• Proceedings of the KIEE Conference
• /
• 2001.05a
• /
• pp.251-253
• /
• 2001

This paper presents a fault location algorithm for distribution feeder systems. Distribution feeders include single phase and three phase laterals. The proposed algorithm achieves a high accuracy by continuously updating voltage and current phasor using the symmetrical components and admittance load model.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1422-1424
• /
• 1999

This Paper Presents a efficient algorithm for loss reduction of distribution system by automatic sectionalizing switch operation in distribution systems of radial type. To apply tabu search to reconfiguration of distribution system, in this Paper we Propose the several move methods and efficient reconfiguration procedure. We also discuss the tabu search techniques of diversifying the search of solution space as well as the simple tabu search. The experimental results show that the proposed tabu search techniques have the ability to search a good solution.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.9-15
• /
• 2016

Distribution networks are operated in radial fashion during the normal state. Loop configuration is also required temporally in case of live load transfer among the adjacent feeders. Voltage angles of each substation buses are very important data in order to calculate power flow of the loop structured distribution feeders. This paper proposes substation bus voltage angle calculation method using voltage angle difference measured at the normally open tie switches. Simulation case studies using Matlab simulink have been performed to establish feasibility of proposed method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.218-224
• /
• 1999

It is necessary to improve mechanical and optical properties in the optical disk substrates as the information storage devices with high storage density using short wavelength laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates with high is regarded as the most suitable process to manufacture optical disk substrates with high dimensional accuracy low residual stresses and superb optical properties In the present study polycarbonate optical disk substrates were fabricated by injection compression molding and the birefringence regarded as one of the most important optical properties for optical disk is measured. The effects of various processing conditions upon the development of birefringence distribution were examined experimentally. It was found that the value of the birefringence distribution were very sensitive to the mold wall temperature history and the variance of the birefringence distribution in the radial direction was affected by the level of the packing and the compression pressure.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.401-403
• /
• 2001

This paper describes a power flow method for distribution systems, applying the method of symmetrical component to back/forward sweep method. The proposed algorithm is effective for unbalanced radial distribution system, with process of AVR(Auto Voltage Regulator), shunt capacitor. The proposed method was compared with the conventional Back/forward sweep method by using three phase unbalanced distribution systems of 123 nodes.

• Journal of Powder Materials
• /
• v.10 no.3
• /
• pp.201-208
• /
• 2003

Distributions of diamond particles protruding on the surface of worn diamond segments in circular saw has been investigated. Scanning electron microscope was used to examine the worn ,surface and radial saw blade wear and grinding ratio was measured. The number of protruded diamond particle was approximately 50% of the total number of particles, and that was independent of diamond particle concentration and table speed. It was also noted that the inter-particle distance did not follow a symmetric function like Gaussian distribution function, instead it fitted well with a probability density function based on gamma function. The distribution of inter-particle spacing, therefore, was analyzed using a gamma function model.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.86-89
• /
• 1993

This paper contains the various effect of distribution feeder sectionalizing by distribution automation. The effect by automatic sectionalizing switch and the effect by manual switch are analyzed and shown according to the radial feeder and the loop feeder respectively. Based on the reliability analysis, the reference for the feeder division and sectionalization is recommended. Also, the necessary number of manual switch where the automatic switch is installed is recommended through the reliability analysis.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.9-17
• /
• 2002

This analysis is aimed to find out how the conditions of secondary air injection affects the residence time and the turbulence energy of flue gas and flow field in a small incinerator. A commercial code, PHOENICS, is used to simulate the flow field of an Incinerator. The computational grid system is constructed in a cartesian coordinate system In this numerical experiment, an independent numerical variable is the conditions of secondary air injection and dependants are the residence time of flue gas and the mean value of turbulence energy in a primary combustion chamber. The flow field and the distribution of turbulence energy are analysed to evaluate the residence time of flue gas and the turbulence energy The computational results say that the tangential injection of secondary air make the residence time much longer than the radial injection and that the radial injection of secondary make turbulence much stronger than the tangential injection.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.807-812
• /
• 2001

The effects of casing shapes on the interaction of the impeller and volute in a small-size turbo-compressor are investigated. Numerical analysis is conducted for the compressor with circular and single volute casings from inlet to discharge nozzle. In order to predict the flow pattern inside the entire impeller, vaneless diffuser, and casing, calculations with a multiple frame of reference method between the rotating and stationery parts of the domain are carried out. For incompressible turbulent flow fields, the continuity and three-dimensional time-averaged Navier-Stokes equations are employed. To predict the performance of two types of casings, the static pressure and loss coefficients are obtained with various flow rates. Also, static pressure distributions around casings are studied for different casing shapes, which are very important to predict the distribution of radial load.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.2
• /
• pp.13-20
• /
• 1990

The interaction of the flows induced by stator blades with a ship-like wake is discussed to obtain the flow components of each with and without radial shear. The flow induced by stator blades is modeled by lifting line theory and the shear is taken to be provided by the radial gradient of the peripheral mean axial flow approximated by a logarithmic function of radius for a class of vessels. And the theory is based on the linearized Euler equations in the absence of viscosity. The results show that shear effects are relatively large at inner radii and the distribution of blade pitch angles is most effective in reducing non-uniformity.