• Journal of the Korean Institute of Navigation
• /
• v.20 no.1
• /
• pp.47-58
• /
• 1996

The use of high tensile steel plates is increasing in the fabrication of ship and offshore structures. The main portion of ship structure is usually composed of stiffened plates. In these structures, plate buckling is one of the most important design criteria and buckling load may usually be obtained as an eigenvalue solution of the governing equations for the plate. To use the high tensile steel plate effectively, its thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. When the panel elastic buckling is allowed, it is necessary to get precise understandings about the post-buckling behaviour of thin plates. It is well known that a thin flat plate undergoes secondary buckling after initial buckling took place and the deflection of the initial buckling mode was developed. From this point of view, this paper discusses the post-buckling behaviour of thin plates under thrust including the secondary buckling phenomenon. Series of elastic large deflection analyses were performed on rectangular plates with aspect ratio 3.6 using the analytical method and the FEM.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.4
• /
• pp.281-288
• /
• 2018

Acoustic radiation efficiency is a crucial factor to estimate Underwater Radiated Noise (URN) of ships accurately. This paper describes a numerical method to analyse acoustic radiation efficiency of one side-wetted rectangular Mindlin plate with simply supported boundaries excited by a harmonic point force. Transverse displacements of plate and acoustic radiation pressures are evaluated by the mode superposition method. The acoustic radiation efficiencies analyzed by both Mindlin and thin plate theories show little differences at monopole and corner modes of low frequency regions but relatively large differences at edge and critical modes of high frequency regions. Especially, the critical frequency with the highest acoustic radiation efficiency evaluated by the Mindlin plate theory is higher than that of thin plate theory. In addition, the acoustic loading effect of fluid also increases bending wave-number of plate and its critical frequency. Finally, the acoustic radiation characteristics of plates with different aspect ratios and thicknesses through numerical analyses are investigated and discussed.

• Structural Engineering and Mechanics
• /
• v.53 no.1
• /
• pp.131-146
• /
• 2015

In the present paper a three-dimensional non-linear truss element and a short computer program for the modeling and predicting approximate lateral deflections in thin glass plates by the method of incremental loading are proposed. Due to the out-of-plane large deflections of thin glass plates compared to the plate thickness within each loading increment, the equilibrium and stiffness conditions are written with respect to the deformed structure. An application is presented on a thin fully tempered monolithic rectangular glass plate, laterally supported around its perimeter subjected to uniform wind pressure. The results of the analysis are compared with published experimental results and found to have satisfactory approximation. It is also observed that the large deflections of a glass plate lead to a part substitution of the bending plate behavior by a tensioned membrane behavior which is favorable.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.15 no.2
• /
• pp.1-11
• /
• 1978

Using the elliptical cylindrical function, the added masses of thin rectangular plates vibrating elastically in an infinite ideal fluid are calculated. For the boundary conditions of the plates, two models are adopted. The plate which is simply-supported on two opposite edges while the other edges are clamped is one and the other is the plate which is simply-supported on two opposite edges while the other edges are free. Same examples are calculated numerically for the fundamental mode in each cases. And the effect of the boundary condition on the added mass are investigated by comparing these data with those of Kim's[4] which were calculated for the simply-supported plates by the same method. It is concluded that it is possible to predict the added mass of a rectangular plate, whose boundary condition is not treated in this report, by using the result of this investigation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.65-72
• /
• 1994

Collapse characteristics of thin-walled hatted section tubes are investigated. The square section members with flanges are substituted by the equivalent rectangular tube. The stiffening effects of flanges are transformed to the restraining plate with the equivalency of buckling strength. The square tubes of single-hatted and double-hatted sections are investigated. The double-hatted section members show symmetric and antisymmetric crushing modes depending on the stiffness of flanges. The single-hatted section members show only symmetric modes. The bifurcation point of the compact crushing modes are investigated by experiments and shown almost same thickness-width ratio of the rectangular tubes. A large maximum crippling strength can be obtained by double-hatted section members with proper flange dimensions.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.3 s.28
• /
• pp.55-65
• /
• 1996

For stability analysis of stifened rectangular thin plates with various boundary conditions, Ritz method is presented. An energy method is especially useful in those cases where a rigorous solution of the diferential eqution is unknown or where we have a plate reinforced by stiffeners and it is required to find only an approximate value of the critical load. The strain energy due to the plate bending and the work done by the in-plane forces are taken into account in order to apply the principle of the minimum potential energy. The buckling mode shapes of flexural beams with various boundary conditions are derived, and shape functions consistent with the given boundary conditions in the two orthogonal directions are chosen from those displacement functions of beams. The matrix equations for stability of stiffened rectangular thin plates are determined from the stationary condition of the total potential energy. Numerical example for stability behaviors of horizontally and vertically stiffened plates subjected to uniform compression, bending and shear loadings are presented and the obtained results are compared with other researchers' results.

• Steel and Composite Structures
• /
• v.49 no.6
• /
• pp.713-728
• /
• 2023

This paper aims to investigate the free vibration analysis of FG plates, taking into account the effects of even and uneven porosity. The study employs the Hellinger-Reisner functional and obtains the element's bending stress and membrane stress fields from the analytical solution of the governing equations of the thick plate and plane problem, respectively. The displacement field serves as the second independent field. While few articles on free vibration analysis of circular plates exist, this paper investigates the free vibration of both rectangular and circular plates. After validating the proposed element, the paper investigates the effects of porosity distributions on the natural frequency of the FG porous plate. The study calculates the natural frequency of thin and thick bending plates with different aspect ratios and support conditions for various porosity and volume fraction index values. The study uses three types of porosity distributions, X, V, and O, for the uneven porosity distribution case. For O and V porosity distribution modes, porosity has a minor effect on the natural frequency for both circular and rectangular plates. However, in the case of even porosity distribution or X porosity distribution, the effect of porosity on the natural frequency of circular and rectangular plates increases with an increase in the volume fraction index.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.357-362
• /
• 2000

In the present paper the plastic buckling of thin-walled rectangular tube is analyzed. The stress-strain relations of the plates of the tube are idealized into nonlinear material of Ramberg and Osgood. Computing elastic moduli of the nonlinear material a precise plastic buckling stress has determined. The plastic buckling stress of the wider plate of the tube is considered as the crippling strength of the tube. The present theory is in good agreement with the experiments in various thickness-width ratios and materials.

• Structural Engineering and Mechanics
• /
• v.72 no.4
• /
• pp.491-502
• /
• 2019

This paper explores the analytical buckling solution of rectangular thin plates by the finite integral transform method. Although several analytical and numerical developments have been made, a benchmark analytical solution is still very few due to the mathematical complexity of solving high order partial differential equations. In solution procedure, the governing high order partial differential equation with specified boundary conditions is converted into a system of linear algebraic equations and the analytical solution is obtained classically. The primary advantage of the present method is its simplicity and generality and does not need to pre-determine the deflection function which makes the solving procedure much reasonable. Another advantage of the method is that the analytical solutions obtained converge rapidly due to utilization of the sum functions. The application of the method is extensive and can also handle moderately thick and thick elastic plates as well as bending and vibration problems. The present results are validated by extensive numerical comparison with the FEA using (ABAQUS) software and the existing analytical solutions which show satisfactory agreement.

• Journal of Sensor Science and Technology
• /
• v.10 no.1
• /
• pp.71-79
• /
• 2001

The use of a glass-plate probe of rectangular shape is proposed for the measurement of transmission loss in optical waveguides. The light-collecting window is of a thin, rectangular shape and is perpendicular to the light streak, while the conventional fiberglass probe has a small circular face. This transversely elongated form results in a grate improvement of mechanical tolerance for the probe movement in the vortical as well as in the transverse direction. A theoretical investigation also presents a reasonable agreement with the experiments.