• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 PARALLEL CFD 2006
• /
• pp.395-397
• /
• 2006

Air interlacing serves to protect the yarn against damage, strengthens inter-filament compactness or cohesion, and ensures fabric consistency. The air interlacing nozzle is used to introduce intermittent nips to a filament yarn so as to improve its performance in textile processing. The effect of various interlacing nozzle geometries on the interlacing process was studied. The geometries of interlacing nozzles with single or multiple air inlets located across the width of yarn channels are investigated. The basis case is the yarn channel, with a perpendicular main air inlet in the middle. Other cases have main air inlets, slightly inclined double sub air inlets, The yarn channel cross sectional shapes are either semicircular or rectangular shapes. The compressed impinging jet from the main air inlet hole hits the opposing bottom wall of the yarn channel, is divided into two branches, joins with the compressed air coming out from sub air inlet at the bottom and creates two free jets at both ends of the yarn channel. The compressed air movement in the cross-section consists of two opposing directional vortices. The CFD-FASTRAN flow parallel solver was used to perform steady simulations of impinging jet flow inside of the interlace nozzles. The vortical structure and the flow pattern such as pressure contour, particle traces, velocity vector plots inside of interlace nozzle geometry are discussed in this pater.

• 물과 미래
• /
• 제28권4호
• /
• pp.147-154
• /
• 1995

본 연구에서는 특별한 에너지 감세를 위한 수공구조물이 설치되지 않은 중 소규모 단락부 하류부에서 자유낙하하는 수맥으로 인하여 발생되는 비점착성 하상재료의 세굴특성을 수리모형실험을 통하여 분석하였다. 단락수맥 하류부에서의 세굴특성을 분석하기 위하여 먼저 직사각형 단락수맥의 흐름특성을 조사하였으며, 하상재료, 유량, 하류수심을 변화시키면서 세굴공의 직하류부에 생성되는 둔덕(mound)의 유무로 인한 세굴특성을 비교 분석하였다. 평형세굴심 뿐만 아니라 둔덕의 높이도 밀도 후르드수의 함수로 표시되며, 밀도 후르드수는 다른 무차원량 보다 평형세굴심과 비교적 깊은 관계가 있는 것을 확인하였다. 단락부 하류부 하상 보호공의 설계시 둔덕의 영향을 고려해야 한다는 결론을 얻었다.

• 한국유체기계학회 논문집
• /
• 제8권2호
• /
• pp.23-30
• /
• 2005

The rotary compressor is widely used in the air conditioner because it is efficient and compact. Recently, the need for silent and efficient compressors is much stronger than the past. The new type muffler was invented to reduce the noise level and to improve the efficiency. The new type muffler that has two side discharge holes and dome shape resulted in much lower overall noise level, especially noise levels around 1kHz than the old type one of one center discharge hole in the acoustic spectra. Also it showed a higher efficiency of air conditioner by lowering oil discharging amount of a compressor than old type one of a rectangular shape and two side discharge holes. The noise reduction and efficiency improvement by the new type muffler were verified by tests for votary compressors and air conditioners.

• 동력기계공학회지
• /
• 제16권4호
• /
• pp.44-50
• /
• 2012

The present numerical study was performed to determine how the two perforated baffles( Inclined angle=$5^{\circ}$; perforation diameter=2cm) placed at a rectangular duct affect heat transfer and associated friction factors. The parametric effects of perforated baffles(3, 6 and 12 holes) and flow Reynolds number ranging from 28,900 to 61,000 on the heated target surface are explored. As for the investigation of heat transfer behaviours on the local Nusselt number with two baffles placed at $x/D_h=0.8$ and $x/D_h=0.8$ of the edge baffles, it is evident that the average Nusselt number increases with increasing number of holes, but the friction factor decreases with an increase in the hole number placed at baffles. The numerical results by commercial code CFX 10.0 are confirmed with the experimental data.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2004년도 학술발표회
• /
• pp.429-433
• /
• 2004

According to researchers, the influential factors of scouring are generally divided into three factors: the flow conditions, the type and position of structures, and the characteristics of bed materials. In addition, scouring is affected by the 3-dimensional turbulent boundaries, the unsteady flow, the movement of sediment in the scour-hole area, the approach flow velocity and depth, the width of bridge foundation/pier, and the particle size of bed materials. However, it is difficult to estimate the scour depth near bridge piers when all conditions are factored in at once. Therefore, for reasonably accurate estimates of scour depth, it is essential to consider sufficiently the flow force and resisting force for scour. That is, to determine the shear stress concerning the bed material distribution is needed. In this study, the experiments were performed under the condition of a steady state of flow. As a result, scouring occurred at velocity ratios of 0.476,$(V/V_c=0.476)$, and the scour depth was increased linearly as the velocity ratio increased. in addition, the average values of shear stress ratio at zero scouring depth in both rectangular and circular piers were approximately 7$(\tau_c/\tau_{approach})$ and in the case for same size bed particle material. The results of this study can be used for the fundamental material for estimating the scour depth of bed materials.

• 설비공학논문집
• /
• 제25권6호
• /
• pp.317-323
• /
• 2013

A multi-perforated tube indicates the existence of multiple holes of various shapes on the surface of a long cylinder-type or rectangular tube, and a hole installed on the surface is called an orifice, as it is relatively small in size, compared with the surface area of the tube. In this study, the flow characteristics of a circular multi-perforated tube with many orifices on the surface were investigated experimentally and numerically. The volume flowrate issuing from each orifice, discharge angle, effective flow area ratio, and the flow fields around the orifices were measured and visualized, with the variation of the orifice area ratio, at the same blockage ratio. The volume flowrate distributions along the flow direction of the multi-perforated tube tends to be more uniform, as larger orifices were positioned at the inlet side of the multi-perforated tube, compared with no orifice area change along the flow direction.

• KIEAE Journal
• /
• 제12권3호
• /
• pp.107-114
• /
• 2012

This is a study that surveyed and analyzed the present status of producing loess construction materials in Korea from 2006 to 2011. The findings are as follows. 1) More than 70% of loess construction material manufacturers are distributed in the capital area. Chungcheong-do and Gyeonggi-do are grown by about 20% on the annual average. 2) Shape of loess brick is possessed mostly by a rectangular parallelepiped. A hole shape, which has 1~5 holes among these things, is possessing a majority. 3) It was indicated to be 42 days as material age for the compressive strength, to be about 2.7Mpa for both extrusion and compression, and to be about 30% for absorptance. 4) Among the whole loess material manufacturers, it accounts for 87 for loess brick 66% for loess mortar and more than 39% for loess paint, but within 10%~15% for other loess products. 5) The main specifications of loess brick are $300{\times}150{\times}150,\;300{\times}150{\times}100,\;300{\times}200{\times}150,\;300{\times}150{\times}200$ in order of the output of 74kinds of loess bricks. 6) In order to improve the strength of building materials, mortar and concrete used loess, it is necessary to examine closely about the effect of ceramic binder and cement on loess products.

• 헤리티지:역사와 과학
• /
• 제52권4호
• /
• pp.124-141
• /
• 2019

연구는 월지(안압지)의 수질 관리 문제를 유지용수의 순환 체계와 연관지어 접근하였다. 이를 위해 연못의 순환체계와 관련 깊은 입·출수 체계를 검토하였으며, 기존의 입·출수시설 외에 선행 연구에서 제기되었던 추정 입·출수시설을 분석하였다. 입수시설을 검토한 결과, 현재 입수구인 월지 동남측 호안 입수시설은 남북 담장을 사이에 두고 동편의 정원시설(경석, 곡수로, 저수시설)과 수로로 연결된 것으로 파악되었다. 월지 동편 조사에서 별도의 시설군이 있었던 것으로 보이며 1920년대 실측 도면에 경석군이 확인된 것이 이를 뒷받침한다. 추정 입수구인 남서측 호안 입수시설은 월지 서편 건물지 임해전(臨海殿) 터에 남아 있는 화강암 수로와 연관성이 있어 보인다. 월지 남서측 호안을 향해 경사가 낮아지고, 거름망을 꽂았던 홈, 1920년대 실측 도면과 1975년 측량 도면의 입수구에 경석이 배석되어 있는 것으로 보아 깨끗한 물을 입수시키기 위한 것으로 판단된다. 출수시설과 관련하여 북측 호안 출수시설은 총 5단계로 구성되어 있는데, 이 중 목제 수로와 장대석군 집수시설의 기능은 월지의 물을 배수하기 위한 시설만으로는 보이지 않는다. 목제 수로에 나무 물마개가 있는 점과 마지막 단계에 집수시설이 있는 점으로 미루어보아 상황에 따라 발천의 물이 역으로 입수될 수 있다고 판단된다. 즉 북측 호안 출수시설은 양방향으로 물이 드나들었으며 장대석군 집수시설을 통해 개폐 가능한 목제 수로로 입수되기도 한 것으로 판단된다. 추정 출수구인 서측 호안 출수시설은 북측 호안의 출수시설과 매우 유사함을 볼 때 신라시대에 존재하였거나 후대의 어느 시점에 북측 호안 출수시설을 모방하여 만들었을 것이라는 추정 외에는 어려운 실정이다. 다만 조선시대 어느 시점까지는 농업용수 공급을 위한 출수시설로 기능하였을 것으로 보인다. 이상과 같이 월지는 신라 왕경 중심부인 동궁의 시설과 유기적으로 얽혀 있는 체계화된 배수망에 의해서 입·출수가 이루어졌다. 이를 통해 월지를 비롯한 각 시설군에 물이 입수되었으며 왕경 중심부의 중요한 인공 하천인 발천(撥川)을 통해 남천(南川)으로 연결되는 배수 체계를 가지고 있었다.

• 한국전자파학회논문지
• /
• 제24권1호
• /
• pp.11-19
• /
• 2013

본 논문에서는 기생 소자의 커플링 현상을 이용하여 다중 대역 특성을 나타내기 위한 평면형 모노폴 안테나를 설계 및 제작하였다. 제안된 안테나는 단일 공진이 발생하는 사각 패치를 기본으로 다중 대역 특성을 얻기 위해 기생 소자를 삽입하였다. 기생 소자는 안테나 크기의 소형화와 다중 공진 특성을 나타내기 위해 스파이럴 구조를 사용하였으며, 각각의 설계 파라미터들을 이용하여 주파수 특성을 최적화 시켰다. 또한, via-hole을 통해 접지면에 연결된 L자 형태의 공진기를 급전선 양쪽에 삽입함으로써 서비스 대역 이외에 사용되지 않는 주파수 대역을 차단하였다. 사용된 기판은 크기가 $40{\times}60{\times}1mm^3$이고, 비유전율 4.4인 FR-4 기판 위에 설계되었으며, 급전은 임피던스 $50{\Omega}$의 마이크로스트립 선로를 사용하였다. 측정 결과, 1.714~2.496 GHz, 2.977~4.301 GHz, 4.721~6.315 GHz 대역에서 -10 dB 이하의 반사 손실 특성을 나타냈으며, 전방향의 방사 패턴을 나타냈다.

• 한국의상디자인학회지
• /
• 제18권3호
• /
• pp.71-83
• /
• 2016

This study attempted to analyze trends of structural changes in the front middle part of men's underwear and get basic data for the development of men's underwear patterns. In terms of a research method, the structure and pattern of the front middle part of men's underwear were analyzed by referring to the design and description of the drawing, focusing on men's underwear which targeted to isolate penis from scrotum among the 'men's underwear' or 'functional men's underwear'-related patents. According to the study, three topics were obtained as follows: a support attached to the inside of the front middle part; inner cloth attached to the inside of the front middle part; change in the structure of the front middle panel. The aspects by the specific topic targeted to isolate penis from scrotum and prevent the scrotum from adhered to a thigh are as follows: 1) When a support is attached to the inside of the front middle part, the following three methods are proposed: Penis isolated from scrotum by a rest which is designed using the band; penis and scrotum rested in the band and in a pocket respectively; protruded rest inside the front middle part of the underwear. 2) When an inner cloth is attached to the inside of the front middle part, the following methods are designed: A pocket-type inner cloth is attached; isolation of penis hole from the scrotum pocket using a rectangular separator; U-shaped pocket designed to rest penis and scrotum is attached. 3) Regarding change in the structure of the front middle panel, the integration of penis and scrotum resting parts can be divided into two cases: Securing a space using wrinkles; keeping it voluminous using the vertical line. In this all-in-one penis and scrotum-holding type, in addition, different front panel patterns were applied.