• 자동차안전학회지
• /
• 제9권3호
• /
• pp.7-12
• /
• 2017

The whiplash is the most important issue of low speed rear-impact. So auto makers are committed to developing a seat to improve whiplash injury. Most NCAP tests have been used by same pulse (Mid Velocity 16kph). Only Euro NCAP uses different pulse that consists of Low, Mid, High velocity. But Euro NCAP also uses same pulse in Mid velocity as other NCAP test. That Mid velocity NCAP pulse was made by rear impact that has 90's vehicle structure properties. That pulse was used until now days. However these days, auto maker use more high tensile steel than 90's as customer and society demand more fuel efficiency and light vehicle with good safety structure. So modern vehicles have different pulse patterns of rear impact than NCAP pulse and 90's vehicle crash properties. In this paper, the test was conducted by following condition. Target car was impacted by the rigid barrier with certain velocity. Finally target vehicle gained delta V 16kph which was same velocity as NCAP Mid Velocity pulse. It is critical velocity which occur long period neck injury. It is very different pulse that was gained by real car impact from NCAP pulse. And it has higher peak G with high fluctuation and short duration than NCAP pulse.

• 동의생리병리학회지
• /
• 제25권3호
• /
• pp.551-557
• /
• 2011

The purpose of this study is to investigate the relation between brachial-ankle pulse wave velocity and the features of metabolic syndrome, and differences according to sex in patients diagnosed cerebral infarction. The study group comprised 61 patients over age 30 who were diagnosed cerebral infarction, accompanied with metabolic syndrome. The brachial-ankle pulse wave velocity, blood pressure, lipid profiles, fasting blood glucose, body mass index were measured. Also we checked past history of patients. Then we analyzed the association between brachial-ankle pulse wave velocity and the features of metabolic syndrome. Pearson correlation analysis reflected the variables affecting the brachial-ankle pulse wave velocity as follows : Age, SBP(systolic blood pressure), DBP(diastolic blood pressure), FBS(fasting blood glucose) were positively correlated. As a result of regression analysis, in patients with cerebral infarction accompanied with metabolic syndrome, the brachial-ankle pulse wave velocity is affected by age to men, SBP, FBS, DBP to women. The brachial-ankle pulse wave velocity is not affected by the components of metabolic syndrome, except blood pressure, FBS, in patients with ischemic stroke.

• Journal of Magnetics
• /
• 제20권1호
• /
• pp.47-51
• /
• 2015

We measured radial arterial pulse signals using a prototype of a clip-type pulsimeter equipped with a permanent magnet and a Hall device, which produced signals through a voltage-detecting circuit. The systolic peak time and the reflective peak time for a temporally pulsed signal were analyzed for an arbitrary pulse wave at one position of a small permanent magnet. The measured value of the peripheral pulse wave velocity was about 1.25-1.52 m/s, demonstrating the accuracy of this new method. To measure the peripheral blood flow velocity, we simultaneously connected the radial artery pulsimeter to a photoplethysmography meter. The average value of the peripheral blood flow velocity was about 0.27-0.50 m/s.

• 한국환경과학회지
• /
• 제23권12호
• /
• pp.2045-2056
• /
• 2014

In this study, pressure drop was measured in the pulse jet bag filter without venturi on which 16 numbers of filter bags (Ø$140{\times}850{\ell}$) are installed according to operation condition(filtration velocity, inlet dust concentration, pulse pressure, and pulse interval) using coke dust from steel mill. The obtained 180 pressure drop test data were used to predict pressure drop with multiple regression model so that pressure drop data can be used for effective operation condition and as basic data for economical design. The prediction results showed that when filtration velocity was increased by 1%, pressure drop was increased by 2.2% which indicated that filtration velocity among operation condition was attributed on the pressure drop the most. Pressure was dropped by 1.53% when pulse pressure was increased by 1% which also confirmed that pulse pressure was the major factor affecting on the pressure drop next to filtration velocity. Meanwhile, pressure drops were found increased by 0.3% and 0.37%, respectively when inlet dust concentration and pulse interval were increased by 1% implying that the effects of inlet dust concentration and pulse interval were less as compared with those changes of filtration velocity and pulse pressure. Therefore, the larger effect on the pressure drop the pulse jet bag filter was found in the order of filtration velocity($V_f$), pulse pressure($P_p$), inlet dust concentration($C_i$), pulse interval($P_i$). Also, the prediction result of filtration velocity, inlet dust concentration, pulse pressure, and pulse interval which showed the largest effect on the pressure drop indicated that stable operation can be executed with filtration velocity less than 1.5 m/min and inlet dust concentration less than $4g/m^3$. However, it was regarded that pulse pressure and pulse interval need to be adjusted when inlet dust concentration is higher than $4g/m^3$. When filtration velocity and pulse pressure were examined, operation was possible regardless of changes in pulse pressure if filtration velocity was at 1.5 m/min. If filtration velocity was increased to 2 m/min. operation would be possible only when pulse pressure was set at higher than $5.8kgf/cm^2$. Also, the prediction result of pressure drop with filtration velocity and pulse interval showed that operation with pulse interval less than 50 sec. should be carried out under filtration velocity at 1.5 m/min. While, pulse interval should be set at lower than 11 sec. if filtration velocity was set at 2 m/min. Under the conditions of filtration velocity lower than 1 m/min and high pulse pressure higher than $7kgf/cm^2$, though pressure drop would be less, in this case, economic feasibility would be low due to increased in installation and operation cost since scale of dust collection equipment becomes larger and life of filtration bag becomes shortened due to high pulse pressure.

• Computers and Concrete
• /
• 제6권6호
• /
• pp.437-450
• /
• 2009

The effect of six different curing conditions on compressive strength and ultrasonic pulse velocity (UPV) of volcanic pumice concrete (VPC) and normal concrete (NC) has been studied. The curing conditions include water, air, low temperature ($4^{\circ}C$) and different elevated temperatures of up to $110^{\circ}C$. The curing age varies from 3 days to 91 days. The development in the pulse velocity and the compressive strength is found to be higher in full water curing than the other curing conditions. The reduction of pulse velocity and compressive strength is more in high temperature curing conditions and also more in VPC compared to NC. Curing conditions affect the relationship between pulse velocity and compressive strength of both VPC and NC.

• 한국농공학회지
• /
• 제43권4호
• /
• pp.97-105
• /
• 2001

The ultrasonic pulse velocity test has a strong potential to be developed into a very useful and relatively inexpensive in-place test for assuring the quality of concrete placed in structure. The main problem in realizing this potential is that the relationship between compressive strength ad ultrasonic pulse velocity is uncertain and concrete is an inherently variable material. The objective of this study is to improve the reliability of in-place concrete strength predictions by ultrasonic pulse velocity method. Experimental cement content, s/a rate, and curing condition of concrete. Accuracy of the prediction expressed in empirical formula are examined by multiple regression analysis and linear regression analysis and practical equation for estimation the concrete strength are proposed. Multiple regression model uses water-cement ratio cement content s/a rate, and pulse velocity as dependent variables and the compressive strength as an independent variable. Also linear regression model is used to only pulse velocity as dependent variables. Comparing the results of the analysis the proposed equation expressed highest reliability than other previous proposed equations.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.210-211
• /
• 2018

In this study, the ultrasonic pulse velocity of the concrete cooled to room temperature after heating and the concrete during heating were evaluated. Also, the ultrasonic pulse velocity and mechanical properties of concrete were compared. As a result, the ultrasonic pulse velocity decreased when the concrete degraded during heating, and the ultrasonic pulse velocity of the cooled concrete decreased significantly. Which is consistent with the deterioration of mechanical properties of concrete.

• 한국산림과학회지
• /
• 제85권2호
• /
• pp.288-299
• /
• 1996

본 연구는 heat pulse법을 이용하여 신갈나무 장령림 임분(林分)의 증산량(蒸散量)을 알기 위한 기초연구로서, 신갈나무 입목에 있어서 일사량(日射量), 온도(溫度), 습도(濕度)(대기포차(大氣飽差)) 등의 변화(變化)에 따른 heat pulse 속도(速度)의 일변화와 계절변화, 방위별 heat pulse 속도(速度)의 차이, 변재부에 있어 깊이별 heat pulse 속도(速度)의 차이, 우세목(優勢木), 준우세목(準優勢木), 열세목(劣勢木)의 heat pulse 속도(速度)의 차이, 엽(葉)의 수분포텐셜과 heat pulse 속도(速度)와의 관계, 줄기에 있어 수분상승의 방향, 그리고, heat pulse법으로 측정한 단목(單木)과 임분(林分)의 일일(一日), 월별(月別), 년간(年間) 증산량(蒸散量) 등을 측정고찰하였다. 얻어진 결과를 요약하면 다음과 같다. 1. 신갈나무의 heat pulse 속도(速度)(V)와 수액유속(樹液流速)(SFR)과의 관계는 SFR=1.37V였다. 2. 우세목(優勢木), 준우세목(準優勢木), 열세목(劣勢木)의 heat pulse 속도(速度)를 비교하면, 수액유속(樹液流速)은 우세목(優勢木)이 가장 높고, 준우세목(準優勢木), 열세목(劣勢木) 순위였다. Heat pulse 속도(速度)는 일사량(日射量), 온도(溫度), 대기포차(大氣飽差) 등의 크기에 따라 일변화하였다. 3. Heat pulse 속도(速度)와 엽(葉)의 수분포텐셜은 거의 비슷한 일변화를 나타냈다. 4. Heat pulse 속도(速度)의 계절변화는 7월에 평균 2.9cm/hr로 가장 낮았고, 5월이 평균 4.0cm/hr로 가장 높게 나타났다. 5. 줄기에 있어서 heat pulse 속도(速度)의 차이는 북측이 가장 높았고, 서측이 그 다음 순이었으며, 남측과 동측은 큰 차이없이 가장 낮은 값을 나타냈다. 6. 변재부에 있어서 깊이별 heat pulse 속도(速度)의 차이는 수피로부터 0.5cm 깊이에서 가장 높고, 다음 1.0cm, 1.5cm 순으로 나타났다. 7. 줄기에 있어 수분이동방향(水分移動方向)은 4본 모두 부분적(部分的) 수직상승(垂直上昇)(sectorial straight ascent)을 나타내고 있었다. 8. 수액유량(樹液流量)(SF)은 SF=1.37AV식으로 나타났고, 이 식으로 구한 수액유량(樹液流量)은 우세목(優勢木)이 준우세목(準優勢木)과 열세목(劣勢木)보다 현저히 높았다. 9. 1ha의 임분(林分)에 대한 1일의 증산량(蒸散量)의 구성비율(構成比率)은 낮이 72%, 밤이 28%였고, 증산량(蒸散量)은 약 5.6ton/ha/day이었다. 10. 1ha의 월별(月別) 증산량(蒸散量)은 5월이 168ton/ha/month으로 가장 많았고, 7월이 125ton/ha/month로 가장 낮았다. 또 1 ha의 년간(年間) 증산량(蒸散量)은 839ton/ha/yr이었다.

• 한국자기학회지
• /
• 제22권4호
• /
• pp.136-141
• /
• 2012

본 연구에서는 집게형 맥진기와 심전도계를 이용하여 전기적인 심전도 파형과 요골동맥파형을 동시 측정하여 얻은 맥파전달속도를 분석하였다. 두 신호의 동시 측정에 의한 맥파전달속도는 평균 6 m/s의 값을 보여 주었으며, ECG 파형과 홀소자 맥진파형으로 동시 측정한 방법은 기존 방법들 보다 정확하게 맥파전달속도를 측정할 수 있는 새로운 방법임을 입증하였다. 따라서 이결과는 한방의료기기인 맥진기에서 측정된 데이터를 임상적으로 활용할 수 있음을 보인다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제5권3호
• /
• pp.123-130
• /
• 2001

The purpose of this study is to suggest the non-destructive equation for the estimation of concrete strength by ultrasonic pulse velocity at the Age of 28day compressive strength of $600{\sim}1000kg/cm^2$. For this purpose, selected test variables were water-hinder ratio, replacement ratio of silica fume, binder content, maximum size of coarse aggregate and sand-aggregate ratio. From the results, the average increase or decrease of ultrasonic pulse velocity is 61m/sec for each 1% of moisture content. And the correlation equation between the ultrasonic pulse velocity and the compressive strength of concrete is as follows. $F_c=896.3V_p-3514$ ($R^2$ = 0.81) where, $F_c$ : compressive strength($kgf/cm^2$), $V_p$ : ultrasonic velocity(km/sec).