진 트리와 Banyan 네트워크로 구성된 확장 Banyan 네트워크를 사용하여 오버플로우 발생 확률을 1/2로 감소 시킨다. 분석 결과 제안된 알고리즘은 입력 버퍼에서 셀 지연율이 확연하게 감소됨을 알 수 있었다.

• 산업경영시스템학회지
• /
• 제35권4호
• /
• pp.179-185
• /
• 2012

When manufacturing die casting mold, generally, the casting layout design should be considered based on the relation among injection system, casting condition, gate system, and cooling system. Also, the extent or the location of product defects was differentiated according to the various relations of the above conditions. In this research, in order to optimize casting design of an automobile part (Gear Box) Computer Aided Engineering (CAE) was performed by using the simulation software (Z Cast). The simulation results were analyzed and compared with experimental results. During the mold filling, internal porosities caused by air entrap were predicted and reduced remarkably by the modification of the gate system and the configuration of overflow. With the solidification analysis, internal porosities caused by the solidification shrinkage were predicted and reduced by the modification of the gate system. For making a better production die casting tool, cooling systems on several thick areas are proposed in order to reduce internal porosities caused by the solidification shrinkage.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.65-65
• /
• 2000

For Video on Demand(VoD) servers, a design of an efficient scheduler is important to the support a large number of clients having various playback speeds and receiving rates. In this paper, we propose the scheduling algorithm to handle establishing deadlines and selection using the earliest deadline first. To establish deadlines and selections, the period of the receiving rates for each client is located between the over-max receiving rate and the over-playback rate. To avoid video starvation and the buffer overflow of each client, the proposed algorithm guarantees providing the admission control. Because of establishing deadlines and selection, period of each client receiving is between one over max receiving rate and one over play back rate. Using Virtual Buffer in server, scheduling load is reduced. The efficiency of the proposed algorithm is verified using a Petri Net_Based simulation tool, Exspect.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.533-536
• /
• 1988

For CMOS, this paper propose a new global routing algorithm in which macrocells and I/O padcells can be treated. Not only predefined feedthrough in base array, but also some polysilicon line which are not assigned as inputs are used to prevent the overflow of nets passing through the row. The signal nets are assigned on their feedthrough by the maze router. By treating macrocells and I/O padcell, the routing from internal to I/O cell can be done automatically and a kind of is constraints in design process can be reduced.

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.878-885
• /
• 2009

One of important factors in designing MEMS resonators for RF filters is obtaining a desired frequency response function (FRF) within a specific frequency range of interest. Because various array-type MEMS resonators have been recently introduced to improve the filter characteristics such as bandwidth, pass-band, and shape factor, the degrees of freedom (DOF) of finite elements for their FRF calculation dramatically increases and therefore raises computational difficulties. In this paper the Krylov subspace-based model order reduction using moment-matching with non-zero expansion points is represented as a numerical solution to perform the frequency response analyses of those array-type MEMS resonators in an efficient way. By matching moments at a frequency around the specific operation range of the array-type resonators, the required FRF can be efficiently calculated regardless of their operating frequency from significantly reduced systems. In addition, because of the characteristics of the moment-matching method, a minimal order of reduced system with a prearranged accuracy can be determined through an error indicator using successive reduced models, which is very useful to automate the order reduction process and FRF calculation for structural optimization iterations. We also found out that the presented method could obtain the FRF of a $6\times6$ array-type resonator within a seventieth of the computational time necessary for the direct method and in addition FRF calculation by the mode superposition method could not even be completed because of a data overflow with a half after calculation of 9,722 eigenmodes.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제8권3호
• /
• pp.1105-1118
• /
• 2014

In this paper, a new reversible data hiding method based on a dual binary tree of embedding levels is proposed. Four neighborhood pixels in the upper, below, left and right of each pixel are used as reference pixels to estimate local complexity for deciding embeddable and non-embeddable pixels. The proposed method does not need to record pixels that might cause underflow, overflow or unsuitable for embedment. This can reduce the size of location map and release more space for payload. Experimental results show that the proposed method is more effective in increasing payload and improving image quality than some recently proposed methods.

• 한국대기환경학회지
• /
• 제16권6호
• /
• pp.675-684
• /
• 2000

A novel dry and wet deposition collector, which can overcome the several problems such as water evaporation cartridge cracks and high costs founded in the previous collector systems, has been constructed. ENVI-18 SPE adsorption cartridge has been used to measure atmospheric deposition of polycylic aromatic hydrocarbons (PAHs). A surrogate surface, consisted of water and methanol, was filled in the dry deposition funnel to simulate dry deposition onto water surface. A water supply system in order to compensat evaporation of the surrogate surface was used and it was consisted of a piston pump, a tubing pump, a overflow tube and a chamber system. A novel water vaporizing system to supply water onto the wet SPE cartridge system with a constant flow rate was developed. The novel water vaporizing system, consisted of a vacuum pump, a water supply reserviour and tube and a mini space heater, could prevent the PAHs adsorption cartridge cracks occurred in the previous collector and effectively adsorb PAHs. The novel dry and wet deposition collector showed a good adsorption, desorption, and recovery rates of PAHs. By reducing the number of pumps used and employing polypyopylene (PP) instead of teflon as a material of collection funnel, the total construction costs were much reduced as compared with the previous dry and wet deposition collectors.

• KIEAE Journal
• /
• 제14권3호
• /
• pp.15-21
• /
• 2014

In this study, we developed a modular rainwater infiltration system that can be applied for general purposes in urban areas to prepare for localized heavy rain caused by climatic change. This study also analyzed the system's effects on reducing runoff. An analysis of the system's effects on reducing runoff based on rainfall data and monitoring data obtained between September 2012 and December 2013 after the system was installed showed that approximately 20~22% of the runoff overflowed from the infiltration facility. Also, an analysis of the runoff that occurred during the monsoon season showed that 25% of the runoff overflowed through the storm sewer system of the urban area. These results show that the rainwater overflows after infiltrating the detention facility installed in the area during high-intensity rainfall of 100mm or higher or when precipitation is 100mm for 3~4 days without the prior rainfall. According to precipitation forecasts, torrential rainfall is becoming increasingly prevalent in Korea which is increasing the risk of floods. Therefore, the standards for storm sewer systems should be raised when planning and redeveloping urban areas, and not only should centralized facilities including sewer systems and rainwater pump facilities be increased, but a comprehensive plan should also be established for the water cycle of urban areas. This study indicates that decentralized rainwater management can be effective in an urban area and also indicates that the extended application of rainwater infiltration systems can offer eco-friendly urban development.

• ETRI Journal
• /
• 제27권6호
• /
• pp.691-696
• /
• 2005

In asynchronous transfer mode (ATM) networks, fixed length cells of 53 bytes are transmitted. A cell may be discarded during transmission due to buffer overflow or a detection of errors. Cell discarding seriously degrades transmission quality. The quality degradation can be reduced by employing efficient forward error control (FEC) to recover discarded cells. In this paper, we present the design and implementation of decoding equipment for FEC in ATM networks based on a single parity check (SPC) product code using very-large-scale integration (VLSI) technology. FEC allows the destination to reconstruct missing data cells by using redundant parity cells that the source adds to each block of data cells. The functionality of the design has been tested using the Model Sim 5.7cXE Simulation Package. The design has been implemented for a $5{\times}5$ matrix of data cells in a Virtex-E XCV 3200E FG1156 device. The simulation and synthesis results show that the decoding function can be completed in 81 clock cycles with an optimum clock of 56.8 MHz. A test bench was written to study the performance of the decoder, and the results are presented.