• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권11호
• /
• pp.566-571
• /
• 2004

Pulse modulation technique provide additional controling method for electron temperature and density in rf and microwave processing plasma. Transient characteristics of electron density and temperature have been measured in pulse modulated rf inductively coupled argon plasma using simple probe circuit. Electron temperature relaxation is clearly identified in the after glow stage. Controllability of average electron temperature and density depends on the modulation frequency and duty ratio. Numerical calculation of time-dependent electron density and temperature have been performed based on the global model. It has been shown that simple langmuir probe measurement method used for continuous plasma is also applicable to time-dependent measurement of pulse modulated plasma.

• 한국전기전자재료학회논문지
• /
• 제18권11호
• /
• pp.1061-1067
• /
• 2005

The resonant frequency modulation of $YBa_2Cu_3O_{7-x}$ meander lines has been investigated as functions of optical pulse energy and temperature by using a network analyzer. The frequency-domain measurements are performed by controlling both the resonant frequency and the frequency width. The meander lines, configured in a microstrip geometry, are illuminated by optical pulses from an actively mode-locked Nd:YAG laser. The variation of the resonant frequency shows a quadratic dependence on the reduced optical pulse energy $P/P_c$, where $P_c$ is defined as the critical optical pulse energy at which resonance signal has disappeared. As for the dependence on temperature, the results are in good agreement with the previously reported data.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.307-312
• /
• 1994

In this investigation the PFM(Pulse Frequency Modulation} will be used for optimizing PWM inverter pulse pattern. In traditional the pulse frequency of PWM is kept const. But modulated PWM's frequency in this study, the sinusoidal inverter's performance should be improved. The PWM pulsepatterns are definitely controlled so that the time-integral function of the voltage vectors in the space vector notation may show a circular locus. Further, performance index will be minimized because of minimizing distortion of output current. Finally, we will implement itusingsingle-chip microprocessor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1617-1618
• /
• 2013

• 한국군사과학기술학회지
• /
• 제24권4호
• /
• pp.368-373
• /
• 2021

This paper presents a method of independent pulse repetition frequency(PRF) generation and control for frequency phase calibration on mono-pulse radar at a remote location. In order to generate an independent PRF signal of 320[Hz], pulse width modulation(PWM) of 16-bit timer/counter was applied. For a precision control of PRF signal, 16-bit timer/counter interrupt was changed for each period. Therefore, average frequency of PRF could be controlled by 0.0001[Hz]. To calibrate a frequency phase of mono-pulse radar at a remote location, the proposed PRF generator with a precision control of frequency was used regardless of receiving PRF signal from a radar. For the verification of the proposed PRF generator, theoretical analysis and experimental results are included.

• 전력전자학회논문지
• /
• 제14권1호
• /
• pp.54-61
• /
• 2009

본 논문에서는 강압형 DC-DC 컨버터의 성능 개선을 위한 스위칭 기법인 2차 SDSDM (Space Dithered Sigma Delta Modulation)방식을 제안한다. PWM (Pulse Width Modulation) 방식은 일정 스위칭 주파수 대역에서의 고조파로 인해 소음, 전자파 장애, 스위칭 손실 등을 유발한다. 이러한 문제를 해결하기 위한 DSDM 방식의 일종인 1차 SDSDM은 랜덤 디더(Random Dither) 발생기가 1차 SDM의 양자화기(quatizer) 입력단에 위치하여 스위칭 주파수가 분산된다. 강압형 DC/DC 컨버터에 제안하는 2차 SDSDM의 방식을 적용한 실험 결과를 통해 타당성을 검증한다.

• 제어로봇시스템학회논문지
• /
• 제21권1호
• /
• pp.76-79
• /
• 2015

Visible light communication (VLC) is a short range optical communication technology using light emitting diodes. In this paper, we implement variable pulse position modulation (VPPM) defined in the IEEE 802.15.7 standard with a Cortex-M processor, which is a new modulation scheme for VLC providing a dimming control mechanism for flicker-free optical communication. The synchronization procedure between the transmitter and receiver is not defined clearly in the VPPM standard. In order to synchronize the transmitter and receiver easily, two overhead bits are used including one start bit and one stop bit modulated by on-off keying (OOK). Experimental results under various environmental conditions show that the proposed VPPM can support a seamless 100 Kbps data rate with 10 levels in the dimming control.

• 한국조명전기설비학회지:조명전기설비
• /
• 제2권2호
• /
• pp.59-63
• /
• 1988

고정 AC 전력전원에서 PWN(Pulse Width Modulation) 기법은 전압과 기본파 주파수를 가변 시키는 데 이용되어 왔다. 종래의 PWN 기법은 전류수, 필터크기 등의 문제점 때문에 PWN 출력 전압파형을 모터 구동 등의 제어 대상에 응용하는 연구가 진행되었다. 그러나 본 논문에서는 출력단 고속 스윗칭 소자를 사용하여 캐리어 주파수를 10(KHz)-45(KHz)까지 정현 PWN 시키고, 인버터의 출력단 파형은 소용량LPF(Low Pass Filter)를 사용하여 PAM(Pulse Amplitude Modulation)을 얻어냈다. 정현 PWN 제어 회로는 속응성과 제어성을 고려하여 마이크로 프로세서와 아날로그 회로로 혼합구성 하였다. 그리고 실험 결과는 변조도 0.6-1.0까지 변할 때 전압 파형을 관찰했다.

• Journal of Power Electronics
• /
• 제14권3호
• /
• pp.519-530
• /
• 2014

A novel simplified pulse width modulation(PWM) strategy for neutral point clamped (NPC) three-level converter is proposed in this paper.The direct output voltage modulation is applied to reduce the calculation time. Based on this strategy, several optimized control methods are proposed. The neutral point potential balancing algorithm is discussed and a fine neutral point potential balancing scheme is introduced. Moreover, the minimum pulse width compensation and switching losses reduction can be easily achieved using this modulation strategy. This strategy also gains good results even with the unequal DC link capacitor. The modulation principle is studied in detail and the validity of this simplified PWM strategy is experimentally verified in this paper. The experiment results indicated that the proposed PWM strategy has excellent performance, and the neutral point potential can be balanced well with unequal DC link captaincies.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.