• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.29 no.3
• /
• pp.187-196
• /
• 2009

The objectives of this study were to evaluate the different cutting dates on the changes of feed quality among five cereals (barley, wheat, rye, triticale and oat) for whole crop silage. Field trials were conducted at paddy field in Yesan, Chungnam Province and the aerial parts were clipped 10 days from 15 March to 15 June. Changes of acid detergent fiber (ADF) content in relation to different cutting dates was described by a quadratic curve for 5 winter cereals crops. ADF content reached a maximum at 5 days after heading in barley cultivar 'Youngyang', 7 days in wheat 'Keumkang', 18 days in rye 'Gogu', 1 days in triticale 'Shinyoung' and 10 days in oat 'Samhan'. Neutral detergent fiber (NDF) content were linearly increased as growing after overwintering and stagnated or slightly decreased after heading. The crude protein were linearly decreased throughout the growth period of 5 whole crop cereals. Digestible dry matter (DDM) content were decreased from early stages to heading and subsequently increased as grain filling. Relative feed value (RFV) for 5 crops were decreased as growing and subsequently increased as grain filling after heading. Barley cultivar for only forage use 'Youngyang' were lower at ADF and NDF content and higher at DDM and RFV after heading than those of other cereals for forage use. So, barley for whole crop silage was a good crop with high feed quality and high proportion of spikes compared with other winter cereal crops. Wheat cultivar for grain 'Keumkang' were higher at crude protein than those of other four cereals from overwintering to maturing and were higher at DDM and RFV after heading than those of rye, triticale and oat. Rye cultivar with cold tolerant and high fresh yielding 'Gogu' were highest at ADF and NDF content and lowest at DDM content and RFV. So, rye was a crop with low quality for forage use compared to other winter cereal crops. Triticale cultivar with flourishing and high yielding 'Shinyoung' was intermediated between barley and rye, and were linearly increased at DDM yield by different cutting dates. Oat cultivar with cold tolerant and high tillering 'Samhan' were lower at ADF and NDF content and higher at crude protein before heading, but after heading, there are not especially advantages compared to barley, wheat or triticale.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.6
• /
• pp.848-856
• /
• 2004

Black Bengal goat is primarily reared for meat, skin comes here as a by-product. The present trial describes the effect of age on different carcass characteristics of Black Bengal goats of either sex. A total of 61 Black Bengal goats of different age and sex groups were slaughtered. They were reared under semi-intensive management on milk alone or with concentrates (of 10.14 MJ ME and 10.48 g M/kg DM) and freshly cut Napier grass (2 MJ ME and 25 g CP/kg of fresh matter) that provides the estimated NRC (1981) requirement. The four age groups were: pre-weaned kids (0-90 day), post-weaned kids (91-180 days), growing (181-365 days) and adult (>365 days). Goats were slaughtered according to 'Halal' method by severing the major vessels of the throat by a transverse cut. Different slaughter parameters of Black Bengal goat can be best predicted from the equations as follows: live weight (kg)=0.801 (shoulder height (cm))-24.32, ($r^{2}$=0.94); carcass weight (kg)=0.364 (height at hind legs (cm))-11.54, ($r^{2}$=0.91); edible weight (kg)=0.623 (shoulder height (cm))-19.94, ($r^{2}$=0.91) and saleable weight (kg)=0.701 (shoulder height (cm))-21.99, ($r^{2}$=0.92). Live weight, carcass weight, edible weight and saleable weight of castrated goat at one-year onward ranges from 20-22, 9.4-10.5, 14-16 and 16.6-18.8 kg, respectively, which are about 80% higher than most of the reported observations on Black Bengal goat of same age and sex. Slaughter weight, warm carcass weight, edible weight and saleable weight increased curvilinearly with age of slaughter but not affected (p>0.05) by sex. However, linearity of the response curve of affect of age on mentioned parameters ends at around 9 months. Visceral fat as per cent of live weight increased curvilinearly with age and attain its maximum (about 6%) at about 500 days. However, linear part of the quadratic model ends at about 300 days when visceral fat content is about 4.8% of body weight. Blood and skin yield for one-year old male goat was 797 g and 1.61 kg, respectively. Absolute yield of blood and skin increased curvilinealry and attained maximum level at about 400 days (13.3 months). Average proportion of different carcass cut were - round 27%, rump 7%, loin 10%, ribs (6-12th) 14%, shoulder 21%, Neck 7%, chest 14%. Thigh and shoulder constituted about 48.3% of the cold carcass weight. Overall crude protein content of meat samples of different carcass cuts progressively decreased with age starting from 57 at 0-90 days to 58, 47 and 33 per cent, respectively at 91-180, 181-365 and >365 days, respectively. Overall meat fat content increased almost linearly from 11.1% during 91-180 days to 22.9 and 39.5% during 181-365 and >365days, respectively. Results from this trial suggest that both carcass yield and carcass composition changes with age; and sex have little or no effect on carcass yield and carcass composition. However, caution should be made in using second conclusion as there were few female animals slaughtered relative to the male. Optimum slaughter age for Black Bengal goat reared under semi-intensive management with adequate feeding and management would be about 9 months when their live weight, warm carcass weight, edible and saleable weight of carcass can be about 16.74, 7.28, 12.05 and 13.81 kg, respectively.

• Progress in Medical Physics
• /
• v.25 no.1
• /
• pp.31-36
• /
• 2014

We aimed to evaluate the dosimetric characteristics of reproducibility, linearity and dose dependence of optical stimulated luminance dosimeter (OSLD) in the Co-60 Gamma-rays and to analyze with a precedent study in field of the diagnostic radiography and radiotherapy. The reproducibility was 0.76% of the coefficient of variation, the homogeneity was within 1.5% of the coefficient of variation and OSLD had supra-linear response more than 3 Gy. So the correlation between dose and count was fitted by quadratic function. The count depletion by repeated reading was 0.04% per reading regardless of the irradiated dose. And the half time of decay curve according to the irradiated dose was 0.68 min. with 1 Gy, 1.04 min. with 5 Gy, and 1.10 min. with 10 Gy, respectively. In case of annealing for 30 min, the removal rate was 88% with 1 Gy, 90% with 5 Gy, and 92% with 10 Gy, respectively and 99% in case of annealing time for 4 hour. It is feasible to use OSLDs for dose evaluation in Co-60 Gamma-rays when considering the uncertainty on the procedure according to the irradiated dose.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.3
• /
• pp.165-180
• /
• 2015

Jurassic granite from Geochang was analysed with respect to the characteristics of the rock cleavage. The phases of distribution of microcracks were well evidenced from the enlarged photomicrographs(${\times}6.7$) of the thin section. In this study, the length - cumulative frequency diagrams were used for expressing the distribution characteristics of microcrack. The diagrams for the six directions were arranged in the magnitude of density(${\rho}$). These diagrams show an order of H2 < H1 < G2 < G1 < R2 < R1 from the related chart. Among six diagrams, the diagram for hardway 2(H2) occupies the lowermost region on the left. On the contrary, the diagram for rift 1(R1) occupies the uppermost region on the right. Curve patterns of the two diagrams change from uniform to exponential distribution type in accordance with the increased density. The overall distribution characteristics of the diagrams were well evidenced from the magnitude of the exponent(${\lambda}$) and length of line oa related to the exponential straight line. The magnitude of exponent governing the values of slope(${\theta}$) is inversely proportional to the values of microcrack parameters such as number(N), length(L) and density. On the contrary, length of line oa is directly proportional to the values of the above three parameters. Above microcrack parameters related to the order of arrangement of diagrams show an order of hardway(H1 + H2) < grain(G1 + G2) < rift(R1 + R2). The distribution characteristics of progressive variation are found among the six diagrams. The order of arrangement of the diagrams indicates a relative magnitude of the rock cleavage. Meanwhile, the parameters such as slope, exponent, density and length of line oa were arranged in an order of H2 < H1 < G2 < G1 < R2 < R1. The variation curves of a smooth quadratic function are shown from the related chart. From the correlation chart between density and the above parameters, a common regularity following power-law correlation function was derived. Finally, the analysis for the rock cleavage was conducted through the combination between the diagram and microcrack parameter. This type of combination contribute to the progressivity in evaluation for the rock cleavage.

• Korean Journal of Veterinary Research
• /
• v.41 no.2
• /
• pp.203-210
• /
• 2001

Here, we compared the effectiveness of 50 MeV($p{\to}RBe^+$) cyclotron fast neutrons versus $^{60}Co$ ${\gamma}$-rays by the apoptotic fragment frequency in both rat peripheral lymphocytes and crypt cells to check a radiobiological endpoint. The incidence of apoptotic cell death was increased in all irradiated groups, and radiation at all doses trigger rapid changes in both crypt cells and peripheral lymphocytes. These data suggest that apoptosis may play an important role in homeostasis of damaged radiosensitive target organ by removing damaged cells. The curve of dose-effect relationship for these data of apoptotic fragments frequencies was $y=0.3+(6.512{\pm}0.279)D(r^2=0.975)$ after neutrons, while $y=0.3+(4.435{\pm}0.473)D+(-1.300{\pm}0.551)D^2(r^2=0.988)$ after ${\gamma}$-rays. In addition, $y=3.5+(118.410{\pm}10.325)D+(-33.548{\pm}12.023)D^2(r^2=0.992)$ after ${\gamma}$-rays in rat lymphocytes. A significant dose-response relationship was found between the frequency of apoptotic cell and dose. These data show a trend towards increase of the numbers of apoptotic cells with increasing dose. Dose-response curves for high and low linear energy transfer (LET) radiation modalities in these studies were different. The relative biological effectiveness (RBE) value for crypt cells was 1.919. In addition, there were significant peaks on apoptosis induction at 4 and 6h after irradiation, and the morphological findings of the irradiated groups were typical apoptotic fragments in crypt cells that were hardly observed in the control group. Thus, apoptosis induction in both crypt cells and peripheral lymphocytes could be a useful endpoint of rat model for studying screening test and microdosimetic indicator to evaluate the biological effects of radiation-induced cell damage.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.45 no.2
• /
• pp.60-67
• /
• 2017

The purpose of this study was to evaluate the influence of landscaping shade materials' porosity on the Mean Radiant Temperature (MRT) of summer outdoors. The MRTs were measured under seven different types of black membranes with holes of 8mm diameter at different intervals applied on the top of wooden boxes, and compared with those of four additional control plots with or without shade and lateral boxes. The applied porosities were 0.5, 1, 2, 4, 8, 16%, and 32%, and three groups of three shades were compared sequentially from August 13 to September 8, 2016. The MRTs under the shade without lateral block, no shade with lateral block, and shade with lateral block were $33.08^{\circ}C$, $45.80^{\circ}C$, and $42.3^{\circ}C$, respectively, while that of no-shaded no-lateral screen was $44.26^{\circ}C$, based on records from 11:00 AM to 3:00 PM on the days with a peak globe temperature higher than $30^{\circ}C$. An ANCOVA analysis showed that the MRTs under the shades with 0.5, 1, 2, 4, 8, 16%, and 32% porosities were calculated as 43.40, 43.10, 41.49, 40.43, 39.61, $37.91^{\circ}C$, and $38.12^{\circ}C$, respectively, while that in the no shaded control box was $45.8^{\circ}C$. The curve fitted between MRTs and the porosity showed a U-shaped quadratic function with the minimum MRT at 16% practically or 22.5% statistically.