• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.59-68
• /
• 1996

This study was aimed to characterize the laser cutting process for the cold rolled stainless steel sheet. The principal process parameters of the cutting process were applied to both the continuous wave form and the pulsed wave form for the laser output mode. The laser-oxygen cutting process and the laser-nitrogen cutting process were also considered to characterize the quality and efficiency of the cutting process. The laser-oxygen cutting process revealed the better productivity than the laser-nitrogen cutting process, since the laser energy and the exothermic oxidation energy exerted on the laser-oxygen cutting process simultaneously during the entire cutting process. However, the straightness of the cutting section, which was considered as the most important factors, was inferior to that of the laser-nitrogen cutting process due to the formation of chromum oxide on the cutting surface. Frequency and duration of the pulsed wave form act as the main factors for the better quality, When the frequency increased from 100 Hz to 200 Hz and the duty increased from 20% to 40%, the quality factors such as the height of dross and the surface roughness were improved remarkably. The increase in the frequency from 200 Hz to 300 Hz, on the other hand, revealed the less effective in the cutting quality.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.8
• /
• pp.1270-1278
• /
• 2004

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG laser welding. A large porosity was formed in a keyhole mode of deeply penetrated weld metal of any stainless steel. Solidification cracks were present in STS 310S with above 0.017%P and undercuts were formed in STS 303 with about 0.3%S. The conditions for the formation of porosity were determined in further detail in STS 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of STS 310S through a high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• The Korean Journal of Pain
• /
• v.20 no.2
• /
• pp.195-198
• /
• 2007

A cluster headache is characterized by the occurrence of strictly unilateral and periocular pain with no side shift and ipsilateral oculofacial autonomic symptoms such as conjunctival injection, lacrimation, rhinorrhea and miosis. Cluster headache involves the activation of parasympathetic nerve structures located within the sphenopalatine ganglion, and blockade of the sphenopalatine ganglion has been shown to be effective at the treatment of cluster headaches that are resistant to conventional therapy. Herein, we describe a case of a 50-year-old male with a cluster headache that could not be controlled by conventional treatments who showed improvement after being treated with sphenopalatine ganglion pulsed radiofrequency.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1422-1432
• /
• 2017

This paper presents a buck-boost converter-based bipolar pulse generator, which is able to generate bipolar exponential pulses across a resistive load. The concept of the proposed approach depends on operating the involved buck-boost converters in discontinuous current conduction mode with high-voltage gain and enhanced efficiency. A full design of the pulse generator and its passive components is presented to ensure generating the pulses with the desired specifications (rise time, pulse width, and pulse magnitude) for a given load resistance and input dc voltage. In case of moderate pulsed output voltages (i.e. few of kV), one module of the presented bipolar generator can be employed. While in case of high-voltage pulsed output, multi-module version can be employed, where each module is fed from an isolated dc source and their outputs are connected in series. Simulation models for the proposed approach are built to elucidate their performance in case of one-module as well as multi-module based generator. Finally, a scaled-down prototype for one-module of buck-boost converter-based bipolar pulse generator is implemented to validate the proposed concept.

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.327-332
• /
• 2020

Laser induced surface activation (LISA) technology requires refined selection of process variables to fabricate conductive microcircuits on a general polymer material. Among the process variables, laser mode is one of the crucial factors to make a reliable conductor pattern. Here we compare the continuous wave (CW) laser mode with the pulse wave (PW) laser mode through determination of the surface roughness and circuit accuracy. In the CW laser mode, the surface roughness is pronounced during the implementation of the conductive circuit, which results in uneven plating. In the PW laser mode, the surface is relatively smooth and uniform, and the formed conductive circuit layer has few defects with excellent adhesion to the polymer material. As a result of a change of laser mode from CW to PW, the value of Ra of the polymer material decreases from 0.6 ㎛ to 0.2 ㎛; the value of Ra after the plating process decreases from 0.8 ㎛ to 0.4 ㎛, and a tight bonding force between the polymer source material and the conductive copper plating layer is achieved. In conclusion, this study shows that the PW laser process yields an excellent conductive circuit on a polymeric material.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.283-292
• /
• 2009

Laser-based ultrasonic sensing requires the probe with fixed fecal length, but this requirement is not essential in laser-based ultrasonic generation. Based on this fact, we designed a pulsed laser-based ultrasonic wave propagation imaging (UWPI) system with a tilting mirror system for rapid scanning of target, and an in-line band-pass filtering capable of ultrasoaic mode selection. 1D-temporal averaging, 2D-spatial averaging, and 3D-data structure building algorithms were developed far clearer results allowing fur higher damage detectability. The imaging results on a flat stainless steel plate were presented in movie and snapshot formats which showed the propagation of ultrasound visible as a concentric wavefield emerging from the location of an ultrasonic sensor. A hole in the plate with a diameter of 1 mm was indicated by the scattering wavefields. The results showed that this robust UWPI system is independent of focal length and reference data requirements.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.1
• /
• pp.15-19
• /
• 2004

In this paper, we present the fabrication and characteristic analysis of Sagnac interferometric optical fiber senior(OFS) system for detecting pulsed ultrasonic signal in underwater. The hollow cylindrical mandrel wound round by single mode optical fiber is used as sensing component. The ultrasonic signal source is simulated by the PZT actuator operated by an function generator. The distance dependency of the OFS's sensitivity was measured. The sensitivity has been shown to be inversely propotional to the square-root of distance between ultrasonic source and sensing component. It has also been shown that the OFS could detect the signals less affected by ultrasonic path comparing to conventional acousto-electric sensor. and accurate location of ultrasonic signal could be carried out using two OFSs.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.5
• /
• pp.553-556
• /
• 1992

The ${CO}_2$ laser absorption measurement of ${CH}_3{CH}_2Br$ utilizing photoacoustic (PA) technique was performed using a cw and a pulsed ${CO}_2$ lasers. The absorption profile in the ${CO}_2$ laser wavelength region (9-10 ${\mu}$m) and the macroscopic small signal absorption cross section at 10P(20) (10.59 ${\mu}$m, 944 $cm^{-1}$) laser line were measured using a cw ${CO}_2$ laser. The laser fluence dependence on infrared multiphoton absorption (IRMPA) was also studied with a pulsed TEA ${CO}_2$ laser at 10P(20) laser line. In view of monotonic increase of PA signal with the rise of laser fluence, it was suggested that the anharmonicity in pumped vibration mode did not restrict ir multiphoton absorption in ${CH}_3{CH}_2Br$ system as found in large molecular system.

• Nuclear Engineering and Technology
• /
• v.55 no.5
• /
• pp.1665-1670
• /
• 2023

It is shown that in the IBR-2M reactor by the end of the reactor cycle, changes in dynamics are observed associated with a strong weakening of the fast power feedback (PF), as a result of which the reactor becomes oscillatorily unstable. After each week of zero-power operation the negative changes in reactor dynamics disappear and the stability of the reactor is restored. Thus, the reactor undergoes cyclic changes in the oscillatory instability. The correlation between of a fast PF and a slow PF is experimentally observed, which makes it possible to almost completely eliminate the cyclic component of instability by changing the control mode of rods of the control system.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.215-218
• /
• 2004

The pseudolites are ground-based transmitters that can be configured to emit GPS-like signals with the purpose of enhancing the GPS by providing increased accuracy, integrity, and availability. Although the use of the pseudolites offers many potentially significant benefits, a number of technical issues must also be addressed. One is the pseudolite signal power level which is related with near-far problem, and other issues include deployment requirements, signal data rate, signal integrity monitoring, and user antenna location and sensitivity. In order to solve the near-far problem, the frequency offset or the pulsing schemes is implemented in most the pseudolites. However, in the case of the previous pulsing scheme with the fixed code pattern, the near-far problem still remains. This paper aims to design a sequential pulsing scheme to avoid the near-far problem. A pulse mode pseudolite has less interference than the continuous mode.