• Korean Journal of Medicinal Crop Science
• /
• v.19 no.3
• /
• pp.170-176
• /
• 2011

This study was carried out to investigate whether Chrysanthermum zawadskii var. latilobum Kitamura (C. zawadskii) extracts has an inhibitory effect against the mutagenicity by cigarette smoke condensates (CSC). C. zawadskii was extracted with 70% ethanol and the yield was 18.5%. We further fractioned 70% ethanol extract sequentially to diethylether, chloroform, dichloromethane, and aqueous water, and gained the yield of 17.5%, 5.6%, 5.8%, 32.8% and 35.5%, respectively. In the Ames test, there was no mutagenic effect of crude extract and its solvent fractions up to 2 mg/plate toward Salmonella typhimurium TA 98 with or without S-9 mix metabolic activations. On the contrary, the crude extract showed an inhibitory activity against the mutagenicity of CSC in the presence of S-9 mix metabolic activation. Diethyl ether layer among five solvent fractions showed the highest inhibitory activity. The inhibitory activity of diethyl ether fraction was also increased in a dose-dependent manner and the inhibitory rate was about 97.7% at the concentration of 1 mg/plate. In this study, we conclude that crude extract of C. zawadskii itself is potentially safe for mutagenicity, and the diethyl ether fraction has an inhibitory effect against the mutagenicity of CSC.

• Nuclear Engineering and Technology
• /
• v.50 no.1
• /
• pp.182-189
• /
• 2018

A neutron generation system was developed to induce fissile fission in a lead slowing down spectrometer (LSDS) system. The source neutron is one of the key factors for LSDS system work. The LSDS was developed to quantify the isotopic contents of fissile materials in spent nuclear fuel and recycled fuel. The source neutron is produced at a multilayered target by the (e,${\gamma}$)(${\gamma}$,n) reaction and slowed down at the lead medium. Activation analysis of the target materials is necessary to estimate the lifetime, durability, and safety of the target system. The CINDER90 code was used for the activation analysis, and it can involve three-dimensional geometry, position dependent neutron flux, and multigroup cross-section libraries. Several sensitivity calculations for a metal target with different geometries, materials, and coolants were done to achieve a high neutron generation rate and a low activation characteristic. Based on the results of the activation analysis, tantalum was chosen as a target material due to its better activation characteristics, and helium gas was suggested as a coolant. In addition, activation in a lead medium was performed. After a distance of 55 cm from the lead surface to the neutron incidence, the neutron intensity dramatically decreased; this result indicates very low activation.

• Proceedings of the Botanical Society of Korea Conference
• /
• 1999.07a
• /
• pp.45-49
• /
• 1999

Plant cell culture is emerging to express bioactive foreign proteins because it has several advantages in that it is safe, economical, genetically stable and eukaryotic expression system comparing with other expression systems. However several limitations such as slow growth rate, low expression level and lack of well established down stream process need to be answered. As a preliminary approach to produce the immunologically interested molecules through the plant cell culture, we tested if granulocyte-macrophage colony stimulating factors (GM-CSFs) from both murine (mGM-CSF) and human (hGM-CSF) are produced as a biologically active form through plant cell culture. The murine and human GM-CSF genes were cloned into the plant expression vector, pBI121, and Ti-plasmid mediated transformation of tobacco leaves was conducted using Agrobacterium tumefaciens harboring both recombinant GM-CSF (rGM-CSF) genes. Cell suspension culture was established from the leaf-derived calli of transgenic tobacco plant. Northern blot analysis indicated the expression of the introduced mGM-CSF gene in both transgenic plant and cell suspension cultures. In addition, the biological activities of both murine and human GM-CSF from plant cell culture were confirmed by measuring the proliferation of the GM-CSF dependent FDC-PI and TF-1 cells, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.4
• /
• pp.1035-1038
• /
• 2013

Rolling circle amplification (RCA) of DNA on an aligned-carbon nanotube (a-CNT) surface was electrically interfaced by the a-CNT based filed effect transistor (FET). Since the electric conductance of the a-CNT will be dependent upon its local electric environment, the electric conductance of the FET is expected to give a very distinctive signature of the surface reaction along with this isothermal DNA amplification of the RCA. The a-CNT was initially grown on the quartz wafer with the patterned catalyst by chemical vapor deposition and transferred onto a flexible substrate after the formation of electrodes. After immobilization of a primer DNA, the rolling circle amplification was induced on chip with the a-CNT based FET device. The electric conductance showed a quite rapid increase at the early stage of the surface reaction and then the rate of increase was attenuated to reach a saturated stage of conductance change. It took about an hour to get the conductance saturation from the start of the conductance change. Atomic force microscopy was used as a complementary tool to support the successful amplification of DNA on the device surface. We hope that our results contribute to the efforts in the realization of a reliable nanodevice-based measurement of biologically or clinically important molecules.

• Nuclear Engineering and Technology
• /
• v.17 no.2
• /
• pp.116-128
• /
• 1985

Considering vacancy generation and migration in grain and sink at grain boundary, a mechanistic densification model which is dependent on UO$_2$ temperature and microstructure has been developed. This densification model is a function of time, fission rate, temperature, density, pore size distribution and grain size. The resultant equation derived in this model which is different from Assmann and Stehle's resultant equations for four temperature regions, can be applied directly for all the pellet temperatures. The predictions of the present densification model very well agreed with the experimental data. This model well predicts absolute magnitude and trend in comparison with the empirical algorithm used in KFEDA code.

• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.141-147
• /
• 2016

Staphylococcus aureus cultures exposed to rotating magnetic field (RMF) were studied in order to analyse the possible induced changes in staphylococcal enterotoxin genes (se) expression. Liquid cultures of S. aureus strains carrying different se were exposed to the RMF of magnetic frequency 50 Hz and magnetic induction 34 mT for 10 h at $37^{\circ}C$. Three time points of bacterial growth cycle were considered for RNA extractions. Gene expression analyses were evaluated using real-time quantitative PCR method. The present study confirmed, that the RMF can stimulate the growth rate of S. aureus cultures in comparison to the unexposed controls, while the stimulation is not strain dependent. The studies have also shown, that the RMF, depending on the exposure time but regardless the bacterial strain, can influence on the expression of various se. In general, except for sea, as a result of bacterial exposure to the RMF through subsequent growth phases, the expression of se decreased, reaching the values below results recorded for unexposed controls. In the case of sea expression remained at a lower level as compared to the control, regardless the time of exposition.

• Journal of Welding and Joining
• /
• v.29 no.4
• /
• pp.54-60
• /
• 2011

Adhesive bonding is one of the most promising joining methods which may substitute for conventional metallurgical joining processes, such as welding, brazing and soldering. Curing behavior and mechanical properties of adhesive joint are largely dependent on the curing agent including hardener and catalyst. In this study, effects of curing system on the curing behavior and single-lap shear strength of epoxy adhesive joint are investigated. Dihydrazide, anhydride and dicyandiamide(DICY) were chosen as hardener and imidazole and triphenylphosphine(TPP) were chosen as catalyst. In curing behavior, TPP showed the delay of the curing rate for DICY and ADH at $160^{\circ}C$, compared to imidazole catalyst due to the high curing onset/peak temperature. DICY seemed to be most beneficial in the joint strength for both steel and Al adherends, although the type of adherends affected the shear strength of epoxy adhesive joint.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1493-1500
• /
• 2001

Recently small punch creep testing (or miniature disc bend creep test) has received much attention through European collaborative research projects. This method was considered as a substitute for the conventional creep rupture testing by which the residual creep life is measured from the specimen taken out from serviced components of high temperature plants. It would be beneficial if the material creep properties such as power law creep constants as well as the creep rupture life can be measured from the small punch creep test. In this paper a method of assessing creep constants from the small punch creep testing is proposed. Finite element analyses were performed to investigate evolution of stress and strain rate at the weakest locations of the small punch creep specimen. Elastic-plastic-secondary creep analyses were carried out. The estimation equations for creep constants by the small punch creep testing are proposed based on the finite analysis results. Small punch creep tests were also performed with 9Cr steel and the accuracy of the proposed equation was verified by the experimental results.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.2
• /
• pp.175-182
• /
• 2010

The purpose of this study was to evaluate the biomechanical effect of sports taping on the lower limb during drop landing. Twelve male university students who have no musculoskeletal disorder were recruited as the subjects. Principal strain, median frequency, vertical GRF, loading rate, angular velocity and resultant joint moment were determined for each trial. For each dependent variable, paired t-test was performed to test if significant difference existed between taped and untaped conditions(p<.05). The results showed that principal strain of the thigh and the shank in taping group were significantly less than those found in control group. These indicated that sports taping may prevent excessive mechanical strain caused by impact force during the deceleration phase. Flexion(-)-extension(+) and varus(-)-valgus(+) resultant joint moment of the knee joint in taping group were greater than corresponding value for control group. It seems that extensor muscle of the knee joint were not only supported by sports taping during knee flexion but also sports taping is effective for minimizing the possibility of injury.

• Journal of the Korean Home Economics Association
• /
• v.36 no.1
• /
• pp.65-79
• /
• 1998

The purposes of this study were to establish a conceptual model on the woman's labor force participation and mobility in the labor market and to analyze the correlation between them. Included in those models were two independent variable sets. The one was related to household's financial conditions and the other was associated to the woman's role such as marital status, the number of children and the existence of young children. KHPS's national data was used and the Binomial Probit Model and Bivariate Probit Model were employed to analyse the effects of independent variables and the correlations between two dependent variables. The results of this study were as follows. The rate of women's labor force participation and the percentage of mobility willingness were 15.4% and 22.0%. Among the variables which have affected women's labor force participation were total wage income, non-wage income, expenditure on children's education and the subject judgement of their financial status. The existence of children under the age of 6 and marital status had significant influences on women's mobility willingness. The correlation between women's labor force participation and mobility willingness was very significant statistically. These findings clarified the status of woman as a secondary worker and pointed that a woman's economic activity would be subject to the woman's condition rather than her human capital.