Transactions on Electrical and Electronic Materials
/
제15권2호
/
pp.77-80
/
2014
The effect of reactive diluents on the ac electrical treeing in epoxy/nanosilicate systems was studied, in a needle-plate electrode geometry. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and layered silicate was used as a nano-sized filler. Polyglycol (PG) or 1,4-butanediol diglycidyl ether (BDGE) was introduced as a reactive diluent to the DGEBA/nanosilicate system, in order to decrease the viscosity of the nanocomposite system. PG acted as a flexibilizer, and BDGE acted as a chain extender, after the curing reaction. To measure the treeing propagation rate, a constant alternating current (ac) of 10 kV/4.2 mm (60 Hz) was applied to the specimen, in a needle-plate electrode arrangement, at $30^{\circ}C$ of insulating oil bath. When 10 kV/4.2 mm (60 Hz) was applied, the treeing propagate rate in the DGEBA system was $1.10{\times}10^{-3}$ mm/min, and that in the DGEBA/PG system was $1.05{\times}10^{-3}$ mm/min. As 1.5 wt% of nanosilicate was added to the DGEGA/PG system, the propagation rate was $0.33{\times}10^{-3}$ mm/min. This meant that the nano-sized layered silicates would act as good barriers to treeing propagation. The effect of chlorine content was also studied, and it was found that chlorine had a bad effect on the electrical insulation property of the epoxy system.
This paper introduces a new methodology to apply the interpolation technique wi th optimum pattern to voltage-reactive power control of power system. The conventional tool for the optimal operation of power system is Optimal Power Flow(OPF) by standard optimization techniques. The achievement of solution through OPF programs has a defect of computation time, so that it is impossible to apply the OPF programs to the real-time control area. The proposed method presents a solution in a short period of time and an output with a good accuracy. The optimum pattern is a set of input-output pairs, where an input is a load level and a type of outage and an output is the result of OPF program corresponding to the input. The output in the OPF represents control variables of voltage-reactive power control. The interpolation technique is used to obtain the solution for an arbitrary input. As a result, the new technique helps operators in the process of the real-time voltage-reactive power control in both normal and emergency operating states.
Tin oxide thin films were prepared on borosilicate glass by rf reactive sputtering at different deposition powers, process pressures and substrate temperatures. The ratio of oxygen/argon gas flow was fixed as 10 sccm / 60 sccm in this study. The structural, electrical and optical properties were examined by the design of experiment to evaluate the optimized processing conditions. The Taguchi method was used in this study. The films were characterized by X-ray diffraction, UV-Vis spectrometer, Hall effect measurements and atomic force microscope. Tin oxide thin films exhibited three types of crystal structures, namely, amorphous, SnO and $SnO_2$. In the case of amorphous thin films the optical band gap was widely spread from 2.30 to 3.36 eV and showed n-type conductivity. While the SnO thin films had an optical band gap of 2.24-2.49 eV and revealed p-type conductivity, the $SnO_2$ thin films showed an optical band gap of 3.33-3.63 eV and n-type conductivity. Among the three process parameters, the plasma power had the most impact on changing the structural, electrical and optical properties of the tin oxide thin films. It was also found that the grain size of the tin oxide thin films was dependent on the substrate temperature. However, the substrate temperature has very little effect on electrical and optical properties.
부틸 아세테이트는 반응증류탑에서 초산과 부탄올의 에스테르 교환반응에 의해 제조된다. 공비첨가제는 반응영역에서 생성물인 물을 보다 효과적으로 분리할 수 있도록 하여, 반응증류탑의 성능을 향상시킨다. 중소 공장에서 회분식 공정은 연속공정에 비해 보다 유연하게 사용할 수 있다는 점에서 유리하다. 본 연구에서는 부틸아세테이트 합성을 위한 회분식 반응증류 공정과 반회분식 반응증류 공정에 대하여 공정 모사 및 실험을 통하여 연구하였다. 공정 성능 향상을 위하여 공비첨가제 종류, 공정구조에 대하여 조사하였다. 또한 반회분식 반응 증류탑을 연속 운전하여 새로운 순환 운전 방법을 제시하였으며, 이 조업 전략을 사용하여 높은 생산성과 안정한 조업이 가능함을 보였다.
KSII Transactions on Internet and Information Systems (TIIS)
/
제4권6호
/
pp.1098-1115
/
2010
An inseparable challenge associated with every random access network is the design of an efficient Collision Resolution Algorithm (CRA), since collisions cannot be completely avoided in such network. To maximize the collision resolution efficiency of a popular CRA, namely Binary Exponential Backoff (BEB), we propose a reactive backoff algorithm. The proposed backoff algorithm is reactive in the sense that it updates the contention window based on the previously selected backoff value in the failed contention stage to avoid a typical type of collision, referred as cross-collision. Cross-collision would occur if the contention slot pointed by the currently selected backoff value appeared to be present in the overlapped portion of the adjacent (the previous and the current) windows. The proposed reactive algorithm contributes to significant performance improvements in the network since it offers a supplementary feature of Cross Collision Exclusion (XCE) and also retains the legacy collision mitigation features. We formulate a Markovian model to emulate the characteristics of the proposed algorithm. Based on the solution of the model, we then estimate the throughput and delay performances of WLAN following the signaling mechanisms of the Distributed Coordination Function (DCF) considering IEEE 802.11b system parameters. We validate the accuracy of the analytical performance estimation framework by comparing the analytically obtained results with the results that we obtain from the simulation experiments performed in ns-2. Through the rigorous analysis, based on the validated model, we show that the proposed reactive cross collision exclusionary backoff algorithm significantly enhances the throughput and reduces the average packet delay in the network.
In this study, we constructed a database of dyeing concentrations of all reactive dyes used for dyeing linen according to the thickness of the linen fabric and attempted to improve the reproducibility of the dyeing process for the commercialization of linen fabric materials. Linen fabric is a natural cellulose material that is comfortable and suitable for eco-friendly trends. It is a typical summer material with excellent breathability and thermal conductivity, quick moisture absorption and dissipation, and a cool touch. Dyeability and fastness were evaluated depending on the thickness of the linen fabric using a monochlorotriazine (MCT) reactive dye and bifunctional yellow, red, and blue dyes. All three colors of the MCT reactive dye and bifunctional dyes exhibited a darker shade as the fiber thickness of the marker increased. Fastness to washing was excellent at grades 4-5 or higher, regardless of the color of the dye and the number of linen fabrics. Although some color-fastness differences were noted, with the color change occurring most frequently with blue color, the fastness variations with dye type were mostly similar. The results of this study are expected to facilitate the selection of reactive dyes according to the thickness of the linen fabric based on the basic data from the laboratory, which will aid in the mass production of linen fabric and benefit the fashion industry.
Second-order rate constants (kN) have been measured spectrophotometrically for reactions of 3,4-dinitrophenyl 2-thiophenecarboxylate (2) with a series of alicyclic secondary amines in 80 mol % $H_2O$/20 mol % dimethyl sulfoxide at 25.0 ${^{\circ}C}$. The Brønsted-type plot exhibits a downward curvature for the aminolysis of 2. The curved Brønsted-type plot is similar to that reported for the corresponding reactions of 2,4-dinitrophenyl 2- thiophenecarboxylate (1). The reactions of 1 and 2 have been suggested to proceed through the same mechanism, i.e., through a zwitterionic tetrahedral intermediate ($T^{\pm}$) with a change in the rate-determining step. Substrate 2 is less reactive than 1 toward weakly basic amines (e.g., $pK_a$ < 10.4) but becomes more reactive as the basicity of amines increases further. Dissection of kN into the microscopic rate constants has revealed that the reaction of 2 results in a smaller $k_2/k_{-1}$ ratio but larger $k_1$ than the corresponding reaction of 1. Steric hindrance exerted by the ortho-nitro group has been suggested to be responsible for the smaller $k_1$ value found for the reactions of 1.
여러 application에 적용하기 위하여 p-type SnO 박막과 전극 간의 접촉 저항을 분석이 필요하였다. 이를 Transmission Line Method(TLM) 패턴 소자를 제작한 후 전기적 특성을 분석함으로써 알 수 있었다. $Si/SiO_2$ 기판에 Reactive Magnetron Sputtering법을 이용하여 c축 우선 배향된 SnO를 100nm 증착하고 photolithography 공정을 통해 전극을 패턴화하여 100nm 두께로 증착하였다. 전극 간 거리는 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, $1024{\mu}m$로 각각 2배씩 증가하는 패턴이고 폭 W는 $300{\mu}m$ 이다. p-type SnO 의 경우, work function이 4.8eV이기 때문에 전극과 ohmic contact이 되기 위해서는 4.8eV보다 높은 work function 값을 가지는 전극이 필요하였다. 이 조건과 맞는 후보로 Ni(5.15eV), ITO(5.3eV)를 설정한 후 소자를 제작하였다. 제작된 소자는 열처리 하지 않은 소자와 Rapid Thermal Annealing(RTA) 장비에서 $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$에서 각각 1분씩 열처리한 소자의 특성을 분석하였다. 열처리 하지 않은 소자의 경우 Ni 전극의 specific contact resistance는 $3.42E-2{\Omega}$의 값을 나타내었고, ITO의 경우 $3.62E-2{\Omega}$값을 나타내었다.
반응성염료중 chlorotriazinyl계 염료로 견직물에 날염가공 하여, 증열시간, 호료의 점도, 알칼리농도에 의한 염착량 및 고착량을 측정하여 견에 대한 반응성염료의 날염특성에 관하여 연구한 결과를 다음과 같이 요약한다. 1) 증열시간과 더불어 염착량 및 고착량은 증가하였으며, dichlorotriazinyl계 염료는 20분부근에서 최대치를 나타내었다. 2) 고착률은 90%이상으로 높은 고착률을 나타내었다. 3) 호료의 점도에 따라 염착량 및 고착량은 달라지며, 적당한 점도가 필요함을 시사한다. 4) 알칼리 농도는 호료 100g에 대하여 NaHCO$_3$2g을 첨가하였을 때 염착량 및 고착량이 가장 높았다. 5) 염색견뢰도중, 실용상 가장 중요한 세탁견뢰도가 매우 높았다.
This paper represents a new type low power High Frequency technological ion source (HF TIS) for ion - beam processing: the surface modification of materials, cleaning of surface, sputtering, coating of thin films, and polishing. The operational principle of HF TIS is based on the excitation of electrostatic waves in plasma located in the external magnetic field. Low power HF TIS with diameter 92 rom gives the opportunity to obtain beams of inert and chemically reactive gases with currents range from 5 to 150 mA (current density $0.015\;~\;3.5\;mA/\textrm{m}^2$) and ion beam energy 100 ~ 2500 eV at a HF power level 10 ~ 150 W. Three grid concave type ion optical system (IOS) is used for extraction and formation ofion beam.n beam.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.