• Journal of Welding and Joining
• /
• v.33 no.4
• /
• pp.44-49
• /
• 2015

The structural epoxy adhesive used in car body assembly needs the highest level of joint mechanical strength under lap shear, T-peel and impact peel conditions. In this study, the effect of nano functionalized block copolymer addition on the impact peel strength of epoxy adhesive was investigated. DSC analysis showed that the addition of nano functionalized block copolymer did not affect the curing reaction of epoxy adhesive. From single lap shear test, it was found out that the addition of nano functionalized block copolymer slightly decreased the cohesive strength of cured adhesive layer. The addition of nano functionalized block copolymer showed beneficial effect on T-peel strength by changing the adhesive failure mode to the mixed mode. However, the addition of nano functionalized block copolymer just decreased the room temperature impact peel strength. It was considered that the addition of nano functionalized block copolymer could have effect on disturbing the crack propagation only for the case of slow strain rate.

• Journal of Korean Society of Steel Construction
• /
• v.11 no.1 s.38
• /
• pp.33-42
• /
• 1999

In the present study, crack initiation criteria, static failure and tensile mode fatigue behavior for a rail steel are evaluated to assure the railway vehicle's safety. The transverse fissure, which is the most critical damage in the rail, is initiated by the maximum shear stress and its location is subsurface. In addition, the possibility of transition from the shear mode to the mixed mode increases with increasing the length of subsurface crack. Because of the brittleness by the welding, the fracture toughness of the welded part is lower than of the base metal. For low ${\Delta}K$, the stage II fatigue crack growth rates of the welded part is slower than of the base metal but, for high ${\Delta}K$, this different behavior for fatigue crack growth rate is nearly diminished. These trends are more remarkable for low stress ratio, R=0.1. It is believed that this behavior is caused by the change of the microstructure which that of the welded part is coarser than of base metal.

• Structural Engineering and Mechanics
• /
• v.74 no.6
• /
• pp.723-735
• /
• 2020

This study is reported the adhesion failure in adhesive bonded composite and specifically for the T-joint structure. Three-dimensional finite element analysis has been performed using a commercial tool and the necessary outcomes are obtained via an eight noded solid element (Solid 185-element) from the library of ANSYS. The structural analysis input has been incurred through ANSYS parametric design language (APDL) code. The normal and shear stress distributions along different layers of the joint structure have been evaluated as the final outcomes. Based on the stress distributions, failure location in the composite joint structure has been identified by using the Tsai-Wu stress failure criterion. It has been found that the failure index is maximum at the interface between flange and web part of the joint (top layer) which indicates the probable location of failure initiation. This kind of failures are considered as adhesion failure and the failure propagation is governed by strain energy release rate (SERR) of fracture mechanics. The different adhesion failure lengths are also considered at the failure location to calculate the SERR values i.e. mode I fracture (opening), mode II fracture (sliding) and mode III fracture (tearing) along the failure front. Also, virtual crack closure technique (VCCT) principle of fracture mechanics steps is used to calculate the above said SERRs. It is found that the mode I SERR is more dominating compared to other two modes of failure for the joint considered. Finally, the influences of various parametric (geometrical and material) effect on SERR of the joint structure are evaluated and discussed in details.

• Korean Journal of Food Science and Technology
• /
• v.45 no.2
• /
• pp.252-256
• /
• 2013

We tested the possibility of utilizing Korea domestic wheat (winter wheat variety "keumkangmil") as a source of vinegar production. After saccharification of the whole-wheat flour with wheat malt, the saccharized liquid undergoes alcoholic fermentation, followed by acetic fermentation. Acetic acid bacterium A8, which showed the highest acetic acid production (4.56%) with domestic wheat as substrate, was selected from conventional vinegars. The strain A8 was identified as Acetobacter pasteurianus A8 through phylogenetic study using 16S rDNA sequencing analysis. The optimal condition for the malt enzyme was found to be $15^{\circ}C$ for germination periods of 6 days; its amylase activity was 608.4 U. Acetic acid production from domestic wheat substrate supplemented with 5% ethyl alcohol reached 5.8% after 24 days of static fermentation at $30^{\circ}C$ with a seeding rate of 5%.

• Korean Journal of Microbiology
• /
• v.52 no.3
• /
• pp.298-305
• /
• 2016

Previously our laboratory showed that Pseudomonas alkylphenolica KL28 possesses two different lap and pcu gene clusters for p-cresol catabolism. In this study, additional gene cluster (pchACXF-pcaHG-orf4-pcaBC) has been identified to encode enzymes necessary for catabolism of p-cresol to ${\beta}$-carboxy-cis,cis-muconate. This gene cluster showed almost identical nucleotide sequence homologies to those in the plasmid of Pseudomonas putida NCIMB 9866 and 9869, British origins, indicating the possibility of a horizontal gene transfer. Through mutagenesis of each gene cluster and gfp-based promoter reporter assays, it has been shown that the three gene clusters are functionally operated and pch genes are induced by p-cresol. Furthermore, the pcu gene cluster of the three was shown to be dominantly expressed in utilization of p-cresol. Mutation of the pcu gene was defective in aerial structure formation under p-cresol vapor, indicating the utilization rate of carbon source is one of key elements for the multicellular development of this strain.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.1
• /
• pp.24-27
• /
• 2011

Effect of substitution of Mn for Ni on transformation behavior, shape memory characteristics and superelasticity of Ti45Ni-5Cu alloy has been investigated by means of electrical resistivity measurements, X-ray diffraction, thermal cycling tests under constant load and tensile tests. The one-stage B2-B19' transformation occurred when Mn content was 0.5 at%, above which the two-stage B2-B19-B19' transformation occurred. A temperature range where the B19 martensite exists was expanded with increasing Mn content because decreasing rate of Ms (60 K / % Mn) was larger than that of Ms' (40 K / % Mn). Ti-(45-x)Ni-5Cu-xMn alloys were deformed in plastic manner with a fracture strain of 60 % ~ 32 % depending on Mn content. Clear superelasticity was found in fully annealed Ti-(45-x)Ni-5Cu-xMn alloys with Mn content more than 1.0 at%, which was ascribe to a solid solution hardening by substitution of Mn for Ni.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.5
• /
• pp.349-355
• /
• 2016

Divinycell, which functions as both insulation and a supporting structure, is generally applied in the NO96-type liquefied natural gas (LNG) insulation system. Polymer-material-based Divinycell, which has a high strength and low weight, has been widely used in the offshore, transportation, wind power generation, and civil engineering fields. In particular, this type of material receives attention as an insulation material because its thermal conductivity can be lowered depending on the ambient temperature. However, it is difficult to obtain research results for Divinycell, even though the component materials of the NO96-type LNG cargo containment system, such as 36% nickel steel (invar steel), plywood, perlite, and glass wool, have been extensively studied and reported. In the present study, temperature and strain-rate dependent compressive tests on Divinycell were performed. Both the quantitative experimental data and elastic recovery are discussed. Finally, the mechanical characteristics of Divinycell were compared to the results of polyurethane foam insulation material.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.53-59
• /
• 2021

Purpose & Method: The purpose of this study is the theoretical study on the durability standard of ground structures monitoring sensors. A survey on the durability criteria for construction monitoring sensors of domestic construction companies and the income tax implementation regulations, the standard years of contents such as buildings and the standards of the Public Procurement Service for construction monitoring and construction machinery were analyzed. Result: The durability criterion such as the inclination meter and the strain gauge, which are purchased from the Public Procurement Service prior to installation on the ground structure, is 8 to 10 years. Conclusion: The actual durability analysis by comparing the reliability of various monitoring sensors installed in dams at home and abroad, As a result of comprehensive study on the loss and damage rate of the maintenance monitoring sensor installed in the tunnel, the proper durability period of the built-in type monitoring sensor such as domestic pore pressure meter and earth pressure meter installed in the structure or the ground is 5 to 8 years it seems reasonable.

• Research in Plant Disease
• /
• v.27 no.4
• /
• pp.164-171
• /
• 2021

In August 2020, 377 anthracnose strains were isolated from anthracnose-infected peppers collected from 25 farms in Sunchang-gun, Jeollabuk-do. Inhibition rate of mycelial growth of 11 pepper anthracnose fungicides registered in Korea was investigated for 62 strains selected by region and the degree of susceptibility to each fungicide was investigated. As a result of the fungicide susceptibility test of anthracnose to the fungicide, no resistant strains were observed in fluazinam, prochloraz manganese, and benomyl, but resistant strains appeared in at least three areas for other fungicides, and all strains in all regions were resistant to dithianon. Through this, it was confirmed that the fungicide resistance was expressed in the strain group due to the continuous treatment of the fungicide in some areas. By region, resistant strains to seven pesticides appeared in Sunchang-eup and Paldeok-myeon, and resistant strains to six pesticides appeared in Geumgwa-myeon, Bokheung-myeon, Ssangchi-myeon, Yudeung-myeon, and Pungsan-myeon. There was no significant correlation between fungicide registration time and emergence of resistant strains.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.3
• /
• pp.121-127
• /
• 2024

We investigate the effect of T6 heat treatment on the microstructure and mechanical properties of AA365 (Al-10.3Si-0.37Mg-0.6Mn-0.11Fe, wt.%) alloy fabricated by vacuum-assisted high pressure die casting by means of thermodynamic calculation, X-ray diffraction, scanning and transmission electron microscopy, and tensile tests. The as-cast alloy consists of primary Al (with dendrite arm spacing of 10~15 ㎛), needle-like eutectic Si, and blocky α-AlFeMnSi phases. The solution treatment at 490 ℃ induces the spheroidization of eutectic Si and increase in the fraction of eutectic Si and α-AlFeMnSi phases. While as-cast alloy does not contain nano-sized precipitates, the T6-treated alloy contains fine β' and β' precipitates less than 20 nm that formed during aging at 190℃. T6 heat treatment improves the yield strength from 165 to 186 MPa due to the strengthening effect of β' and β' precipitates. However, the β' and β' precipitates reduce the strain hardening rate and accelerate the necking phenomenon, degrading the tensile strength (from 290 to 244 MPa) and fracture elongation (from 6.6 to 5.0%). Fractography reveals that the coarse α-AlFeMnSi and eutectic Si phases act as crack sites in both the as-cast and T6 treated alloys.