• Journal of Broadcast Engineering
• /
• v.2 no.2
• /
• pp.136-145
• /
• 1997

As a 3D mesh model consists of a lot of vertices and polygons and each vertex position is represented by three 32 bit floating-point numbers in a 3D coordinate, the amount of data needed for representing the model is very excessive. Thus, in order to store and/or transmit the 3D model efficiently, a 3D model compression is necessarily required. In this paper, a 3D model compression method using PRVQ (predictive residual vector quantization) is proposed. Its underlying idea is based on the characteristics such as high correlation between the neighboring vertex positions and the vectorial property inherent to a vertex position. Experimental results show that the proposed method obtains higher compression ratio than that of the existing methods and has the advantage of being capable of transmitting the vertex position data progressively.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.2
• /
• pp.93-100
• /
• 2011

This study deals with the high frequency induction hardening (HF at $850^{\circ}C$, 120kHz & 50kW condition) SM45C steel. (1) The HF specimen, which was tempered at $150^{\circ}C$, did not show any tempering effect. A brittle fracture occurred at rounded area of the tensile specimen. AE (acoustic emission) amplitude distribution showed between 45dB and 60dB. (2) A slip and fracture occurred at the hole area of the HF specimen which was tempered at $300^{\circ}C$. As they pass the yield point, the AE energy is increased intermittently and AE amplitude distribution exists between 70dB and 85dB. In addition, after imposing the maximum tensile load, AE signals showed high amplitude and energy distribution. The AE amplitude showed between 45dB and 70dB. (3) A brittle fracture occurred at HF specimen which was tempered at $450^{\circ}C$ as if it is torn in the direction of $45^{\circ}$ on parallel area over the both sides of the tensile specimen, which lead to several peak appeared in AE energy. It was found that the AE amplitude was relatively low and the AE energy was high.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.161-161
• /
• 2010

InAsSb alloy system 은 HgCdTe 를 대체하는 적외선 광소자 및 검출기 등에 응용이 가능한 유망한 물질이지만 정확한 유전함수 및 전이점의 연구는 미흡한 실정이다. 본 연구에서는 타원 편광 분석법을 이용하여 1.5 ~ 6 eV 의 분광 영역에서 As 조성비를 각기 (x = 0, 0.127, 0.337, 0.491, 0.726 및 1.00) 다르게 한 $InAs_xSb_{1-x}$ alloy의 유전함수를 측정하였다. 또한 표면에 자연산화막을 제거하기 위하여 Methanol 과 DI Water 로 표면을 세척 한 후 $NH_4OH$, Br in Methanol, HCl 등으로 적절한 화학적 에칭을 하여 산화막을 제거함으로서 순수한 InAsSb 의 유전함수를 측정할 수 있었다. 측정된 InAsSb 유전함수를 Standard analytic critical point line shape 방법으로 As 조성비에 따른 에너지 전이점을 얻을 수 있었다. 또한 얻어진 에너지 전이점 값을 이용하여 linear augmented Slater-type orbital 방법으로 전자 밴드 구조 계산을 하였고, 이를 바탕으로 $E_0$, $E_1$, $E_2$ 전이점 지역의 여러 전이점 ($E_1$, $E_1+\Delta_1$, $E_0'$, $E_0'+\Delta_0'$, $E_2$, $E_2+\Delta_2$, $E_2'$, $E_2'+\Delta_2$, $E_1'$) 의 특성을 정확히 정의할 수 있었다. 또한 As 조성비가 증가하면서 $E_2$, $E_2+\Delta_2$, $E_2'$, $E_2'+\Delta_2$ 전이점들이 서로 교차 되는 것을 발견하였고, 저온에서만 관측이 가능하였던 InSb 의 두 saddle-point (${\Delta_5}^{cu}-{\Delta_5}^{vu}$, ${\Delta_5}^{cl}-{\Delta_5}^{vu}$)를 상온에서 찾아내었다. 타원 편광 분석법을 이용한 전이점 연구 및 물성 분석은 InAsSb alloy 의 광학적 데이터베이스를 확보하는 성과와 더불어 새로운 디바이스기술 및 광통신 산업에도 유용한 정보가 될 것이다.

• Journal of computational fluids engineering
• /
• v.12 no.3
• /
• pp.41-46
• /
• 2007

Dynamic behavior of immiscible gas bubble attached to the wall in channel flow plays very important role in many engineering applications. Special attention has been paid to micro direct methanol fuel cell(${\mu}$DMFC) where surface tension becomes dominant factor with minor gravitational effect due to its reduced size. Therefore, displacement of $CO_2$ bubble generating on a cathode side in ${\mu}$DMFC can be very difficult and efficient removal of $CO_2$ bubbles will affect the overall machine performance considerably. We have focused our efforts on studying the dynamic behavior of immiscible bubble attached to the one side of the wall on 2D rectangular channel subject to external shear flow. We used Level Contour Reconstruction Method(LCRM) which is the simplified version of front tracking method to track the bubble interface motion. Effects of Reynolds number, Weber number, advancing/receding contact angle and property ratio on bubble detachment characteristic has been numerically identified.

• Archives of Pharmacal Research
• /
• v.25 no.5
• /
• pp.636-639
• /
• 2002

The extract of the root of Polygonum multiflorum exhibited a significant antioxidant activity assessed by the DPPH radical scavenging activity in vitro. The bioassay-guided fractionation of the extract yielded a stilbene glucoside, (E)-2,3,5,4'-tetrahydroxystilbene-2-Ο-$\beta$-d-glucopyranoside (1) as an active constituent responsible for the antioxidant property. Compound 1 demonstrated a moderate DPPH radical scavenging activity ($IC_{50}$, 40 $\mu$M), while the corresponding deglucosylated stilbene 2 exhibited a much higher activity ($IC_{50}$, 0.38 $\mu$M).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.4
• /
• pp.325-336
• /
• 2013

FlashLinQ, one of the typical D2D communication systems developed by Qualcomm, considers a single-tone communication based distributed channel-aware link scheduling method to realize the link scheduling process with low control overheads. However, considering the frequency selective fading effect of practical multi-path channel, the single-tone based SIR estimation causes a critical scheduling error problem because the received single-tone signal has quite different channel gain at each sub-carrier location. In order to overcome this problem, we propose a novel link scheduling method based on CAZAC (Constant Amplitude Zero Auto-Correlation) sequence for D2D communication system. In the proposed method, each link has a unique offset value set for the generation of CAZAC sequences. CAZAC sequences with the cyclic offsets are transmitted using multiple sub-blocks in the entire bandwidth, and then each device can obtain nearly full-band SIR using a good cyclic cross-correlation property of CAZAC sequence.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.2
• /
• pp.293-298
• /
• 2001

EB-NMP free standing film is manufactured from NMP solution of polyaniline(emeraldine base EB). Also ES(emeraldine salt EB . HCl) film is manufactured by doping of EB-NMP film with 1 mole HCI aqueous solution. And EB-mixture films containing conductor(carbon black, graphite, Ag etc.) are prepared, In this study, electromagnetic interference shielding efficiency(EMI SE) of ES free standing film ($\sigma$=5 S/cm, t=0.14mm) is 23~25 dB in the frequency range of 10 MHz~1 GHz. ES-mixture(carbon black, graphite, Ag etc.) films, polyaniline film doped camphorsulfonic acid(CSA) show higher EMI SE(30~34 dB, 36~42 dB, 44~52 dB, 34~43 dB) property than that of ES free standing film, respectively.

• Korean Journal of Materials Research
• /
• v.27 no.10
• /
• pp.534-543
• /
• 2017

$Gd_2O_3:Eu^{3+}$ red phosphors were prepared by template method from crystalline cellulose impregnated by metal salt. The crystallite size and photoluminescence(PL) property of $Gd_2O_3:Eu^{3+}$ red phosphors were controlled by varying the calcination temperature and $Eu^{3+}$ mol ratio. The nano dispersion of $Gd_2O_3:Eu^{3+}$ was also conducted with a bead mill wet process. Dependent on the time of bead milling, $Gd_2O_3:Eu^{3+}$ nanosol of around 100 nm (median particle size : $D_{50}$) was produced. As the bead milling process proceeded, the luminescent efficiency decreased due to the low crystallinity of the $Gd_2O_3:Eu^{3+}$ nanoparticles. In spite of the low PL property of $Gd_2O_3:Eu^{3+}$ nanosol, it was observed that the photoluminescent property was recovered after re-calcination. In addition, in the dispersed nanosol treated at $85^{\circ}C$, a self assembly phenomenon between particles appeared, and the particles changed from spherical to rod-shaped. These results indicate that particle growth occurs due to mutual assembly of $Gd(OH)_3$ particles, which is the hydration of $Gd_2O_3$ particles, in aqueous solvent at $85^{\circ}C$.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.17-22
• /
• 2006

Shear modulus is directly linked to material's stiffness and is one of the most critical engineering parameters. Seismically, shear-wave velocity (Vs) is its best indicator. Although methods like refraction, down-hole, and cross-hole shear-wave surveys can be used, they are generally known to be tougher than any other seismic methods in field operation, data analysis, and overall cost. On the other hand, surface waves, commonly known as ground roll, are always generated in all seismic surveys with the strongest energy, and their propagation velocities are mainly determined by Vs of the medium. Furthermore, sampling depth of a particular frequency component of surface waves is in direct proportion to its wavelength and this property makes the surface wave velocity frequency dependent, i.e., dispersive. The multichannel analysis of surface waves (MASW) method tries to utilize this dispersion property of surface waves for the purpose of Vs profiling in 1-D (depth) or 2-D (depth and surface location) format. The active MASW method generates surface waves actively by using an impact source like sledgehammer, whereas the passive method utilizes those generated passively by cultural (e.g., traffic) or natural (e.g., thunder and tidal motion) activities. Investigation depth is usually shallower than 30 m with the active method, whereas it can reach a few hundred meters with the passive method. Overall procedures with both methods are briefly described.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.161-162
• /
• 2005

2G HTS coated conductor wire consists of textured substrate, buffer layer, superconduct layer, Ag cap layer, stabilizer. For practical application filed, coated conductor have mechanical and electrical stability and environment protection properties. This property Cu and stainless steel strip is laminated to Ag cap layer as stabilizer materials. Lamination process join stabilizer material strip and Ag cap layer with soldering method. we have laminated HTS with continuous dipping soldering process different stabilizer Cu and stainless steel strip and changed lamination process condition. The effect of lamination stabilizer and process condition has been investigated mechanical and electrical properties.