• 제목/요약/키워드: railway steel bridge

검색결과 219건 처리시간 0.028초

PC-Slab 합성 철도판형교 유도상화 시험부설에 따른 성능 비교평가 (Capacity evaluation of PC-slab composite actions for the railway steel plate girder according to an experimental construction)

  • 민경주;이성욱;최형수;우용근
    • 한국철도학회:학술대회논문집
    • /
    • 한국철도학회 2011년도 춘계학술대회 논문집
    • /
    • pp.697-706
    • /
    • 2011
  • There are more than 800 railway steel plate girder bridges which are in use and the total length is approximately 50 km. Among these, it shall be pointed out that non-ballast rail systems which lay on wood sleepers are the most critical members. To strengthen this type of structures, mainly two methods have been applied. The first one is the most typical method which is to replace the girders with slab girder system or steel composite girders and to add ballast. It is not uncommon that the construction cost of substructure is more than ten time higher than that of superstructures and even in this case, the structural uncertainty for the substructures is not diminished. To resolve above mentioned problems, new method was developed to rehabilitate railway steel girder bridge by adding PC-slab using transport equipment. Using this method, substructure strengthen is rarely required because the additional weight to the bridge superstructure is only up to 1.0t/m. Also it was possible to save the construction cost by reducing construction duration and by simplifying the construction process. Experimental construction was performed for Jewon bridge and measurements were performed before and after construction to verify the bridge capacity.

  • PDF

강철도교 열화현상에 관한 보수/보강 연구 -강철도교의 플랜지 용접이음부의 거동 특성 및 피로균열 보수보강- (A Study on Repair/ Retrofit for Deteriorations of Steel Bridge -Behavior Characteristics of Welded Joint Part of Flange and Repair/Retrofit of Fatigue Crack in Railway Steel Bridge-)

  • 경갑수;이성진;박진은;차철준
    • 한국강구조학회 논문집
    • /
    • 제24권6호
    • /
    • pp.613-625
    • /
    • 2012
  • 철도교는 일반적으로 설계하중에 근접한 열차하중이 빈번하게 통과할 가능성이 있으므로, 초기설계단계부터 여러 구조상세에 대해 피로특성을 충분한 반영하는 것이 필요하다. 그럼에도 불구하고 철도교에 작용하는 축하중의 크기 및 배치 특성, 피로에 대한 부적절한 구조상세의 적용 등으로 인하여 강철도 플레이트거더교에서 부분적으로 피로균열이 보고되고 있다. 상부플랜지와 복부의 용접이음부에서의 피로균열의 주요 발생 원인의 하나는 침목을 지지하는 주거더와 열차하중이 작용되는 레일과의 중심간격 차이에 따른 열차하중의 편심작용에 의한 것이다. 이 연구에서는 공용중인 강철도 상로플레이트거더교를 대상으로 현장조사 및 현장계측, 일련의 구조해석을 실시하고, 대상교량의 구조거동 특성 및 피로균열의 발생 원인의 규명, 보수 보강(안)에 대하여 검토하였다.

당산철교의 설계 (Design of Dang-San Steel Railway Bridge)

  • 유동호;김선일
    • 전산구조공학
    • /
    • 제12권4호
    • /
    • pp.69-69
    • /
    • 1999
  • Design of Dangsan Steel Railway Bridge(a part of Seoul Subway Line NO. 2), which is supposed to be replaced after its 15years survice, was done, and the reconstruction has begun in Dec. 1997. The design include new superstruc-ture and bridge piers, retrofitting of the foun-dation, rail system, electric and signal, etc. In this paper, design of the structure is mainly summarized. The main span superstructure, across Han river, is composite section which is com-posed of steel box and reinforced concrete deck slab with 9 span continuous. The superstructure for the approaches is bottom througth type 2-cell steel box girder with steel floor system and concrete deck slab with 3 or 4 span continuous. The bridge piers was planned to be reconstructed based upon the result from the various investi-gations, while the foundation(cassion and pile foundation) was planned to be retrofitted. For superstructure erection, the method of combination of barge bent and heavy lifting and the launching truss method was investigated for the main span and approach spans, respectively.

  • PDF

강상형 철도교의 도상종류와 형고에 따른 동특성 및 안정성 연구 (Study on Dynamic Characteristic and Safety of 45m Steel Box Railway Bridge according to Girder hight and Ballast)

  • 윤지홍;최권영;권구성;안주옥;정원석
    • 한국철도학회:학술대회논문집
    • /
    • 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
    • /
    • pp.3147-3155
    • /
    • 2011
  • Railway bridges are highly susceptible to resonance due to the equidistant axle load with constant speed of train. Thus, it is inevitable verify dynamic characteristics and quantities against dynamic guidelines. Recently, various new-type bridges are developed and applies to medium span length between 30m and 40m. However, just steel box girder bridge is under review for span length between 45m and 50m without development any new technologies. This study investigate the dynamic properties and safety of steel box railway bridge having span length 45m in alternative girder hight and kind of ballast. Numerical analysis is performed time series analysis by mode superposition using calculated natural vibration frequency and mode after carry out a free vibration analysis and extract modal parameter to higher modes. The results are then compared to various dynamic stability standards toward target bridge's dynamic stability analysis. The result of this study is expected as a reference for design railway bridges.

  • PDF

소수주형 철도교의 궤도시스템 변화에 따른 동적거동 분석 (A Dynamic Behavior Analysis of composite Few Plate Girder Railway Bridge under Variety of Track systems)

  • 이홍준;최정열;엄맥;박용걸
    • 한국철도학회:학술대회논문집
    • /
    • 한국철도학회 2005년도 추계학술대회 논문집
    • /
    • pp.1171-1176
    • /
    • 2005
  • The latest technical development of steel plate girder railway bridge are developing in ways to maximize its durability of materials in use of high strength steel and efficiency of maintenance and management by the introduction of simplified and standardization ideas. In addition to this, it is also expected to reduce the cost of bridge construction and to simplify the process of bridge manufacturing. Referring to this, composite few plate girder railway bridge is highly recommendable that is very economical with the fine exterior. In this paper, it will analyse the variation of dynamic behavior of existing composite few plate girder railway bridge with ballast caused by modified Slab Track through interpretation of limited enzyme in order to obtain the existing data for improvement of Slab Track system from Ballast Track system. Consequently, it can help maximize economic efficiency and structural capability. As a results, although the natural frequency by modified Slab Track are decreased, it is hardly influencing on the safety of railway bridges. It is also evident in the case of slab deck with a reduced scale in comparison with Ballast Track. Therefore, it is expected to reduce the cost of a railway bridge plan. And, it can expect the synergistic effect of the ensure long term durability of bridge caused by decreased stresses of bottom flange due to reduced dead load. As a result, the analytical study are carried out to investigate the composite few plate girder railway bridge could be the optimal design method for the dynamic safety of a girder section.

  • PDF

Full-scale 실험 모드해석을 이용한 노후화된 철도판형교의 진동특성 (Vibrational Characteristics of the Deteriorated Railway Plate Girder Bridge by Full-scale Experimental Modal Analysis)

  • 김주우;정희영
    • 한국강구조학회 논문집
    • /
    • 제24권1호
    • /
    • pp.119-128
    • /
    • 2012
  • 본 연구에서는 실험적 모드해석 기법을 이용하여 외부환경에 직접 노출되어 있는 실제 철도판형교의 full-scale 동적 테스트가 수행되었다. 충격해머 모드실험에 의해 얻어진 철도판형교의 모드 매개변수를 유한요소해석으로부터 구한 고유진동수와 모드형상과 비교, 분석하였다. 실험적 모드해석에 의해 측정된 실험 데이터와 해석적 진동분석에서 얻어지는 출력만의 데이터를 교량 부재의 기하학적 특성 및 재료적 특성을 다양하게 고려하여 모델보정 테크닉에 적용하였다. 철도판형교의 실험적 모드해석 결과를 검증하기 위한 유한요소모델이 모드인식 기법을 이용하여 보정되었다. 실험 데이터와 유한요소해석 기준모델의 모델보정과정의 결과와 함께 부재특성의 변화를 통하여 이루질 수 있는 손상평가에 대한 기초적 데이터베이스가 제공된다.

Behavior of Bridge Bearings for Railway Bridges under Running Vehicle

  • Choi, Eun-Soo;Yu, Wan-Dong;Kim, Jin-Ho;Park, Sun-Hee
    • International Journal of Railway
    • /
    • 제5권1호
    • /
    • pp.10-21
    • /
    • 2012
  • Open steel plate girder (OPSG) bridges are the most prevalent railroad bridge type in Korea, constituting about 40% of all railroad bridges. Solid steel bearings, known as line type bearings, are placed in most OSPG railway bridges. However, the line type rigid bearings generate several problems with the bridge's dynamic behavior and maintenance in service. To compare and investigate the dynamic behaviors of line type, spherical and disk bearings, the vertical displacements of each bearing, including fixed and expansion type, under running vehicles are measured and analyzed. The displacements of disk and spherical bearings are measured after replacing the line type bearings with spherical and disk bearings. This study also analyzed dynamic behaviors of bridges. Furthermore, the deformation of the PTFE (Polytetrafluoroethylene) plate that is placed inside of expansion type spherical and disk bearings is measured and its effect on the dynamic behavior of the bridges is discussed. The up-lift phenomenon at the bearings installed for the steel bridges is estimated. The vertical displacements at mid-span of the bridges are compared according to the bearing types. Finally, the 1st mode natural frequencies are estimated, and the relationship to the vertical displacement is discussed.

국내최장 고속철도 정지고가(L=9.3km) 교량형식 개발 및 설계 - 35m PSM PSC Box교, 80m 3경간 Arch교, 국내최초 ED교 - (The Planning and Design of Jeong-Ji High Speed Railway Bridge)

  • 장인호;박경호;박종화;김영남;김선필
    • 한국철도학회:학술대회논문집
    • /
    • 한국철도학회 2010년도 춘계학술대회 논문집
    • /
    • pp.1691-1696
    • /
    • 2010
  • Jeong-Ji overbridge is designed to be 9.3km long, the longest for a high speed railway bridge ever constructed in Korea. This bridge is constituted of three types of structure. Standard type bridge is 35m PSC Box bridge which will be constructed by Precast Span Method. To cross the Cheonan Nonsan Expressway, 80m three-span steel arch bridge is designed to avoid rail expansion joint. Finally, Extradosed bridge is planned for high speed railway bridge for the first time in Korea based on originative and advanced design techniques. It is expected that this will contribute to the development of national technology for long-span high speed railway bridges.

  • PDF

무도상 판형교의 횡방향 동적거동특성 분석을 위한 실험적 연구 (Field Test to Investigate Lateral Dynamic Characteristics of Steel Plate Girder Railway Bridge without Ballast)

  • 오지택;김현민;박옥정;박찬
    • 한국철도학회:학술대회논문집
    • /
    • 한국철도학회 2003년도 추계학술대회 논문집(II)
    • /
    • pp.591-595
    • /
    • 2003
  • Field measurements were conducted to analysis lateral dynamic characteristics of existing steel plate girder railway bridges without ballast. Three bridges which have 9m, 12m, 18m span length in Kyoung-Bu Line were selected for test. According to the each bridge, dynamic lateral deflections and accelerations were measured. From the present study, it was observed that dynamic lateral amplification phenomena caused by a fluctuation of lateral force were occurred under the current running circumstances. Lateral deflections were occurred below than that specified in Korean railway bridge specification, but lateral accelerations is a match for vertical accelerations. From now on, it is in need a plan to reduce lateral accelerations for the conventional railway Line speed up.

  • PDF

TDD기법을 이용한 고속철도 교량의 동특성 추출 (Extracting Modal Parameters of Railway Bridge under the Action of High-speed Train Using TDD Technique)

  • 김병화
    • 한국강구조학회 논문집
    • /
    • 제20권6호
    • /
    • pp.761-771
    • /
    • 2008
  • 열차운행주파수가 철도교의 고유진동수와 일치하면, 철도교의 공진은 피할 수 없다. 또한, 열차가 교량을 매우 빠르게 통과하면, 계측 가능한 시간응답의 샘플 수는 매우 적다. 본 논문은 그러한 경우에 대하여 철도 교량의 동특성을 매우 효과적으로 추출할 수 있는 TDD기법과 SI기법을 소개한다. 열차통과 직후에 교량의 자유진동 시간응답구간의 상호상관을 이용하여 모드형상은 TDD기법으로 추출하고, 고유진동수 및 감쇠비 등의 시간변수들은 SI기법으로 추출한다. 경부고속철도 시스템에 위치한 2경간 강합성교량의 동특성 추출실험을 통하여 TDD기법과 SI기법의 현장 적용성이 검토되었다. 동특성 추정결과는 기존의 ERADC기법의 결과와 비교 검토되었다. 추정결과는 기존의 방법을 이용하여 획득된 결과와 매우 잘 일치한다.