• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.5
• /
• pp.1649-1660
• /
• 1996

The flow around a circular cylinder was controlled by an acoustic excitation issued from a thin slit along the cylinder axis. The static pressure distributions around the cylinder wall and flow characteristics in the near wake have been measured. Experiments were performed under three cases of Reynolds number, 7.8 * 10$\^$4/, 2.3 * 10$\^$5/ and 3.8 * 10$\^$5/. The effects of excitation frequency, sound pressure level and the location of the slit were examined. Data indicate that the excitation frequency and the slit location are the key parameters for controlling the separated flow. At Re$\_$d/, = 7.8 * 10$\^$4/, the drag is reduced and the lift is generated to upward direction, however, at Re$\_$d/, =2.3 * 10$\^$5/ and 3.8 * 10$\_$5/, the drag is increased and lift is generated to downward direction inversely. It is thought that the lift switching phenomenon is due to the different separation point of upper surface and lower surface on circular cylinder with respect to the flow regime which depends on the Reynolds number. Vortex shedding frequencies are different at upper side and lower side. Time-averaged velocity field shows that mean velocity vector and the points of maximum intensities are inclined to downward direction at Re$\_$d/ = 7.8 * 10$\^$4/, but are inclined to upward direction at Re$\_$d/ = 2.3 * 10$\^$5/.

• Korean Journal of Medicinal Crop Science
• /
• v.9 no.1
• /
• pp.21-25
• /
• 2001

Major saponins in ginseng were analysed using reverse phase high performance liquid chromatography with binary mobile phase gradient control system instead of normal phase column. The optimum condition were as following : reverse phase column; ${\mu}{\beta}ondapak\;C_{18}$ column (Waters, $3.9mm{\times}300\;mm,\;5{\mu}m$), methyl cyanaide/water binary mobile phase gradient control system, solvent flow rate; 1.5 ml/min, and UV($203{\mu}m$ ) detector. The complete separation of ginsenoside $Rb_1,\;Rb_2,\;Rc,\;Rd,\;Re,\;Rf\;and\;Rg_1$ was achieved within 55 min. The Regression coefficients of the calibration curves for seven ginsenosides were 0.99.

• Journal of Navigation and Port Research
• /
• v.35 no.10
• /
• pp.805-810
• /
• 2011

An experiment was carried out to figure out the instantaneous flow characteristics in the wake of the transom stern's 2-dimensional section by 2-frame grey level cross correlation PIV method at $Re=3.5{\times}103$, $Re=7.0{\times}103$. The stern angles of models were learning at $45^{\circ}$(Model "A"), $90^{\circ}$(Model "B") and $135^{\circ}$(Model "C") respectively based on the survey results of real ships. The depth of wetted surface is 40mm from free surface. As Reynolds number increases, vortices increase in volume and move their way to the downstream. Flow separation appeared at the end of model's bottom.

• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.288-293
• /
• 2013

A group of molecularly imprinted polymers (MIPs) with specific recognition for chiral (S)-ibuprofen were successfully prepared based on hydrogen bonds, utilizing ${\alpha}$-methacrylic acid as a functional monomer. The IR analysis of MIPs showed that the blue- and red-shifted hydrogen bonds were formed between templates and functional monomers in the process of self-assembly imprinting and re-recognition, respectively. According to UV-Vis analysis, we found that the ratio of host-guest complexes between template molecule and functional monomer was 1:1. The effect of cross-linker's quantity on the polymerization was studied by transmission electron microscope (TEM). The adsorption selectivity experiments indicated that MIPs exhibited higher selectivity to (S)-ibuprofen than those to ketoprofen and (R)-ibuprofen, (S)-ibuprofen's structural analogs.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.5
• /
• pp.691-697
• /
• 2008

Heat exchangers are commonly used in practice in a wide range of application, from heat and air-conditioning system in a household, to chemical processing and power production in large plant. An Experimental study was conducted to investigated the fluid flow and heat transfer around four circular cylinders of in-line in a cross flow of air. The local and average heat transfer characteristics for tube banks are investigated in the present study. Heat transfer in a heat exchanger usually involves convection in each fluid and conduction through the wall separating the two fluid. The in-line pitch ratio was in the range $1.5{\leq}L/d{\leq}4.0$, where L is the center distance and d the cylinder diameter, and in the Reynolds number $8,000{\leq}Re{\leq}50,000$. The local and mean Nusselt numbers were estimated. Subsequently, the heat transfer characteristics of four circular cylinders are found to exhibit a strong dependency upon the separation point of their upstream cylinders.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.342-348
• /
• 2001

This study was conducted to obtain granular crystalline gypsum that can be used as raw material for plaster boards or cements from waste Plaster board. We could disintegrate preferentially gypsum to gypsum needle in 10${\mu}{\textrm}{m}$ or less size among the contents of waste plaster board (gypsum, paper, fiber, and inorganic material .etc.) by hydration afterwards the dehydration of crushed waste plaster board. In this case, the optimum conditions for minimizing the size of gypsum were dehydration rate of 75%~ 85%, hydration concentration of 10~20%, agitation speed of 250~400rpm, crushing size of 2cm or less. Gypsum of 98.21% grade was recovered with 99.0% yield from under screenings of 325mesh wet screening which followed by the dehydration-hydration process performed in the conditions of dehydration rate of 80%, hydration concentration of 15%, agitation speed of 300rpm, crushing size of 2cm or less. Subsequently, Plate-like Crystalline gypsum of is 151${\mu}{\textrm}{m}$ size and the grade of 99.49% with the Yield of 98.0% from the upper screenings of 270mesh wet screening carried out after the re-crystallization of the recovered gypsum needle slurry.

• Journal of Power System Engineering
• /
• v.12 no.5
• /
• pp.48-53
• /
• 2008

Heat exchangers are commonly used in practice in a wide range of application, from heating and air-conditioning system in a household, to chemical processing and power production in a large plant. Heat transfer in a heat exchanger usually involves convection in each fluid and conduction through the wall separating the two fluids. The heat transfer characteristics of tube banks of in-line arrangements of four circular cylinders in a cross flow are compared for a range of tube locations and Reynolds numbers. The in-line pitch ratio was set up in the range of $1.5\leq L/d\leq4.0$, where L is the center to center distance and d the circular cylinder diameter, and in the Reynolds number of $13,000\leq Re\leq50,000$. The local and mean Nusselt numbers were estimated, and then. Subsequently, the heat transfer characteristics of four circular cylinders were found to exhibit a strong dependency upon the cylinder spacing and separation point of their upstream cylinders.

• Journal of Veterinary Clinics
• /
• v.30 no.5
• /
• pp.394-398
• /
• 2013

An 3-year-old female Thoroughbred horse was referred with moderate lameness (3/5G) and mild heat on right hoof of forelimb. She was diagnosed with white line disease (WLD) that was included hoof wall separation by radiographic examination and hoof percussion. Treatment was carried out hoof wall resection at first, followed by disinfection of affected hoof and shod modified heart bar. On the re-examination after 4 months, we could find a results which had no lameness, gas pocket in the white line and clinical signs was improved. Subsequently, she was trained and raced after 8 months of diagnosis. So, we supposed that resection of wall and therapeutic shoeing was good for WLD including hoof separation.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.14 no.4
• /
• pp.24-30
• /
• 2006

An experimental study was carried out in order to investigate the influence of boundary layer behavior on the near-wake at low Reynolds numbers. An X-type hot-film probe(55R51) was used to measure the near-wake of an NACA 0012 airfoil at static angles of attack ${\alpha}=0^{\circ}$, $3^{\circ}$, and $6^{\circ}$, and the Reynolds numbers Re=2.3${\times}10^4$, 3.3${\times}10^4$, and 4.8${\times}10^4$. The results of the study show that the characteristics of the boundary layer on the airfoil surface have a close relationship with the mean velocity and turbulence intensity profiles of a near-wake. Therefore, the development of the boundary layer, the position of the separation point, and the existence and non-existence of reattachment on the airfoil surface were represented by the differences in mean velocity and turbulence intensity profiles of the near-wake.

• International conference on construction engineering and project management
• /
• 2011.02a
• /
• pp.221-228
• /
• 2011

As construction works have become larger and more complex, improving productivity by introducing Information Technology (IT) is pursued and more effective construction management is needed in construction industry. In this circumstance, many different kinds of project management system is being introduced, and various IT technologies are applied such as Personal Digital Assistant (PDA), Bar Code, Radio Frequency Identification (RFID), Web Camera, and so on. However, these kinds of technologies might cause re-processing of information and ineffectiveness of project because of lack of real time information processing technology or separation between construction sites and management offices. Meanwhile, these technologies rather decrease the construction productivity except for the data saving and database function. Therefore, this research aims to develop Application that can be applied efficiently for construction material management, by understanding problems of former management system with questionnaires and extracting functions with analysis of requirements. In virtue of the construction material management Application which will be developed in this study, it will be possible to input information automatically, to process and check material information in real time, and to identify the location of necessary material. Then, the problem of separation between construction sites and management offices are solved, and as a result, more efficient management of materials in construction sites will become possible. At the same time, this study will investigate the possibility and applicability of new IT device, Smart Phone to construction sites.