• KIEAE Journal
• /
• 제14권6호
• /
• pp.5-13
• /
• 2014

Various studies on lighting energy savings are conducted, given that lighting energy consumption accounts 23.5% of building energy consumption. Especially, external type light shelf's efficiency is acknowledged; however, its application is limited in Korea, where high rise building ratio is high, due to high wind pressure. This study delves into natural lighting system to cope with wind pressure, and proposes the punching plate-installed light shelf. This study actually draws lighting energy output, according to whether the punching plate is applied through the test-bed, and verifies the effectiveness of the punching plate-installed light shelf. The conclusion is presented below: First) The result of performance evaluation of light shelf with the punching plate in winter solstice showed that the awning area decreased as the opening ratio increased so that the indoor distributed illumination tended to increase, and $-40^{\circ}$ which was advantageous for awning was determined as the proper angle. Second) The light shelf with the punching plate in spring/autumn equinox shows improved lighting according to the angle, and the appropriate angle of light shelf with the punching plate has increased to $15^{\circ}$ and $20^{\circ}$ according to the opening ratio in comparison to $5^{\circ}C$ which is the appropriate angle of light shelf with no punching plate due to the reflection area reduced by the reflecting plate with holes. Third) The result of performance evaluation of light shelf with the punching plate in summer solstice showed that the lighting performance tended to decrease as the opening ratio increased. 4) The light shelf with the punching plate incurs a 50% energy loss in comparison to the light shelf with no punching plate. However, its effectiveness has been proven in the aspects that it can bring a 50% energy saving in comparison to the case with no installation of light shelf and that it can be designed in response to wind pressure on the high floors.

• 한국해양공학회지
• /
• 제35권2호
• /
• pp.113-120
• /
• 2021

In order to perform a precise wave tank experiment, it is necessary to maintain the incident wave generated by the wavemaker in a steady state and to effectively remove the reflected waves. In this paper, a combined sloping-wall-type punching plate wave absorber was proposed to attenuate reflected waves effectively in a two-dimensional mini wave tank. Using the four-point reflection separation method, the reflected waves were measured to determine the reflection coefficients. Experiments were conducted under various punching plate porosities, sloping plate angles, and incident wave conditions to evaluate the performance of the combined punching plate wave absorber. The most effective wave absorbing performance was achieved when the porosity was 10% and the inclination angle of the punching plate was 18.6° under the present condition. It was also found that the installation of the sloping plate could improve the wave attenuation performance by generating the shoaling effect of the incident wave.

• Computers and Concrete
• /
• 제20권6호
• /
• pp.731-738
• /
• 2017

Reinforced concrete flat plates consist of slabs supported directly on columns. The absence of beams makes these systems attractive due to advantages such as economical formwork, shorter construction time, less total building height with more clear space and architectural flexibility. Punching shear failure is usually the governing failure mode of flat plate structures. Punching failure is brittle in nature which induces more vulnerability to this type of structure. To analyze the flat plate behavior under punching shear, twelve finite element models of flat plate on a column with different parameters have been developed and verified with experimental results. The maximum range of variation of punching stress, obtained numerically, is within 10% of the experimental results. Additional finite element models have been developed to analyze the influence of integrity reinforcement, clear cover and column reinforcement. Variation of clear cover influences the punching capacity of flat plate. Proposed finite element model can be a substitute to mechanical model to understand the influence of clear cover. Variation of slab thickness along with column reinforcement has noteworthy impact on punching capacity. From the study it has been noted that integrity reinforcement can increase the punching capacity as much as 19 percent in terms of force and 101 percent in terms of deformation.

• 한국해양공학회지
• /
• 제18권1호
• /
• pp.1-6
• /
• 2004

In this paper, the performance of a wave absorbing system using an inclined punching plate, was investigated. Using the multi-domain boundary element method (BEM), the reflection coefficients of an inclined punching plate were tested with various design parameters, such as inclined angle, porosity, and wave frequencies. To confirm the numerical solutions, the systematic model test was conducted at 2-D tank and square tank. The numerical results were in good agreement with the experimental results within the entire frequency range. It was found that an inclined punching plate had an excellent wave absorbing efficiency, compared to a horizontal one. Also, the optimal range of an inclined angle had an excellent wave absorbing efficiency, compared to a horizontal one the optimal range of the inclined angle is 10°<β<20°. The developed wave absorber was installed at KRISO's square basin, and is working effectively for various model tests.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.37-40
• /
• 2008

The study is an experimental test on full-scale flat plate slab-column interior connection. The punching shear on the flat plate slab-column connection can bring about the reason of the brittle punching shear failure which may result of collapsing the whole structure. From the development of residential flat plate system, the shear reinforcement is developed for preventing the punching shear. For making sure of the punching shear capacity, developed for shear reinforcement in slab-column connection, the structural test is performed. The dimension of the slabs was 2620*2725*180mm with square column (600*800mm). The slabs were tested up to failure monotonic vertical shear forces. The presences of S/S bar and wire mesh substantially increased the punching shear capacity and the ductility of the slab-column connections.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.48-51
• /
• 2004

This paper is to study the response of flat plate slab-column connections consisting of various types of shear reinforcement and steel plate subjected to gravity loadings, mainly punching shear forces using the non-destructive testing, spectral analysis of surface waves and structural experiments. The base specimen failed due to punching shear generated from the gravity. The three other types of slab shear reinforcement and steel plate showed effective in resisting punching shear for these types of connections under gravity loading. This study has focused in evaluating the velocity response of a Surface wave during the early age as the poured concrete specimens have been hardened, the possibility of damage detection in the slab-column connection and the relationship between the punching shear forces and the surface wave velocities under the condition that the punching shear forces had gradually increased until the flat plate slab in slab-column connection had been failed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.260-265
• /
• 2002

In micro hole punching process, it is very difficult to align punch with die hole. Misalignment can cause a falling-on in hole quality and breakage of punch and die. Micro punching using soft die plate without a die hole has a big advantage because it is not necessary to align punch with die hole and to consider die clearance. Soft die plates are made by polymers or hard rubbers which are softer than metals. In this study, several micro punching experiments are conducted. Micro punching test with some materials shows that micro hole punching is feasible with some soft die plates. Through the section shape obtained by mounting and polishing, the punched hole quality is measured and the shapes of burr and dome we studied.

• 한국해양환경ㆍ에너지학회지
• /
• 제2권1호
• /
• pp.40-48
• /
• 1999

해양공학과 관련된 모형실험을 위하여 많이 사용되고 있는 조파수조(2차원수조, 장수조, 사각수조)에 소파장치는 필수적인 장치이다. 본 논문에서는 새로운 개념의 소파장치의 소파성능을 실험을 통하여 살펴보았다. 새로 고안된 소파장치는 소파성능이 우수하고 가볍기 때문에 설치가 용이하다. 또한 넓은 설치공간이 필요치 않아 수조공간 활용에 있어 효과적이며 조파기로부터 발생된 파장에 큰 영향을 받지 않기 때문에 아주 큰 장파만 피한다면 거의 완벽하게 파를 소멸시킬 수 있는 장점을 가지고 있다. 본 소파장치는 일정한 크기의 구멍이 균일하게 배열된 타공판을 입사파의 진행방향과 수평으로 수면밑에 잠기게 설치한 형태로 파가 수평형 타공판을 통과하면서 타공판의 구멍을 통하여 강한 제트 흐름이 형성되면서 파 에너지가 소멸되는 특징을 가지고 있다. 모형실험 결과 수평형 타공판의 소파성능은 타공판의 잠긴 깊이와 판의 전체면적과 뚫린 부분의 면적의 비로 표현되는 공극율에 밀접한 관련이 있으며, 각각의 값은 최대 소파성능을 발휘하는 최적의 값을 가지고 있음을 규명하였다. 수평형 타공판의 앞쪽을 뒤쪽보다 약간 기울게 설치하는 방법도 특정한 주파수 범위내에서는 수평형에 비하여 우수한 소파성능을 보이며, 이때 타공판의 경사각도도 소파장치 성능을 결정하는데 중요한 변수임을 밝혔다.

• 한국해안해양공학회지
• /
• 제14권4호
• /
• pp.265-273
• /
• 2002

본 논문에서는 수면 밑에 잠긴 수평형 타공판의 소파특성을 이론계산과 모형실험을 통하여 살펴보았다. 타공판은 일정한 크기의 구멍이 균일하게 배열된 형태로, 파가 타공판 위를 통과하면서 타공판의 구멍을 통하여 강한 제트 흐름이 형성되면서 파 에너지가 소멸되는 특징을 가지고 있다. 이론해석 방법으로 선형파 이론에 근거한 고유함수전개법을 사용하였다. 타공판을 통과하는 유체의 법선방향속도는 타공판 전후의 압력차에 선형적으로 비례한다는 Darcy의 법칙을 가정하였다. 이때 공극율 계수라 불리는 비례상수는 타공판의 공극율과 밀접한 관계가 있다. 공극율 계수와 공극율사이의 함수 관계식을 얻기 위하여 수직벽 앞에 놓여진 6개의 서로 다른 공극율을 가진 타공판에 대하여 규칙파중에서 반사율을계측하였다. 해석결과와 모형실험결과를 비교하여 공극율 계수와 타공판의 공극율사이에는선형관계(b=57.63P-0.9717)가 있음을 밝혔다. 또한 최대 소파성능을 발휘하는 타공판의 공극율은 0.1근방이며, 잠긴깊이의 범위는 $d/h\\leq0.2$임을 확인하였다.

• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.63-70
• /
• 2010

We developed a new punching system that generates pinholes expressing texts or images on a plastic plate. The pin-holed plate is used as a new glamorous display board reflecting colorful lights from the light emitting diode (LED) installed on the edge side of the plate. The four degree-of-freedom punching system was designed to make same multiple holes on four plastic plates simultaneously. For this motion, we designed a structure for a simultaneous motion of the system. For even reflection of the lights from texts or images on the board and fast production of the pin-holed boards, fast motion including precise position control is very important. We also built a PC-based integrated control system including a GUI program to help users easily design luminous texts or images on the plastic plate. Also, we conducted a performance test of the system to verify the punching speed and position control of the pin holes on the plate.