• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.44-53
• /
• 2014

This research were aimed at developing starches which have high preservability and high bonding strength from corn starch, modified cationic and oxidized corn starches, as compared to the fermented wheat starch. On the lining that attaching the base paper on the back of the work with paste, the coating weight was determined by the solid contents of the paste rather than the viscosity of paste. Adhesive strength and stiffness were also determined by the solid contents of the paste. Corn starch had lower solid contents, higher viscosity, and higher adhesive strength than other starches. In the iodine stain to the surface of peeled base paper off, paste deeply penetrated into the traditional Hanji than modern Hanji. And oxidized starch paste deeply penetrated into the paper layer than the cationic starch.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.1
• /
• pp.59-66
• /
• 2013

Fillers have been used for printing paper to improve printability, sheet formation and optical properties and to reduce production costs by replacing expensive wood pulps. However, an increased filler content will decrease paper strength because filler particles interfere with fiber-fiber bonding. In order to increase filler content without sacrificing too much paper strength in high filler content papers, the surface of precipitated calcium carbonate (PCC) has been modified by adsorbing anionic polyacrylamide and cationic starch in series. The adsorbed polymer layers would enhance interactions between the filler surface and the fiber surface, improving internal bonding. It was found that the modified PCC increased paper strength at a given filler content compared to the coventional method. Negligible differences in optical properties and formation of paper, filler and fines retention and drainage on the wire section were observed between the modified and the conventional PCC. However, the decreased bulk of paper was observed when the modified PCC was used.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.1
• /
• pp.29-43
• /
• 1998

This study was to investigate the effect of .compressive load and cyclic humidity(2$0^{\circ}C$, 65% and 90% RH) on the physical and mechanical properties of corrugated board. Corrugated boards in the study were under compressive load and under cyclic humidity, and their properties were compared to those without load. Results were summarized as follows ; 1 Statistically significant correlation was shown between the ring crush of the boards and the compressive strength of cylinder specimen made from the boards. So we could study the compressive behavior of board with cylinder specimen. 2. The boards under the compressive load increased their moisture content and thickness much more than those without load both in constant and in cyclic RH. 3. The compressive and tensile strength of board samples were inversely and closely proportional to the sheet moisture content regardless of their load and humidity history. 4. The moisture content did not show any significant proportionality to the change of burst strength of boards within this experiment. 5. Board reconditioning in standard condition led to the recovery of the strength loss that had occurred under various load and humidity condition. 6. The handsheets prepared from the boards that had experienced compressive load and cyclic humidity, and those with no-load and 65% RH did not show any significant difference in strength properties. No physical damage or load-carrying properties of the wood fiber were observed by the compressive load and cyclic humidity history.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.4
• /
• pp.69-75
• /
• 1999

This study was performed to investigated the application of mixed resins for corrugated container board. The corrugated container board yields a sandwich structure in which a linerboard material is glued to a corrugated medium . Now, manufacturing corrugated container boards don't provide sufficient strength, and result in box failure during shipping . Therefore improvement of box strength is necessary . In this study, we intend to improve box strength by improving corrugated medium strength with mixed resins and to find the optimum treatment condition of this resins. First, we tried to mixed resins as Starch+CMC, Starch_Irea, CMC+Urea, Second, investigated to applicability of this resins for corrugated medium , and the third, measured tensile index, burst index, and edgewise compression index on liner, medium paper, and single faced corrugated container board. In this test results, we obtained that the improvement ratios of tensile index in liner and medium paper were approximately 80-185%, 60-118% , respectively. The respecting improvement ratios of edgewise compression index of single faced corrugated container board was approximately 91-124%, relatively. In addition, we concluded that optimum condition in mixing ratio was 1 :3 with CMC + Urea and the ap[plication amounts was 9% on materials. Fro manufacture of corrugated container board, optimum condition in mixing ratio was 1 : 3 with 5% CMC +Urea , because of considering to improvement of strength on cost.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.2
• /
• pp.29-34
• /
• 2012

For the purpose of developing liner board for water-resistant corrugated board in the cold chain system, several types of base paper for corrugated board were purchased from the market and 6 different boards were produced in the paperboard mill by applying the chemicals on the base paper. Then, water-moisture resistant performance and physical properties of the boards were compared each other. The liner board which is dried at high temperature with pressure by Condebelt papermaking system(CK paper) showed a superior performance in strength over common liner boards. Strength of the board increased by surface chemical treatment up to 60% of compressive strength and 30% of bursting strength. Starch insolubilization with Ammonium-Zirconium Carbonate(AZC) and surface coating with a surface size and a moisture resistant chemical on CK paper showed the best result. Therefore, this method was recommended to produce the outer liner board for water -resistant corrugated board.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.63-71
• /
• 2012

This study was carried out to investigate pulping properties of the forest biomass arising from the national forest management operation. The forest biomass was collected and classified into many groups according to their species and age. After the chips were made from the forest biomass, the measurement of chip size and chemical analysis were performed. To make the pulps from the forest biomass, the kraft pulping was applied and thereafter the physical and optical properties of kraft pulps were measured. The pulp fibers from the forest biomass had the similar mean fiber length, but their properties became different according to wood species and ages. Differently from the other species, kraft pulps from chestnut wood had the highest kappa number. Acacia, paulownia and chestnut woods made kraft pulps with lower tensile strength and brightness than the others. It could be concluded that acacia, paulownia and chestnut woods must be screened out in order to make a good quality of kraft pulps while being collected during Forest Management Operation.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.21-27
• /
• 2014

As a part of the study on manufacture of low density paper by organic bulky agent treatment, the effects of cationic fatty acid bulky agent on physical and optical properties of handsheets were elucidated. The research on change of physical and optical properties of paper samples according to bulky agent concentration, pulp type, and pulp combination were carried out. The results demonstrated that an increase of the concentration of cationic fatty acid bulky agent was proportional to an increase of the bulky properties of paper samples while tensile strength decreased. Also, the more the treated concentration of cationic fatty acid bulky agent increased, the more the ISO brightness of paper samples decreased while the opacity increased. The effectiveness of bulky agent with softwood bleached kraft pulp (SwBKP) was higher than that with hardwood bleached kraft pulp (HwBKP). In addition, the effectiveness with mixed pulps was higher than that with single pulp.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.76-84
• /
• 2019

This study evaluated the microleakage of three restorative materials and three tricalcium silicate-based pulp capping agents. The restorative materials were composite resin (CR), resin-reinforced glass ionomer cement (RMGI), and traditional glass ionomer cement (GIC) and the pulp capping agents were TheraCal $LC^{(R)}$ (TLC), $Biodentine^{(R)}$ (BD), and $ProRoot^{(R)}$ white MTA (WMTA). Additionally, shear bond strengths between the pulp-capping agents and dentine were compared. Class V cavities were made in bovine incisors and classified into nine groups according to the type of pulp-capping agent and final restoration. After immersion in 0.5% fuchsin solution, each specimen was observed with a stereoscopic microscope to score microleakage level. The crowns of the bovine incisors were implanted into acrylic resin, cut horizontally, and divided into three groups. TLC, BD and WMTA blocks were applied on dentine, and the shear bond strengths were measured using a universal testing machine. The microleakage was lowest in TLC + GIC, TLC + RMGI, TLC + CR, and BD + GIC groups and highest in WMTA + RMGI and WMTA + CR groups. The shear bond strength of BD group was the highest and that of WMTA group was significantly lower than the others.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.1
• /
• pp.79-87
• /
• 1999

To use the agricultural residues as the raw material of molded packaging material, the packaging trays were manufactured from rice-straw pulp. The physical properties were measured to compare non-treated trays with the addition trays, such as the addition of starch, rosin size, carboxymethyl cellulose(CMC), polyethylene glycol(PEG), alkylketene dimer(AKD), polyacryl amide(PAM). The results were as follows : 1. In the addition of starch, air permeability at addition of 5% was highest. Bursting strength and tensile strength were smaller than non-treated trays. 2. In the addition of rosin size, air permeability, bursting strength and tensile strength were smaller than non-treated trays. 3. In the addition of CMC, air permeability was higher than non-treated trays. Bursting strength and tensile strength were similar to non-treated trays. 4. In the addition of PEG, air permeability was higher than non-treated trays. Bursting strength at addition of 3% was the highest and tensile strength was smaller than non-treated trays. 5. In the addition of AKD, air permeability at addition of 1% and 5% was higher than non-treated trays. Bursting strength and tensile strength were smaller than non-treated trays. 6. In the addition of PAM, air permeability at addition of 0.01% was the highest. Tensile strength at addition of 0.01% were higher than non-treated trays. 7. The water absorption of the trays decreased with increasing adding of natural additives.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.70-70
• /
• 2000

This study is a continuation of the previous experimental analysis and is mostly focused on handsheet strength properties. Four completely different fibers, which were Hw-BKP, Sw-BKP, white ledger, and OCC, were selected to investigate the effect of mechanical pre-treatment by Hobart mixer on handsheet strength properties. After equal time mechanical pre-treatment, the fibers were refined with laboratory valley beater for 10, 20 and 30 minutes, and handsheets were prepared from the fibers for physical strength comparison. Handsheets from SW-BKP and OCC showed 5-30% increase of breaking length, burst index, tear index, and compression index while handsheets from HW-BKP and white ledger no Increase except tear index. In Hobart mixer pre-treatment, HW-BKP and white ledger fibers were easily attached to the wall of the mixer bowl and mechanical action was not effectively applied. The fiber length of Hw-BKP and white ledger were 0.837mm and 1.591 mm, respectively, while SW-BKP and OCC were 2.744 mn and 2.033 mm, respectively, in weight weighted length. The effective mechanical pre-treatment seems to be related to the fiber length. Tear indexes of the pre-treated furnish were much higher than no pre-treatment at the same breaking length level.