• Korean Journal of Food Science and Technology
• /
• v.24 no.4
• /
• pp.353-360
• /
• 1992

This study was carried out to investigate the changes of quality in yogurt during delivery and storage. To do this, microbiological, physico-chemical and sensory properties in stirred yogurt were studied at different temperatures $(10^{\circ}C$ & $20^{\circ}C)$ and shakings (100 rpm & 200 rpm for 30 min). Titratable acidity and TCA soluble nitrogen in yogurt were increased in accordance with increase of temperature and time, while pH, lactose and lactic acid bacteria tended to be decreased. Interestingly enough, shaking conditions almost did not influence these studies. In sensory evaluation it showed that acidity was strong and sweetness was weak as increasing the storage temperature and time, but there were no significant differences until 10 days at $10^{\circ}C$ and 3 days at $20^{\circ}C$. Off-flavor was developed after 12 days at $10^{\circ}C$ with only 200 rpm shaking and after 6 days at $20^{\circ}C$ in both shaking conditions. These yogurts were not suitable for consumer. Viscosity in the yogurt became high as the temperature and time were increased. Viscosity was lower in yogurt shaked at 200 rpm than in non-shaked yogurt. Finally, this study indicates that temperature and shaking during delivery of yogurt may be critical in keeping quality of yogurt.

• Applied Biological Chemistry
• /
• v.49 no.1
• /
• pp.49-54
• /
• 2006

Physicochemical properties of cross-linked rice starches were investigated. Swelling power of cross-linked rice starch increased at relatively lower temperature $(60^{\circ}C)$ than native rice starch $(70^{\circ}C)$. Cross-linked rice starch showed lower solubility $(1.7{\sim}6.1%)$ than native rice starch $(2.2{\sim}13.8%)$ and solubility is not significantly different with the amount of phosphorus oxychloride. Pasting temperature $(69.2{\sim}70.6^{\circ}C)$ and peak viscosity $(2,874{\sim}3,175\;cp)$ of cross-linked rice starch were lower than native starch $(71.6^{\circ}C,\;3,976\;cp)$, but holding strength $(2,177{\sim}2,708\;cp)$ and final viscosity $(3,424{\sim}3,826 \;cp)$ of cross-linked rice starch were higher than native starch (1,000 cp, 2,312 cp). DSC thermal transitions of cross-linked rice starches were shifted to a lower temperature than native rice starch but there was no significant difference in gelatinization enthalpy between native and cross-linked rice starches. X-ray diffraction pattern of both native and cross-linked rice starches showed typical A-type crystal indicating that cross-linking had not affected the crystalline region of starch.

• Clean Technology
• /
• v.17 no.2
• /
• pp.85-96
• /
• 2011

Self-healing materials are a class of smart materials that have the structurally incorporated ability to repair damage caused by mechanical usage over time. A material (polymers, ceramics, metals, etc.) that can intrinsically correct damage caused by normal usage could lower production costs of a number of different industrial processes through longer part lifetime, reduction of inefficiency over time caused by degradation, as well as prevent costs incurred by material failure. The recent announcement from Nissan on the commercial release of scratch healing paints for use on car bodies has gained public interest on such a wonderful property of materials. This article is a second part of healing materials dealing with inorganic engineering materials such as metals, ceramics, and concrete. The healing mechanisms developed for the inorganic materials are to be discussed with the future prospect.

• Journal of the Korean Ceramic Society
• /
• v.44 no.1 s.296
• /
• pp.52-57
• /
• 2007

We synthesized $(La_{1-x}Sr_x)MnO_3$ as a cathode for SOFC by glycine nitrate process (GNP) and knew the different properties of $(La_{1-x}Sr_x)MnO_3$ by using nitrate solution and oxide solution as a starting material. In case of using nitrate solution as a starting material, main crystal phase peak of $LaMnO_3$ increased as Sr content added up and a peak of $Sr_2MnO_4\;and\;La_2O_3$ was showed as a secondary phase. We added Mn excess to control a crystal phase. In this case, the electrical conductivity had a high value 210.3 S/cm at $700^{\circ}C$. On the other side, when we used oxide solution as a starting material, we found main crystal phase of $LaMnO_3$ to increase as Sr content added up and a peak of $La_2O_3$ as a secondary phase. Similary, we added Mn excess to control a crystal phase in this case. We knew $(La,Sr)MnO_3$ powder to sinter well and the electrical conductivity of the sintered body at $1200^{\circ}C$ for 4 h was 152.7 S/cm at $700^{\circ}C$. The sintered $(La,Sr)MnO_3$ powder at $1000^{\circ}C$ for 4 h got the deoxidization peak, depending on the temperature and in case of using nitrate solution as a starting material, the deoxidization peak was showed at $450^{\circ}C$ which is lower than used a oxide solution as a starting material. As a result, when $(La,Sr)MnO_3$ powder was synthesized to add Mn excess and to use nitrate solution as a starting material, we found it to have the higher deoxidization property and considered it as a cathode for SOFC properly. And we found it to have different electrical conductivity the synthesized $(La,Sr)MnO_3$ powder by using different starting materials like nitrate solution and oxide solution which influence a sintering density and crystal phase.

• Journal of the Korean Magnetics Society
• /
• v.17 no.4
• /
• pp.172-177
• /
• 2007

In order to detect of the magnetic property in the cell unit, we studied the GMR-SV (giant magnetoresistance-spin valves) biosensor, which was depended on the micro patterned features according to two easy directions of longitudinal and transversal axes. Here, the multi layer structure was glass/NiO/NiFe/CoFe/Cu/CoFe/NiFe. The uniaxial anisotropy direction was applied to the patterned biosensor during the deposition and vacuum post-annealing at $200^{\circ}C$ under the magnitude of 300 Oe, respectively. Considering the magnetic shape anisotropy effect, the size of micro patterned biosensor was a $2{\times}5{\mu}m^2$ after the photo lithography process. By our experimental results, we confirmed that the best condition of GMR-SV biosensor should be the same direction of the axis sensing current and the easy axis of pinned NiO/NiFe/CoFe triple layer oriented to the width direction of device, and the direction of the easy axis of free CoFe/NiFe bilayer was according to the longitudinal direction of device.

• Journal of Adhesion and Interface
• /
• v.12 no.3
• /
• pp.88-93
• /
• 2011

Optimal dispersion and fabrication conditions of carbon nanotube (CNT) embedded in phenolic resin were determined by electrical resistance measurement; and interfacial property was investigated between plasma treated carbon fiber and CNT-phenolic composites by electro-micromechanical techniques. Wettability of carbon fiber was improved significantly after plasma treatment. Surface energies of carbon fiber and CNT-phenolic nanocomposites were measured using Wilhelmy plate technique. Since surface activation of carbon fiber, the advancing contact angle decreased from $65^{\circ}$ to $28^{\circ}$ after plasma treatment. It was consistent with static contact angle results of carbon fiber. Work of adhesion between plasma treated carbon fiber and CNT-phenolic nanocomposites was higher than that without modification. The interfacial shear strength (IFSS) and apparent modulus also increased with plasma treatment of carbon fiber.

• Journal of Bio-Environment Control
• /
• v.22 no.3
• /
• pp.284-290
• /
• 2013

This study analyzed the geometric, compressive, cutting and friction properties of oriental melons in order to design a gripper capable of soft handling and a cutter for cutting oriental melon vine among the end effector of oriental melon as a preliminary step for developing the end effector of the robot capable of harvesting oriental melons in protected cultivation. As a result, the average length, diameter at the midpoint, weight, volume and roundness of the oriental melons were 108 mm, 70 mm, 188 g, 333 mL and 3.8 mm. Nonlinear regression analysis was performed on the equation $W=L^a{\times}D_2^b$ with variation of the length (L) and diameter (D2) of the weight (W) of the oriental melons. As a result, it was shown that there was a correlation between a of 2.0279 and b of -0.9998 as a constant value. The average diameter of the oriental melon vine was 3.8 mm, and most vines were distributed within a radius of 5 mm from the center. The average yield value, compressive strength and hardness of the oriental melons were $36.5N/cm^2$, $185.7N/cm^2$ and $636.7N/cm^2$, respectively. The average cutting force and shear strength of the oriental melon vines were $2.87{\times}10^{-2}\;N$ and $5.60N/cm^2$, respectively. The maximum friction coefficient of the oriental melons was rubber of 0.609, followed by aluminium of 0.393, stainless steel of 0.177 and teflon of 0.079. It was considered possible to apply it to the size of the gripper and cutter, turning radius, dynamics of drive motor and selection of materials and their quality in light of the position error and safety factor according to the movement when designing end effector based on the analyzed data.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.7-14
• /
• 2009

In this paper, the effects of annealing conditions on the structural ((002) intensity, FWHM, d-spacing, grain size, (002) peak position), optical (UV peak, UV peak position) and electrical properties (carrier concentrations, resistivity, mobility) of ZnO films were investigated. ZnO films were deposited onto SiO$_2$/si substrates by RF magnetron sputtering from a ZnO target. The substrate was not heated during deposition. ZnO films were annealed in temperature ranges of $500\sim650^{\circ}C$ in the O$_2$ flow for 5$\sim$20 min. The film average thicknesses were in the range of 291 nm. The surface morphologies and structures of the samples were characterize by SEM and XRD, respectively. The optical properties were evaluated by photoluminescence (PL) measurement at room temperature (RT) using a He-Cd 325 nm laser. As the annealing temperature and time vary, the following relations were also observed: (1) proportional relationships among UV intensity (002) intensity, and grain size exist, (2) UV intensity is inversely proportional to FWHM, (3) there is no special relationship between UV intensity and electron carrier concentrations, (4) d-spacing is inversely proportional to (002) peak position, (5) UV peak position in the range of 3.20$\sim$3.24 eV means that ZnO films have a n-type conductivity which was consistent with that obtained from the electrical property, (6) the optimal conditions for the best optical and structural characteristics were found to be oxygen fraction, (O$_2$/(O$_2$+Ar)) of 0.2, RF power of 240W, substrate temperature of RT, annealing condition of 600$^{\circ}C$ for 20 min, and sputtering pressure of 20 mTorr.

• Journal of Periodontal and Implant Science
• /
• v.29 no.1
• /
• pp.209-231
• /
• 1999

Even though titanium(Ti) and its alloys are the most used dental implant materials, there are some problems that Ti wears easily and interferes normal osteogenesis due to the metal ions. Ti coated with bioactive ceramics such as hydroxyapatite has also such problems as the exfoliation or resorption of the coated layer, Recent studies on implant materials have been proceeding to improve physical properties of the implant substrate and biocompatibility of the implant surfaces. The purpose of the present study was to examine the physical property and bone tissue compatibility of bioinert nitrides ion plated Ti, Button type specimens(14mm in diameter, 2.32rrun in height) for the abrasion test and cytotoxicity test and thread type implants(3.75mm in diameter, 6mm in length) for the animal experiments were made from Ti(grade 2) and 316LVM stainless steel. Ti specimens were ion plated with TiN, ZrN by the low temperature arc vapor deposition, and the depth profile of the TiN/Ti, ZrN/Ti ion plated surface was examined by Auger Electron Spectroscopy. Three kind of button type specimens .of TiN/Ti, ZrN/Ti and Ti were used for abrasion test, and HEPAlClC7 cells and CCD cells were cultivated for 4 days with the specimens for cytotoxicity test. Thread type implants of TiN/Ti, ZrN/Ti, Ti, 316LVM were implanted on the femur of 6 adult dogs weighing 10kg-13kg. Two dogs were sacrified for histological examination after 45 days and 90 days, and four dogs were sacrified for the removal torque test of the implant') after 90 days. The removal torque force was measured by Autograph (Shimadzu Co., AGS-1000D series, Japan). Abrasion resistance of TiN/Ti was the highest, and that of ZrN/Ti and Ti were followed. The bioinert nitride ion plated Ti had much better abrasion resistance, compared with Ti, In the cytotoxicity test, the number of both cells were increased in all specimens, and there were no significant difference in cytotoxic reaction among all groups (p>0.1), In histological examination, 316LVM showed the soft tissue engagement in interface between the implant and bone, but the other materials after 45 days noted immature new bone formation in the medullary portion along the implant surface, and those after 90 days showed implant support by new bone formation in both the cortical and the medullary portion, The removal torque force of Tilv/Ti showed significantly higher than that of Ti(p(O,05). The difference in removal torque force between TiN/Ti and ZrN/Ti was not significant(p>0.05), and that of 316LVM was lowest among all groups(p<0.05). These results suggest that bioinert nitrides ion plated Ti can resolve the existing problems of Ti and bioactive ceramics, and it may be clinically applicable to human.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.89-89
• /
• 2012

선행 연구에서는 m-Aramid와 p-Aramid의 Ring 방적사/Core 방적사 조건에 따른 방적사 물성에 대해서 연구하였는데, Ring 방적사의 혼용율, 스핀들 속도에 따른 물성 변화, Core 방적사의 공정특성에 따른 방적성, 피복성에 대해 연구를 하였다. 그 결과 Ring 방적사의 경우 m-Aramid의 혼용율이 증가할수록 사 강도는 증가하는 경향을 확인할 수 있었고, 스핀들 속도가 증가함에 따라서 불균제도 및 사결점이 다소 증가하였다. Core 방적사의 경우 Core에 p-Aramid를 사용했을 때 방적성과 피복성은 양호 하였지만, 강한 p-Aramid에 의해 톱 롤러코트의 마모가 되는 경향을 볼 수 있었다. 본 연구에서는 Ring 방적사/Core 방적사에 대해 좀더 구체적인 제조공정조건에 의한 물성 변화를 알아보았고, 좀더 다양한 섬유소재를 적용해서 제조하였다. Ring 방적사의 경우 p-Aramid 혼용율에 따른 실험을 하였는데, m-Aramid에 대한 p-Aramid의 혼용율을 0%, 5%, 10%, 20% 로 하여 Ne30을 제조하였으며, Core 방적사는 Core를 p-Aramid 200D로 하고 Sheath를 Cotton으로 하여 Core 공급속도비 (1.06, 1.10, 1.14), 연계수(T/M, 3.8, 4.0, 4.2), Sheath/Core 혼섬율(70/30, 60/40, 50/50)에 따라 제조하였다. 추가로 Core 방적사는 Sheath에 Cotton 대신 FR-Rayon과 선염 Cotton을 사용하여 각각 Sheath/Core 혼섬율 70/30의 비율로 방적사를 제조하여 다양한 소재에 따른 방적사의 물성을 측정하였다. 제조된 시험 원사들의 측정 물성은 번수(Ne), 균제도(U%), 사결점(IPI), 강력(cN), 신도(%), 비강도(cN/Tex) 등이며, 편직을 통해 편성물의 외관을 확인하였다. Ring 방적사의 경우 p-Aramid의 혼용율이 증가할수록 강도는 완만하게 증가한 반면, 신도는 급격하게 감소하였다. Cotton Core 방적사의 경우는 공급속도비가 높아질수록 균제도가 높아지는 것을 볼수 있었고, Core 공급속도비가 높아질수록 외관상 피복도는 높아진 것을 볼 수 있었다. 이렇게 연구된 Aramid 소재를 이용한 방적사 제조 공정조건변화에 따른 물성 및 피복도 결과는 기존 방적업체에서 Aramid를 이용한 방적사 제조시에 공정조건을 확보하는데 도움이 될 것이라 생각되며, 방적사 시제품 생산시에 발생할 수 있는 시행착오를 줄임으로써 시제품 제조를 위한 생산비용의 Loss를 절감할 수 있을 것으로 예상된다.