• ETRI Journal
• /
• 제39권5호
• /
• pp.746-755
• /
• 2017

In this paper, an electrostatic discharge (ESD) protection circuit is designed for use as a 12 V power clamp by using a parasitic-diode-triggered silicon controlled rectifier. The breakdown voltage and trigger voltage ($V_t$) of the proposed ESD protection circuit are improved by varying the length between the n-well and the p-well, and by adding $n^+/p^+$ floating regions. Moreover, the holding voltage ($V_h$) is improved by using segmented technology. The proposed circuit was fabricated using a $0.18-{\mu}m$ bipolar-CMOS-DMOS process with a width of $100{\mu}m$. The electrical characteristics and robustness of the proposed ESD circuit were analyzed using transmission line pulse measurements and an ESD pulse generator. The electrical characteristics of the proposed circuit were also analyzed at high temperature (300 K to 500 K) to verify thermal performance. After optimization, the $V_t$ of the proposed circuit increased from 14 V to 27.8 V, and $V_h$ increased from 5.3 V to 13.6 V. The proposed circuit exhibited good robustness characteristics, enduring human-body-model surges at 7.4 kV and machine-model surges at 450 V.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.327-328
• /
• 2017

This paper presents the power supply system which is made of three units: the capacitor charging and main pulse unit, simmer power supply unit, and series trigger unit. The capacitor charging and main pulse unit charges the capacitor bank by using the series parallel resonant converter and the generated main pulses apply to the lamp. The series trigger unit ionize the xenon gas located in the lamp and the simmer power supply unit sustains the ionized condition. It means that the lamp lifetime and efficiency are advanced by reducing the number of triggering. Not only the operation of the proposed system but also the performance of each unit will be verified by the experimental results.

• Journal of electromagnetic engineering and science
• /
• 제18권1호
• /
• pp.20-28
• /
• 2018

The time synchronization of each sub-unit of a pulsed generator is important to generate an output high-power radio frequency (RF) signal. To obtain the time synchronization between an input RF signal fed by an external source and an electron beam produced by an electric pulse generator, the influence of different charging voltages on a delay and a rise time of the output pulse waveform in the electric pulse generator should be carefully considered. This paper aims to study the timing characteristics of the delay and the rise time as a function of different charging voltages with a peak value of less than -35 kV in the high-voltage pulse generator, including a trigger generator (TG) and a pulse-forming line (PFL). The simulation has been carried out to estimate characteristics in the time domain, in addition to their output high-voltage amplitude. Experimental results compared with those obtained by simulation indicate that the delay of the output pulses of the TG and PFL, which are made by controlling the external triggering signal with respect to different charging voltages, is getting longer as the charging voltage is increasing, and their rise times are inversely proportional to the amplitude of the charging voltage.

• Journal of Korean Vacuum Science & Technology
• /
• 제7권2호
• /
• pp.45-56
• /
• 2003

A high flux metal plasma pulse ion source, which can simultaneously perform ion implantation and deposition, was developed and tested to evaluate its performance using the prototype. Flux of ion source was measured to be 5 A and bi-polar pulse power supply with a peak voltage of 250 V, repetition of 20 Hz and width of 100 ${\mu}\textrm{s}$ has an output current of 2 kA and average power of 2 kW. Trigger power supply is a high voltage pulse generator producing a peak voltage of 12 kV, peak current of 50 A and repetition rate of 20 Hz. The acceleration column for providing target energy up to ion implantation is carefully designed and compatible with UHV (ultra high vacuum) application. Prototype systems including various ion sources are fabricated for the performance test in the vacuum and evaluated to be more competitive than the existing equipments through repeated deposition experiments.

• 한국항행학회논문지
• /
• 제11권2호
• /
• pp.163-169
• /
• 2007

본 논문에서는 x-ray 영상시스템의 영상을 획득하기 위하여 x-ray 발생기와 영상획득시스템 사이의 동기를 맞추어 주는 트리거 발생기를 연구분석 하였다. 무선 트리거 발생기는 디지털영상 획득시스템으로부터 영상획득의 시작을 지시할 수 있는 ACQ_START 신호와 영상획득의 끝을 알리는 ACC_END 신호를 발생시킬 수 있도록 설계하였다. 디지털 영상의 획득은 ACQ_START 신호와 ACQ_END 신호 사이의 시간동안에만 정확하게 이루어지며 무선 원격 x-ray 신호의 검출을 통하여 유선통신 프로토콜 없이 정확한 x-ray 영상의 획득이 가능하고 20 mAs 의 x-ray 레벨에서 3.5 line pair /mm 분해능을 나타냄을 확인하였다.

• 전자공학회논문지A
• /
• 제32A권4호
• /
• pp.47-56
• /
• 1995

In this paper the model of the MQE-IMD-based neural trigger circuit is improved, where MQW-IMD is a new semiconductor device proposed and experimentally demonstrated by the author for the hardware implementation of the neural networks. The electron energy of AlXGa1-XAsbarrier is calculated by Ensemble Monte Carlo simulation according to the variation of Al mole fraction x and the applied electric field, whtich had been roughly estimated in the previous paper because of the difficulty to get the data. And in the consideration of the tunneling of the confined electrons within the quantum well the accuracy of the impact ionization rate is enhaned. Finally, the dependance of the frequency of pulse-train on the number of quantum wells can be calculated by modelling the effect of the distance of the induced positive charge from the cathode on the electric field at the cathode.

• 한국인터넷방송통신학회논문지
• /
• 제20권2호
• /
• pp.133-140
• /
• 2020

본 논문에서는 고해상도 거리분해능을 가지는 펄스 레이더에서의 고정밀 거리 인지 및 생성 방법에 대해서 다룬다. 레이더의 목표한 거리분해성능을 테스트를 위해서 점검장비를 이용하는데 이때 설계한 거리분해능 이하의 거리를 정확히 인지하고 발생시켜야 한다. 이때 발생하는 거리 정확도는 일반적으로 시스템 기준 클럭(clock) 주파수에 비례한다. 하지만 종래의 방법은 기준 클럭 타이밍을 트리거(trigger)하고 발생시는 프로세스의 입력 기준 클럭이 한계가 있고 설령 이러한 칩이 있다할지라도 매우 고가이다. 이를 해결하기 위해 일반적인 프로세서에서 범용적으로 적용 가능한 위상 변위 합성을 이용한 거리 신호 생성 방법과 구조를 제시하였다. 제안하는 방법을 이용하여 모의 실험을 진행하였으며 종래에 방법에서 발생하는 문제점을 완전 제거하는 결과를 확인하였다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권12호
• /
• pp.511-517
• /
• 2006

The key issues in high power, high energy applications such as electromagnetic launchers include safety, reliability, flexibility, efficiency, compactness, and cost. To explore some of the issues, a control scheme for a large current wave-forming was designed, built and experimentally verified using a 2.4MJ pulse power system (PPS). The PPS was made up of eight capacitors bank unit, each containing six capacitors connected in parallel. Therefore there were 48 capacitors in total, with ratings of 22kV and 50kJ each. Each unit is charged through a charging switch that is operated by air pressure. For discharging each unit has a triggered vacuum switch (TVS) with ratings of 200kA and 250kV. Hence, flexibility of a large current wave-forming can be obtained by controlling the charging voltage and the discharging times. The whole control system includes a personal computer(PC), RS232 and RS485 pseudo converter, electric/optical signal converters and eight 80C196KC micro-controller based capacitor-bank module(CBM) controllers. Hence, the PC based controller can set the capacitor charging voltages and the TVS trigger timings of each CBM controller for the current wave-forming. It also monitors and records the system status data. We illustrated that our control scheme was able to generate the large current pulse flexibly and safely by experiments. The our control scheme minimize the use of optical cables without reducing EMI noise immunity and reliability, this is resulting in cost reduction. Also, the reliability was increased by isolating ground doubly, it reduced drastically the interference of the large voltage pulse induced by the large current pulse. This paper contains the complete control scheme and details of each subsystem unit.

• Journal of information and communication convergence engineering
• /
• 제6권4호
• /
• pp.411-416
• /
• 2008

When compose magnetic field curer by belt and band style and need by magnetic field ripple last month, produce self-discipline roof. Bred in muscle disease (lumbago, backbone disease, corpulence) back. Result that study, manufactured various variableness band style - magnetic field probe firstly. Can establish self-discipline treatment pulse price by disease secondly. Could seek correct variableness band punishment, - magnetic field probe relationship implementation and property in waist, and so on, shoulder, neck, arm, leg, ankle, wrist etc. by third. Could find variableness band style energy value that need in-magnetic field Probe's treatment by fourth. This research could design pulse of self-discipline in band form and apply each according to disease.

• 전기의세계
• /
• 제26권3호
• /
• pp.76-83
• /
• 1977

The choice of control method and circuit must be decided after a broad inspection with the characteristics of load and control elements as well as that of electric and mechanical nature. In the present study, Pulse width modulated(PWM) SCR chopper was chosen and for the electric commutation, Jones' forced method was taken bacause of its having enough reverse bias energy. Objectives of experimentation by this system are; 1) the condition of SCR as a gate trigger pulse. 2) the observation of phenomena at the time of forced commutation 3) the experimentation on characteristics of speed control by PWM chopper. Above experimentation shows good characteristics, however, in the limit of narrow gap between the ON and OFF pulses, a complete control was not possible. So, that must be the point to be studied further alone with the harmonics influence.