• Advances in Energy Research
• /
• v.8 no.3
• /
• pp.137-144
• /
• 2022

This study presents an experimental investigation of conventional and enhanced receiver tube performance for the application of a concentrated parabolic trough collector (CPC). The CPC system is fabricated and tested for the conventional and enhanced receiver tubes. The experiments were performed on both tubes for the change of flow rates. The temperature rise of the tube surface, as well as working fluid, were monitored for varying flow rates. The results were compared and discussed in view of enhanced CPC system performance. The results exhibited that the temperature rise of the working fluid passing through the tube was more in the case of the enhanced tube compared to the conventional receiver tube under the same flow rates.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.1
• /
• pp.69-78
• /
• 1999

The attitude determination system is indispensable for navigation, guidance and control tasks. In order to construct this system some special products that use dual frequencies or have on receiver engine with multiple antennas are used. But they are so expensive. Thus there are still strong requirements for the conventional low cost single frequency off-the-shelf receiver. This paper will propose a new technique to resolve integer ambiguity with single frequency GPS receiver and will show the problems of the attitude applications in which low cost receiver are being used. Also, based on this new technique precise attitude determination is presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.187-195
• /
• 1996

Because an alternative refrigerant(HFC-134a) is being used instead of CFC-12 for automotive air-conditioning system, newly designed air-conditioning components are necessary due to changes in characteristics. Optimum design scheme for receiver dryer in an automotive air-conditioning system is described with emphases upon the volume of desiccant and container. The volume of the container, that is manufactured based on the study, is reduced down to one half of the existing receiver dryers.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1987.04a
• /
• pp.86-92
• /
• 1987

We implement an universal signaling equipment including many kinds of singling devices just as R2 MFC seder.receiver DTMF sender/receiver Tone sender sued in Digital Switching System the universal signaling equipment has two parts sender part and receiver part. The sender part is implemnted with ROM-LOOK-UP Table method and the receiver part is implemnted that the equipment satisfies the Recomandations of CCITT. Also the capability of the equipment is evaluated by the LCS(Local Call Simulatior)Test in the TDX-1A system.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.2089-2094
• /
• 2010

The importance of broadband wireless communication implemented at subway tunnels is growing up. At 18GHz wireless video transmission system, the transmitter requires a digital modulation method. At subway tunnel, A 18GHz's influence of the multi-pass padding is strong. OFDM digital modulation that is strong for multi-pass padding is recommended. In this paper, Suitable to a subway wireless video transmission OFDM receiver is designed. OFDM receiver system has 6dB gaion because uses diversity of space diversity and MRC(Maximum Ratio Combining) diversity. The transmitter system use C&ITechnologies's transmitter board. IF frequency of receiver is 480MHz. OFDM modulation parameter is as follow, The bandwidth is 8MHz, The numuber of carrier if 2,000, The modulation methode is QAM16, The guard interval is 1/32.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1671-1675
• /
• 2012

In this paper, we fabricate multi-channel receiver for radar system. This receiver at X-band can be received 8 signal of an identical characteristic, dynamic range has more than 80[dB]. To process direct received signals, this system has the built-in two digital de-modulators which offer the minimum loss on the receiving signal path and has high stability by adding Built-In Test. The gain, noise figure, difference of amplitude and phase on the signal path is respectively $14{\pm}2$[dB], 19[dB], ${\pm}2$[dB], $10^{\circ}$ and below.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.11
• /
• pp.1238-1246
• /
• 1992

We developed a time comparison system using the ranging signal of the geostationary meteorological satellite(GMS). By using the system time comparison between the KRISS(Korea Research Institute of Standards and Science) cesium atomic clock and the GMS ranging signal has been carried out and the results have shown that the precision of time comparison at KRISS is about 10 ns. For the more accurate measurements we calibrated the receiver delay time between KRISS receiver and CRL(Communications Research Laboratory) receiver by using the portable GMS receiver.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.12
• /
• pp.1240-1247
• /
• 2011

The localization of mobile robot in environment is a major concern in mobile robot navigation. So, many kinds of localization techniques have been researched for several years. Among them, the positioning system using ultrasound has received attention. Most of these ultrasonic positioning systems to synchronize the transmitters and receivers are used for RF (Radio Frequencies). However, due to the use of RF, the interference problems can not be avoided and the performance of radio frequencies directly affects the positioning performance. So we proposed the ultrasonic positioning system without synchronizing RF. The proposed system is based on existing USAT (Ultrasonic Satellite System) adopted infrastructure transmitting type, and consists of transmitter and receiver synchronizing modules instead of the radio frequency transmitters and receiver. The ultrasonic transmitters and receivers are synchronized individually by the transmitter and receiver synchronizing modules. In order to calculate the bias between the transmitter and receiver synchronizing modules, new positioning algorithm similar to GPS was proposed. The positioning performance of the improved USAT without synchronizing RF and the validity of the proposed positioning algorithm are verified and evaluated by experiments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.494-502
• /
• 2001

GPS(Global Positioning System) and GLONASS(GLObal Navigation Satellite System) are basic technologies providing the information of the position and the time, and they have various applications such as navigation, survey, control, and so on. However, each GPS and GLONASS has limited number of visible satellites, and, from the view of strategy, it is undesirable to be heavily dependent on only one system. Thus, GPS/GLONASS combined receiver became required to obtain more precise navigation and system stability. In this paper, the RF front end of GPS/GLONASS combined receiver was fabricated on 130$\times$80 $\textrm{mm}^2$ PCB(Printed Circuit Board), and its system application was shown finally one chip possibility of GLONASS receiver is studied.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.10
• /
• pp.8-17
• /
• 1995

Recently, in a variety of the application fields, it is interested in GPS receiver as the use of GPS(Global Positioning System) is increased. In this paer, we propose that a type of new receiver of a simple structure as GPS data receiver. This proposed receiver consists of RF stage, local C/A(Coarse/Acquisition) code generator, C/A code correlator, data demodulator and microprocessor controller as a GPS single channel data receiver using the L1 carrier . It is confirmed that the proposed receiver operates well as GPS raw data receiver through experiment.