• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.4
• /
• pp.179-189
• /
• 1999

This study attempts to propose an evaluation considering the property of concrete pore which affects the deterioration of neutralization and the rebar resistance of concrete. Understanding pore property of concrete in using extent, for practical using of concrete manufacturing condition. basic quality property and durability estimation etc, the results of the experiment are as follows. 1) The result of analysis pore property of every specimen with the method of area ratio, in limitation of $10^{-6}{\sim}10^{-5}m$, the pore distribution ratio was maximum. It was high value as W/C was increased and the unit cement content was decreased. 2) In case of using admixture. the volume of pores was some increased as variation of mixing content. In high W/C range, it was very increased compared with plain concrete. 3) Concerned with compressive strength and volume of pores in hardened concrete, it is possible compressive strength estimation using the property of concrete pores. 4) Direct measurement of concrete pore property is difficult. the valuation of the dynamic modulus of elasticity using ultrasonic wave velocity was available. 5) Quantitatively evaluation of concrete structure durability by past result of pore distribution estimation, and it can be estimative scale of property study on the concrete materials.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.1 no.2
• /
• pp.87-94
• /
• 1997

This research aims to develop an algorithm of optimal transducer placement using Kinetic Energy of the structural system. The structural vibration response-based health monitoring is considered one of the best for the system which requires a long-term, continuous monitoring. In its experimental modal testing, however, it is difficult to decide on the measurement locations and their number, especially for complex structures, which have a major influence on the quality of the results. In order to minimize the number of sensing operations and optimize the transducer location while maximizing the accuracy of results, this paper discusses about an optimum transducer placement criterion suitable for the identification of structural damage. As a criterion algorithm, it proposes the Kinetic Energy Optimization Technique (EOT), and then addresses the numerical issues which are subsequently applicable to actual experiment where a bridge model is used. By using the experimental data, it compares the EOT with the EIM (Effective Independence Method) which is generally used to optimize the transducer placement for the damage identification and control purposes. The comparison conclusively shows that the EOT algorithm proposed in this paper is preferable when a structure is to be instrumented with fewer sensors.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.138-144
• /
• 2013

This study is for quality standard establishment of urethane waterproofing membrane method which is mostly applied to waterproofing method for underground parking lot and rooftop. The experiments were carried out on color differences, membrane thickness, tensile property by curing period of liquid urethane before placing protective concrete, and resistance of crack movement according to different substrate surface and reinforcement of non-woven fabric. As a result of experiments, it was found that color differences is increase, membrane thickness is thick, tensile property is low as concrete placing period is shorter. In the fatigue property, membrane thickness of 3 mm was not broken, but 1~2 mm was broken and in the case of the membrane reinforced with non-woven fabric was more stable comparatively non-reinforcement one.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.2
• /
• pp.145-155
• /
• 2002

It is essential for health monitoring of a cable-stayed bridge to provide more accurate and enough information from the sensors. In experimental modal testing, the chosen measurement locations and the number of measurements have a major influence on the quality of the results. The choice is often difficult for complex structures like a cable-stayed bridge. It is extremely important a cable-stayed bridge to minimize the number of sensing operations required to monitor the structural system. In order to obtain the desired accuracy for the structural test, several issues must take into consideration. Two important issues are the number and location of response sensors. There are usually several alternative locations where different sensors can be located. On the other hand, the number of sensors might be limited due to economic constraints. Therefore, techniques such as methodologies, algorithms etc., which address the issue of limited instrumentation and its effects on resolution and accuracy in health monitoring systems are paramount to a damage diagnosis approach. This paper discusses an optimum sensor placement criterion suitable to the identification of structural damage for continuous health monitoring. A Kinetic Energy optimization technique and an Effective Independence Method are analyzed and numerical and theoretical issues are addressed for a cable-stayed bridge. Its application to a cable-stayed bridge is discussed to optimize the sensor placement for identification and control purposes.

• Proceedings of the KIEE Conference
• /
• 2005.07e
• /
• pp.31-33
• /
• 2005

The accelerating of industrial development causes electricity demand to increase. By that power equipments need high power, multi function and intelligence. Also consumers demand for guarantee power supplying of good quality and reasonable operating equipment. Also they require for reliance and stabilization of power facility. Therefore preventive maintenance of electric installation must be developed and improvement of domestic technical level is needed in the maintenance management of equipment. The diagnosis of trouble existence is technique that compares steady state with unusual condition, whereas the prediction technique makes a diagnosis of remaining equipments life. It is difficult for us to diagnose trouble existence of electric installation and to develop prediction method in building because of a wide scope for electric installation in building. And in this paper we will investigate diagnosis and prediction method for only switch part of electric installation in building.

• Journal of Aerospace System Engineering
• /
• v.11 no.5
• /
• pp.50-55
• /
• 2017

This research describes the ConOps(Concept of Operations) of sea-based guided weapon systems. The ConOps describes how the proposed system is to be used and is more descriptive than technical in terms of various stakeholders. It should be prepared to support the concept of the life cycle stage of the system. Developing ConOps plays an important role in ensuring that operational/maintenance, maintenance, and acquisition and development areas are better understood by users' needs and expectations. In this point of view, this work presents the process of deriving ConOps and aims to derive operational concept of maritime guided weapon system by using tools.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.4
• /
• pp.8-14
• /
• 2014

The purpose of this research was to develop evaluation conformity to operate courses based on CIPP evaluation model dedicated to approval of training organizations. In order to achieve the goal, the researchers scrutinized related documents and precedent studies, initiated the draft for evaluation conformity to operate courses and secured validity for evaluation conformity initiated through Delphi Method survey. To secure validity for evaluation conformity, the researchers conducted two Delphi Method surveys of an expert panel of 22 professionals from relevant fields including officials from the Ministry of Land, Infrastructure and Transport, researchers from Korea Transportation Safety Authority, instructors from approved training organizations and officials from industries. Through the surveys, the researchers determined 4 evaluation areas, 13 evaluation items and 52 evaluation indexes as the evaluation conformity to operate courses for aircraft maintenance mechanics. On top of that, the researchers established evaluation system in the courses for aviation professionals (aircraft maintenance mechanics), and suggested a follow-up studies regarding managing the quality of education.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.5
• /
• pp.63-71
• /
• 2010

This paper is about a research of steam curing which is one of the curing methods for accelerating the early-age strength of pre-cast concrete. With cylinder mold and mock-up specimen, the research was executed to study the best cycle of steam curing temperature through quantifying cycle of steam curing and maximum temperature, while the required strength is developed under the early-age. Moreover, causes and measurements for the high temperature of concrete, which is due to the steam curing, and the crack, which occurs when removing steel form, are stated. Ultimately, the economical method of producing, which satisfies early-age strength development and quality assurance while manufacturing PC structure, is stated.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.8
• /
• pp.2041-2049
• /
• 1998

This paper suggests a technique for program segmentation and maintenance using PSDG(Post-State Dependency Graph) that improves the quality of a software by identifying and detecting defects in already fixed source code. A program segmentation is performed by utilizing source code analysis which combines the measures of static, dynamic and semantic slicing when we need understandability of defect in programs for corrective maintanence. It provides users with a segmental principle to split a program by tracing state dependency of a source code with the graph, and clustering and highlighting, Through a modeling of the PSDG, elimination of ineffective program deadcode and generalization of related program segments arc possible, Additionally, it can be correlated with other design modeb as STD(State Transition Diagram), also be used as design documents.

• Korean Journal of Organic Agriculture
• /
• v.22 no.4
• /
• pp.841-854
• /
• 2014

This study aimed to analyze the selection criteria and priority settings for solid culture medium used in hydroponic crop production in farm households. Expert brain storming was carried out to extract solid culture medium selection criteria for hydroponic farming. As a result, 3 criteria of economy (cost), productivity, and environment, and 9 factors were extracted. A questionnaire survey of hydroponic farm households was conducted in Gyeonggi, Gangwon, and Chooncheong provinces. AHP analysis of the hydroponic solid culture medium selection criteria identified productivity as the most important criterion, chosen by 58.7% of the respondents, followed by economy (28.4%) and environment (12.9%). The 9 factors were rated by the respondents in the following decreasing order of importance: 1, crop yield (28.3%); 2, pest occurrence (18.5%); 3, maintenance/management costs (12.0%); 4, convenience of maintenance/management (13.4%); 5, initial investment cost (11.6%); 6, material energy consumption (6.5%); 7, waste recyclability (4.0%); 8, waste disposal costs (3.4%); and 9 environmental emissions (1.81%). These results imply that hydroponic farm households consider cultivation-related quality factors more important than economic factors, such as price of culture medium or installation cost.