• Computers and Concrete
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2017

In this study, two types of aggregate were used for making self-compacting concrete. Standard cubic specimens were exposed to different temperatures. Seventy-two standard cylindrical specimens ($150{\times}300mm$) and Seventy-two cubic specimens (150 mm) were tested. Compressive strengths of the manufactured specimens at $23^{\circ}C$ were about 33 MPa to 40 MPa. The variable parameters among the self-compacting concrete specimens were of sand stone type. The specimens were exposed to 23, 100, 200, 400, 600, and $800^{\circ}C$ and their mechanical specifications were controlled. The heated specimens were subjected to the unconfined compression test with a quasi-static loading rate. The corresponding stress-strain curves and modulus of elasticity were compared. The results showed that, at higher temperatures, Scoria aggregate showed less sensitivity than ordinary aggregate. The concrete made with Scoria aggregate exhibited less strain. The heated self-compacting concrete had similar slopes before and after the peak. In fact, increasing heat produced gradual symmetrical stress-strain diagram span.

• Transactions of Materials Processing
• /
• v.7 no.2
• /
• pp.158-167
• /
• 1998

Hot restoration mechanism flow stress and stain of the Al2024 composites reinforced with 1,8,15,36, and $44{\mu}m\;SiC_p$(10 vol. %) were studied by hot torsion tests. The hot restoration mechanism of all the composites was found to be dynamic recrystallization(DRX) at $320^{\circ}C$ while that of the composites reinforced with 1 and $8{\mu}m\;SiC_p$ was found to be dynamic recovery(DRX) at $480^{\circ}C$. It was found that the Al2024 composite with $15{\mu}m\;SiC_p$ showed the highest flow stress(${\sim}$223 MPa) at $320^{\circ}C$ under a strain rate of 1.0/sec. Also the highest flow strain of the composites was obtained at $430^{\circ}C$. The com-posites reinforced with 1 and $8{\mu}m\;SiC_p$ showed lower flow stress and higher flow strain at $480^{\circ}C$ than those of the composites reinforced with 15, 36, and $44\;{\mu}m\;SiC_p$ These result were discussed in relation to the transition of the hot restoration mechanism. $DRX{\leftrightarrow}DRV$. The dependence of flow stress on strain rate and temperature was attempted to fit with the hyperbolic sine equation ($\dot{\varepsilon}=A[sinh({\alpha}{\cdot}{\sigma}_p]^n$ exp(-Q/RT)and Zener-Hollomon parameter($Z=\;\dot{\varepsilon}\;exp(Q/RT))$.

• Journal of Microbiology and Biotechnology
• /
• v.28 no.11
• /
• pp.1846-1849
• /
• 2018

Recent human gut microbiome studies have supported that the genus Bifidobacterium is one of the most beneficial bacteria for human intestinal health. To develop a new probiotic strain for functional food applications, fourteen fecal samples were collected from healthy Koreans and the strain BCBR-583 was newly selected and isolated from a 25-year-old Korean woman's fecal sample using the selective medium for Bifidobacterium. Subsequent fructose-6-phosphate phosphoketolase (F6PPK) test and 16S rRNA gene sequencing analysis of the strain BCBR-583 confirmed that it belongs to B. longum subsp. longum. The stress resistance tests showed that it has oxygen and heat tolerance activities (5- and 3.9-fold increase for 24 h at 60 and 120 rpm, respectively; $78.61{\pm}6.67%$ survival rate at $45^{\circ}C$ for 24 h). In addition, gut environment adaptation tests revealed that this strain may be well-adapted in the gut habitat, with gastric acid/bile salt resistance ($85.79{\pm}1.53%$, survival rate under 6 h treatments of gastric acid and bile salt) and mucin adhesion ($73.72{\pm}7.36%$). Furthermore, additional tests including cholesterol lowering assay showed that it can reduce $86.31{\pm}1.85%$ of cholesterol. Based on these results, B. longum BCBR-583 has various stress resistance for survival during food processing and environmental adaptation activities for dominant survival in the gut, suggesting that it could be a good candidate for fermented food applications as a new probiotic strain.

• Microbiology and Biotechnology Letters
• /
• v.24 no.5
• /
• pp.604-612
• /
• 1996

To improve the fermentation characteristics of the haploid starch-fermenting recombinant yeast strain K114/YIpMS$\Delta$R(LEU2/URA3) secreting both $\alpha$-amylase and glucoamylase was rare-mated with polyploid industrial yeast Saccharomyces sp. K35. The K35 strain had good fermentation-characteristics such as ethanol-tolerance, high temperature and sugar-tolerance, and high fermentation rate. Among the resulting 66 hybrids, the best strain RH51 was selected. The RH51 exhibited amylolytic activity of K114/YIpMS$\Delta$R(LEU2/URA3) as well as ethanol and sugar tolerance of K35. The optimum temperature of hybrid RH51 for starch fermentation was 34$\circ$C which was same as that of K35 but different from that (30$\circ$C) of K114/YIpMS$\Delta$R(LEU2/URA3). The optimum pH was 5.0. The optimum size of inoculum was 2% as the pellet (w/v) of yeast cells. The hybrid strain RH51 produced 7.0% ethanol (w/v) from 20% (w/v) soluble starch while K35 formed almost no ethanol, 0.3% (w/v). RH51 strain produced 7.5% (w/v) ethanol after 8 days in a 2.5 l fermenter containing 800 ml of 20% (w/v) soluble starch. The residual starch content in the fermentation medium was 1.68% (w/v), and therefore almost all the starch was fermented completely.

• The Plant Pathology Journal
• /
• v.22 no.4
• /
• pp.329-333
• /
• 2006

Two distinct and stable isolates of Barley mild mosaic virus(BaMMV) designated as Naju82-S(severe) and Naju82-M(mild) were obtained. These two isolates differed in their symptomatology, virus transmission characteristics and cultivar specificity at various temperature. Thus, these isolates were referred to as strains in this study. BaMMV Naju-S strain showed severe mosaic symptoms accompanied by necrosis on the infected leaves. Naju82-S strain is more virulent demonstrated by shorter incubation period and relatively high virus concentration than Naju82-M strain. Five Korean cultivars were tested for their pathogenicity to different strains based on the rate of infection. Results showed that infection rate of cultivars to both strains did not significantly differed from each other. However, under different temperatures, the pathogenicity on the two cultivars such as cultivars Hopumbori and Sessalbori were significantly affected. Hopumbori was moderately resistant to both strains at $10-12^{\circ}C$ and susceptible at $15-18^{\circ}C$. Similarly, Sessalbori was moderately resistant at $10-12^{\circ}C$ to both strains but distinctly differentiated at $15-18^{\circ}C$ wherein it was resistant to mild strain and highly susceptible to severe strain. Other cultivars including Baegdong, Jinyangbori and Neahanssalbori consistently showed susceptible reaction to both strains at varying temperatures tested in this study.

• Korean Journal of Materials Research
• /
• v.14 no.10
• /
• pp.713-718
• /
• 2004

To study the dynamic strain aging behavior of Zr-0.4Sn-1.5Nb-0.2Fe sample tube for nuclear fuel cladding in the range of pressurized water reactor (PWR) operation temperature, the tensile tests of the tube specimens, which had been finally heat-treated at $470^{\circ}C\;and\;510^{\circ}C$, had been carried out with the strain rate $1.67{\times}10^{-2}/s\;and\;8.33{\times}10^{-5}/s$ at the various temperatures from room temperature to $500^{\circ}C$. It was observed that the elongation of the specimens got shortened as the temperature increased from $200^{\circ}C\;to\;340^{\circ}C$. The specimens that were finally heat-treated at $470^{\circ}C$ showed a plateau more remarkably on the plot of yield strength-temperature than those heat-treated at $510^{\circ}C$. In the range of $310\sim400^{\circ}C$, the strain rate sensitivity of the specimens finally heat-treated at $510^{\circ}C$ was $30.4\%\sim33.7\%$ lower but the work hardening exponent index of the specimens was a little higher than that without dynamic strain aging effect.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.8
• /
• pp.938-945
• /
• 2005

The microstructure evolution in hot forging process is composed of dynamic recrystallization during deformation as well as grain growth during dwell time. Therefore, the control of forging parameters such as strain, strain rate. temperature and holding time is important because the microstructure change in hot working affects the mechanical properties. Modeling equations are developed to represent the flow curve. grain size. recrystallized volume fraction and grain growth phenomena by various tests. The developed modeling equations were combined with thermo-viscoplastic finite element modeling to predict the microstructure change evolution during hot forging process. The large exhaust valve spindle (head diameter of 512mm) was simulated by closed die forging with hydraulic press and cooled in air after forging. The preform was heated to each 1080 and 1150$^{\circ}C$. Numerical calculation was performed by DEFORM-2D. a commercial finite element code. Heat transfer can be coupled with the deformation analysis in a non-isothermal deformation analysis. In order to obtain the fine and homogeneous microstructure and good mechanical properties in forging. the FEM would become a useful tool in the simulation of the microstructure development. In forging, appropriate temperature, strain and strain rate and rapid cooling are required to obtain the fine grain microstructure The optimal forging temperature and effective strain range of Nimonic 80A for large exhaust valve spindle are about 1080$\∼$l120$^{\circ}C$ and 150$\∼$200$\%$.

• Earthquakes and Structures
• /
• v.8 no.3
• /
• pp.665-679
• /
• 2015

The strain rate of reinforced concrete (RC) structures stimulated by earthquake action has been generally recognized as in the range from $10^{-4}/s$ to $10^{-1}/s$. Because both concrete and steel reinforcement are rate-sensitive materials, the RC beam-column joints are bound to behave differently under different strain rates. This paper describes an investigation of seismic behavior of RC beam-column joints which are subjected to large cyclic displacements on the beam ends with three loading velocities, i.e., 0.4 mm/s, 4 mm/s and 40 mm/s respectively. The levels of strain rate on the joint core region are correspondingly estimated to be $10^{-5}/s$, $10^{-4}/s$, and $10^{-2}/s$. It is aimed to better understand the effect of strain rates on seismic behavior of beam-column joints, such as the carrying capacity and failure modes as well as the energy dissipation. From the experiments, it is observed that with the increase of loading velocity or strain rate, damage in the joint core region decreases but damage in the plastic hinge regions of adjacent beams increases. The energy absorbed in the hysteresis loops under higher loading velocity is larger than that under quasi-static loading. It is also found that the yielding load of the joint is almost independent of the loading velocity, and there is a marginal increase of the ultimate carrying capacity when the loading velocity is increased for the ranges studied in this work. However, under higher loading velocity the residual carrying capacity after peak load drops more rapidly. Additionally, the axial compression ratio has little effect on the shear carrying capacity of the beam-column joints, but with the increase of loading velocity, the crack width of concrete in the joint zone becomes narrower. The shear carrying capacity of the joint at higher loading velocity is higher than that calculated with the quasi-static method proposed by the design code. When the dynamic strengths of materials, i.e., concrete and reinforcement, are directly substituted into the design model of current code, it tends to be insufficiently safe.

• Bulletin of the Korean Chemical Society
• /
• v.5 no.2
• /
• pp.73-78
• /
• 1984

Superplastic alloys generally exhibit a three-stage sigmoidal variation of stress (f) with strain rate (s), the stages being named region 1, 2 and 3 according to the increasing order of stress or strain rate. In the recent years, two different types of papers have been published on the plastic deformation of Zn-22% Al eutectoid in region Ⅰ differing in strain-rate sensitivity m (= dln f/dln s). In this paper, the data of the two groups have been analysed by applying Kim and Ree's theory of superplastic deformation. (1) We obtained the parametric values of $X_{gj}/{\alpha}_{gj}\;and\;{\beta)_{gj}$ (g: grain boundary, j = 1,2 indicating flow units) appearing in Kim and Ree's theory [Eq. (2a)]. (2) It was found that the value of $X_{g^2}/{\alpha}_{g^2}$ is small for the group data with small m, i.e., ${\alpha}_{g^2}$, which is proportional to the size of flow unit g2, is large whereas ${\alpha}_{g^2}$ is small for the groups data with large m, i.e., the size of the flow unit g2 is small. In other words, the two types of behavior occur by the size difference in the flow units. (3) From the ${\beta}_{gj}$ value, which is proportional to the relaxation time of flow unit gj, the ${\Delta}H_{gj}^{\neq}$ for the flow process was calculated, and found that ${\Delta}H_{g^2}^{\neq}$ is large for the group data with small m whereas it is small for the group data with large m. (4) The flow-unit growth was studied, but it was concluded that this effect is not so important for differentiating the two groups. (5) The difference in ${\alpha}_{g^2}$ and in the growth rate of flow units is caused by minute impurities, crystal faults, etc., introduced in the sample preparation.

• International Journal of Highway Engineering
• /
• v.7 no.2 s.24
• /
• pp.69-76
• /
• 2005

While the repeated traffic loading accumulates the damage of asphalt pavement, the damage has being healed during rest periods. And then, this healing enhances the fatigue life of asphalt pavement. A method was developed to determine the healing rate of asphalt mixture in terms of recovered dissipated creep strain energy (DCSE) per unit time, and the healing properties of four different asphalt mixtures were evaluated. The test procedure consists of repeated loading test and periodical resilient modulus tests. A normalized healing rate in terms of $DCSE/DCSE_{applied}$ was defined to evaluate the healing properties independently of the amount of damage incurred in the mixture. From the test results, it was concluded that the healing rates of asphalt mixtures were increased exponentially as the temperature was increased and more affected by the structural characteristics of mixture such as asphalt content than the binder characteristics such as the polymer modification.