본 연구는 고온고습 시험을 통하여 Cell 레벨에서의 표면관찰 및 효율저하를 분석하였다. 고온고습 시험조건은 KS C IEC-61215에서 제시한 PV 모듈하의 조건을 이용하여 온도 $85^{\circ}C$, 습도 85%, 1000hr 동안 수행하였다. EL(Electroluminescence)촬영을 통하여 Cell 표면의 이상 유 무를 분석한 결과, 시간이 경과함에 따라, 부분적으로 표면이 손상되어 변색되는 것을 확인하였다. 고온고습 시험 전 단결정 Cell 및 다결정 Cell의 효율은 각각 17.7%, 15.5%였으며, 1000hr 수행 후 15.6%, 14.0%로 각각 11.9%와 9.3%의 감소율을 보였다. 또한, 경년 시 나타나는 전기적 특성을 분석하기 위하여 FF(Fill Factor)값을 분석한 결과, 고온고습 시험 후 단결정 Cell은 78.7%에서 75.0%로 4.7%, 다결정 Cell은 78.1%에서 76.7%로 1.8%의 감소율을 보였다. 태양전지 실리콘의 원자배열 및 순도에 따라 효율 변화에 영향을 받아 단결정 Cell이 다결정 Cell보다 효율저하가 크게 나타났다고 판단된다. 또한, FF감소율보다 효율 감소율이 크게 저하된 것을 확인할 수 있었으며, 이는 Cell의 외부환경적 요인에 의한 표면 손상이 p-n접합층 접촉저항과 경년 시 나타나는 FF 감소율보다 크게 영향을 준 것으로 판단된다.
최근 발전하는 초박막 자기 시료의 정확한 자기 모멘트 측정을 위하여 저자기 모멘트 표준 시료를 제작하였다. 정밀한 저자기 모멘트 표준시료를 제작하기 위해서 자력계를 미리 자기잡음으로부터 차폐시켰고, 시료준비과정에서 강자성 불순물을 고려한 시료의 순도, 절단 방법, 시료의 모양과 두께 등을 고려하였다. 본 연구에서는 SQUID 자력계를 이용한 자기 모멘트 측정에 적합하게 $4mm{\times}6mm$ 면적을 갖는 Al, Ti과 W로 된 판상형 시료 3 개를 준비하였다. Pd 금속의 경우는 이미 잘 보정된 실린더형 시료를 사용하였다. 준비된 세 개의 판상형 시료의 경우 50,000 Oe 이내의 자기장영역에서 자기이력현상이 관측되지 않았고 모두 양호한 선형성을 보였다. 290K에서 310K까지의 온도영역에서 Ti, Al, W의 자기모멘트 값의 변화는 각각 0.7%, 1.5%, 0.1% 이내로 작았다. 본 연구에서 준비된 각각의 시편에 대해 자기모멘트 값을 결정하였으며, round robin test를 통하여 측정값의 신뢰도를 확인하였다. 그 결과 본 연구에서 제작한 표준시료는 저자기 모멘트 측정에 편리하고 적합하게 활용될 수 있음을 알 수 있었다.
This study was implemented as a part of the experiment to develop two kinds of soil-based Benzo[a]pyrene (BaP) proficiency testing materials (PTMs) for soil analysis. A test was carried out for the check of solubility of the reference material (high purity reagent) using several solvents. Another test was also conducted for the evaluation of homogeneity and stability of two kinds of candidate soil reference materials. The test analysis of BaP in terms of the candidate materials was conducted according to the Standard Soil Analytical Methods by Ministry of Environment. Dissolution of the reference material was shown to vary depending on solvent type and was higher in the order of Dichloromethane > Acetone > Acetone/MeOH (9 : 1) > N-hexane. In addition, the slope on calibration curve for BaP standard solutions was largest on BaP standard solutions prepared with dichloromethane of the tested solvents. Such tendency appeared egually in the commercial BaP standard solution. Therefore, it is thought to be reasonable to use dichloromethane as the solvent in case of the standard stock solution that is used for the measurement of BaP concentration in soil. ISO 13528 and IUPAC protocol were used for verification of homogeneity on the two kinds of soil candidate materials, Both candidate materials were sufficiently homogeneous. Stability assessment of the two candidate materials was made according to ISO Guide 35 and the result showed that both batches did not have any long-term and short term stability issues that might occur during shipping. However, monitoring results of BaP concentration in soil showed that BaP concentration of the two batches measured at 15 days after the sample preparation was reduced by about 24~37% compared with that of the samples measured on 0 day of the sample preparation. Identification was done with several treatments such as irradiation and sterilization etc. The major cause was shown to be irradiation to the samples.
Akay, Canan;Tanis, Merve Cakirbay;Mumcu, Emre;Kilicarslan, Mehmet Ali;Sen, Murat
The Journal of Advanced Prosthodontics
/
제10권1호
/
pp.43-49
/
2018
PURPOSE. The purpose of this in vitro study is to examine the effects of a nano-structured alumina coating on the adhesion between resin cements and zirconia ceramics using a four-point bending test. MATERIALS AND METHODS. 100 pairs of zirconium bar specimens were prepared with dimensions of $25mm{\times}2mm{\times}5mm$ and cementation surfaces of $5mm{\times}2mm$. The samples were divided into 5 groups of 20 pairs each. The groups are as follows: Group I (C) - Control with no surface modification, Group II (APA) - airborne-particle-abrasion with $110{\mu}m$ high-purity aluminum oxide ($Al_2O_3$) particles, Group III (ROC) - airborne-particle-abrasion with $110{\mu}m$ silica modified aluminum oxide ($Al_2O_3+SiO_2$) particles, Group IV (TCS) - tribochemical silica coated with $Al_2O_3$ particles, and Group V (AlC) - nano alumina coating. The surface modifications were assessed on two samples selected from each group by atomic force microscopy and scanning electron microscopy. The samples were cemented with two different self-adhesive resin cements. The bending bond strength was evaluated by mechanical testing. RESULTS. According to the ANOVA results, surface treatments, different cement types, and their interactions were statistically significant (P<.05). The highest flexural bond strengths were obtained in nano-structured alumina coated zirconia surfaces (50.4 MPa) and the lowest values were obtained in the control group (12.00 MPa), both of which were cemented using a self-adhesive resin cement. CONCLUSION. The surface modifications tested in the current study affected the surface roughness and flexural bond strength of zirconia. The nano alumina coating method significantly increased the flexural bond strength of zirconia ceramics.
Park, GiRim;Jang, Hyun A;Jo, Sung-Hwan;Park, Younghoon;Oh, Sang-Keun;Nam, Moon
농업과학연구
/
제45권3호
/
pp.385-400
/
2018
Marker-assisted backcrossing (MABC) is useful for selecting offspring with a highly recovered genetic background for a recurrent parent at early generation unlike rice and other field crops. Molecular marker sets applicable to practical MABC are scarce in vegetable crops including tomatoes. In this study, we used the National Center for Biotechnology Information- short read archive (NCBI-SRA) database that provided the whole genome sequences of 234 tomato accessions and selected 27,680 tag-single nucleotide polymorphisms (tag-SNPs) that can identify haplotypes in the tomato genome. From this SNP dataset, a total of 143 tag-SNPs that have a high polymorphism information content (PIC) value (> 0.3) and are physically evenly distributed on each chromosome were selected as a MABC marker set. This marker set was tested for its polymorphism in each pairwise cross combination constructed with 124 of the 234 tomato accessions, and a relatively high number of SNP markers polymorphic for the cross combination was observed. The reliability of the MABC SNP set was assessed by converting 18 SNPs into Luna probe-based high-resolution melting (HRM) markers and genotyping nine tomato accessions. The results show that the SNP information and HRM marker genotype matched in 98.6% of the experiment data points, indicating that our sequence analysis pipeline for SNP mining worked successfully. The tag-SNP set for the MABC developed in this study can be useful for not only a practical backcrossing program but also for cultivar identification and F1 seed purity test in tomatoes.
선별된 Aspergillus 속의 한 균주인 S-1의 조(粗) naringin 분해효소의 정제에 관하여 검토한 결과 정제도의 관점에서 Sephadex G-200, starch gel electrophoresis, DEAE-Cellulose column chromatogram, 황산암모늄분획의 순위로 좋았으며 각 정제법에 따른 결과는 다음과 같다. 1) 조효소(粗酵素)를 starch gel electrophoresis 한 결과 단백 mg 당 naringinase 활성이 1,000 unit 로 정제되었다. 2. 단백 mg 당 0.37 unit, naringinase 활성인 조효소(粗酵素)를 황산암모늄분획한 결과 0.25포화 이하에서는 protein per mg 3 unit, 0.75포화 이하에서는 12 unit, 075포화 이상 완전포화 fraction 에서는 34 unit 로 정제되었으며 회수율로 볼때는 황산암모늄 0.75포화 이하에서 가장 좋았다. 3. Sephadex G-200에 의해 정제한 결과 protein per mg 1,337 unit 였으며 DEAE-Cellulose column chromatography 한 결과는 430 unit per protein mg 으로 정제되었다. 4. DEAE-Cellulose column chromatography 후 sephadex G-200에 의해 정제한 결과는 여지전기영동에 의해 단일 단백으로 나타났으며 이 단일 단백은 naringin 을 purunin 까지만 분해하였다.
Since late of 2000, KIER has developed a novel pyrolysis process for production of fuel oils from polymer wastes. It could have been possible due to large-scale funding of the Resource Recycling R&D Center. The target was to develop an uncatalyzed, continuous and automatic process producing oils that can be used as a fuel for small-scale industrial boilers. The process development has proceeded in three stages bench-scale unit, pilot plant and demonstration plant. As a result, the demonstration plant having capacity of 3,000 tons/year has been constructed and is currently under test operation for optimization of operation conditions. The process consisted of four parts ; feeding system, cracking reactor, refining system and others. Raw materials were pretreated via shredding and classifying to remove minerals, water, etc. There were 3 kind of products, oils(80%), gas(15%), carbonic residue(5%). The main products i.e. oils were gasoline and diesel. The calorific value of gas has been found to be about 18,000kcal/$m^3$ which is similar to petroleum gas and shows that it could be used as a process fuel. Key technologies adopted in the process are 1) Recirculation of feed for rapid melting and enhancement of fluidity for automatic control of system, 2) Tubular reactor specially-designed for heavy heat flux and prevention of coking, 3)Recirculation of heavy fraction for prevention of wax formation, and 4) continuous removal & re-reaction of sludge for high yield of main product (oil) and minimization of residue. The advantages of the process are full automation, continuous operation, no requirement of catalyst, minimization of coking and sludge problems, maximizing the product(fuel oil) yield and purity, low initial investment and operation costs and environment- friendly process. In this presentation, background of pyrolysis technology development, the details of KIER pyrolysis process flow, key technologies and the performances of the process will be discussed in detail.
핵심 microsatellite 마커를 활용하여 우리나라에서 품종보호출원 및 등록된 콩 148 품종에 대한 DNA 프로파일 데이터베이스를 구축한 다음 유전적 유사도 분석을 통한 품종 식별력 정도를 조사하였다. 콩 148품종을 120개의 microsatellite 마커로 검정하고 밴드의 패턴이 명확하고 다형성 정도가 높은 핵심 마커 16개의 대립유전자의 수는 6 ~ 28개로 나타났고 평균 대립유전자의 수는 12.75개였다. PIC 값은 0.753 ~ 0.951 사이에 분포하였고 평균값은 0.863으로 아주 높았다. 콩 148 품종에 대하여 Jaccard 방법에 따라 유전적 유사도를 설정한 다음 비가중 산술평균결합에 의해 집괴분석하여 계통도를 작성하였을 때, 콩의 품종 유형 및 품종 육성 계보에 따라 5개의 대그룹으로 나누어졌으며 모든 품종이 식별이 가능하였다. 본 연구에서 콩 품종식별용 핵심 microsatellite는 품종보호출원 품종의 구별성, 균일성, 안정성의 확인, 품종진 위성과 관련된 종자분쟁, 종자 순도 관리에 매우 유용하게 활용될 수 있을 것이다.
태양광산업의 value chain중 up-stream쪽인 고순도 실리콘산업은 셀, 모듈, 시스템 쪽에 비하여 영업 이익률이나 부가가치 측면에서 매우 높은 성장성을 현재 보여주고 있으며 최근 원자력산업의 안전성 문제가 대두됨으로 인하여 태양광수요가 전 세계적으로 증대되는 경향을 나타내어 태양광용 실리콘의 수요가 확대됨과 아울러 spot시장에서의 가격 또한 상승하고 있다. 이런 관점에서 잉곳 및 웨이퍼 가공 중에 발생하는 고순도 실리콘 폐기물의 재활용 이 다시 주목받고 있다. 태양전지 웨이퍼(wafer)용 소재는 6N급 이상의 결정질 실리콘 잉곳(ingot)이 주를 이루며, 고효율의 셀을 제조하기 위해서 단결정 실리콘 잉곳이 많이 사용된다. 실리콘 단결정을 육성하는 방법에는 Floating zone 법, Czochralski 법, Bridgeman 법, CVD 등 매우 다양하다. 이 중 Czochralski 법은 전체 생산량의 대부분을 차지하고 있는 방법으로, 용융액에서 결정을 인상하여 ingot을 제작하는 방법이다. 그러나 대량의 전기에너지를 소비하여 제작되는 고순도의 실리콘 단결정 잉곳은 후 가공공정에서 그 절반 이상이 분말(powder) 및 슬러지(sludge)로 폐기되므로, 자원의 재활용 및 환경오염 측면에서 주요과제가 되고 있다. Czochralski 법으로 제작된 ingot의 경우 그 표면이 매끄럽지 못하여, 웨이퍼 단위의 가공 시 형태가 진원이 될 수 있도록 표면을 미리 연마(grinding)하는데, 이때에도 미세 분말이 다량 발생하게 된다. 본 연구에서는 이러한 고순도 단결정 실리콘 ingot의 연마 가공공정에서 발생한 미세 분말을 용해하여 보았다. 진공 챔버(chamber) 내부에 유도가열 코일과 냉도가니로 구성된 장비를 통해 전자기유도가열을 이용하여 실리콘 분말 폐기물을 용해하고, 그 시편을 ICP-MS 및 비저항 측정을 통해 분말 의 특성을 조사하여 재활용 가능성을 검토해 보았다.
HgCdTe Is the most versatile material for the developing infrared devices. Not like III-V compound semiconductors or silicon-based photo-detecting materials, HgCdTe has unique characteristics such as adjustable bandgap, very high electron mobility, and large difference between electron and hole mobilities. Many research groups have been interested in this material since early 70's, but mainly due to its thermodynamic difficulties for preparing materials, no single growth technique is appreciated as a standard growth technique in this research field. Solid state recrystallization(SSR), travelling heater method(THM), and Bridgman growth are major techniques used to grow bulk HgCdTe material. Materials with high quality and purity can be grown using these bulk growth techniques, however, due to the large separation between solidus and liquidus line on the phase diagram, it is very difficult to grow large materials with minimun defects. Various epitaxial growth techniques were adopted to get large area HgCdTe and among them liquid phase epitaxy(LPE), metal organic chemical vapor deposition(MOCVD), and molecular beam epitaxy(MBE) are most frequently used techniques. There are also various types of photo-detectors utilizing HgCdTe materials, and photovoltaic and photoconductive devices are most interested types of detectors up to these days. For the larger may detectors, photovoltaic devices have some advantages over power-requiring photoconductive devices. In this paper we reported the main results on the HgCdTe growing and characterization including LPE and MOCVD, device fabrication and its characteristics such as single element and linear array($8{\times}1$ PC, $128{\times}1$ PV and 4120{\times}1$ PC). Also we included the results of the dewar manufacturing, assembling, and optical and environmental test of the detectors.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.