• Journal of KSNVE
• /
• v.9 no.2
• /
• pp.317-323
• /
• 1999

Dynamic characteristics of catenary that supplies electrical power to high-speed trains are investigated. A simple catenary is composed of the contact and messenger wires connected by droppers possessing bi-directional stiffness properties. For slender, repeating structures such as catenary, both the wave propagation and vibration properties need to be understood. The influence of parameters that determine catenary dynamics are investiaged through numerical simulations involving finite element models. The effects of the tension and flexural rigidity of the contact wire is first investigated. The effects of dropper characteristics are then investigated. For linear droppers wave propagation as well as modal properties are determined. For large catenary motion, droppers can be modeled as bi-directional elements possessing low stiffness in compression and high stiffness in tension. For this case, impulse response is computed and compared with the cases of linear droppers. It is found that the catenary dynamics are primarily determined by contact wire tension and dropper properties, with large responses observed in 5∼40 Hz frequency range. In particular, the dropper stiffness and spacing are found to have dominant influence on the response frequency and the wave transmission characteristics.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2010.10a
• /
• pp.27-27
• /
• 2010

There have been several studies about empirical relation between seismic source parameters(e.g., focal mechanisms, depths, magnitudes, etc.) and T-wave observation. In order to delineate the relation, numerical and theoretical approaches to figure out T-wave excitation mechanism are required. In an attempt to investigate source radiation and wave scattering effects in the oceanic crust on T-wave envelopes, we perform three-dimensional numerical modeling to synthesize T-wave envelopes. We first calculate seismic P- and SV-wave energy on the seafloor using the Direct Simulation Monte Carlo based on the Radiative Transfer Theory, which enables us to take into account both realistic seismic source parameters and wave scattering in heterogeneous media, and then estimate excited T-wave energy by normal mode computation. The numerical simulation has been carried out considering the following different conditions: source types (strike and normal faults), source depths (shallow and deep), and wave propagation through homogeneous and heterogeneous Earth media. From the results of numerical modeling, we confirmed that T-wave envelopes vary according to spatial seismic energy distributions on the seafloor for the various input parameters. Furthermore, the synthesized T-wave envelopes show directional patterns due to anisotropic source radiation, and the slope change of T-wave envelopes caused by focal depth. Seismic wave scattering in the oceanic crust is likely to control the shape of envelopes.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1412-1421
• /
• 2018

Cold-expanded austenitic high nitrogen steel (HNS) was subjected to investigate the effects of grain size on the stress-controlled high cycle fatigue (HCF) as well as the strain-controlled low cycle fatigue (LCF) properties. The austenitic HNSs with two different grain sizes (160 and $292{\mu}m$) were fabricated by the different hot forging strain. The fine-grained (FG) specimen exhibited longer LCF life and higher HCF limit than those of the coarse-grained (CG) specimen. Fatigue crack growth testing showed that crack propagation rate in the FG specimen was the same as that in the CG specimen, implying that crack propagation rate did not affect the discrepancy of LCF life and HCF limit between two cold-expanded HNSs. Therefore, it was estimated that superior LCF and HCF properties in the FG specimen resulted from the retardation of the fatigue crack initiation as compared with the CG specimen. Transmission electron microscopy showed that the effective grain size including twin boundaries are much finer in the FG specimen than that in the CG specimen, which can give favorable contributions to strengthening.

• Advances in Computational Design
• /
• v.4 no.2
• /
• pp.141-153
• /
• 2019

This research is comprised of virtually simulating behavior while experiencing low gravity effects in advance of real world testing in low gravity aboard Zero Gravity Corporation's (Zero-G) research aircraft (727-200F). The experiment simulated a drill rig penetrating a regolith simulant. Regolith is a layer of loose, heterogeneous superficial deposits covering solid rock on surfaces of the Earth' moon, asteroids and Mars. The behavior and propagation of space debris when drilled in low gravity was tested through simulations and visualization in a leading dynamic simulation software as well as discrete element modeling software and in preparation for comparing to real world results from flying the experiment aboard Zero-G. The study of outer space regolith could lead to deeper scientific knowledge of extra-terrestrial surfaces, which could lead us to breakthroughs with respect to space mining or in-situ resource utilization (ISRU). These studies aimed to test and evaluate the drilling process in low to zero gravity environments and to determine static stress analysis on the drill when tested in low gravity environments. These tests and simulations were conducted by a team from Texas A&M University's Department of Construction Science, the United States Air Force Academy's Department of Astronautical Engineering, and Crow Industries

• Advances in nano research
• /
• v.10 no.3
• /
• pp.271-280
• /
• 2021

The present work deals with an investigation on longitudinal wave propagation in nanobeams made of graphene sheets, for the first time. The nanobeam is modelled via a higher-order shear deformation theory accounts for both higher-order and thickness stretching terms. The general nonlocal strain gradient theory including nonlocality and strain gradient characteristics of size-dependency in order is used to examine the small-scale effects. This model has three-small scale coefficients in which two of them are for nonlocality and one of them applied for gradient effects. Hamilton supposition is applied to obtain the governing motion equation which is solved using a harmonic solution procedure. It is indicated that the longitudinal wave characteristics of the nanobeams are significantly influenced by the nonlocal parameters and strain gradient parameter. It is shown that higher nonlocal parameter is more efficient than lower nonlocal parameter to change longitudinal phase velocities, while the strain gradient parameter is the determining factor for their efficiency on the results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5B
• /
• pp.551-555
• /
• 2006

In this study, new dispersion-correction terms are added to a leap-frog finite difference scheme for the linear shallow-water equations with the purpose of considering dispersion effects of the linear Boussinesq equations for propagation of tsunamis. The numerical model developed in this study is tested to the problem that the initial free surface displacement is a Gaussian hump over a constant water depth, and the predicted numerical results are compared with analytical solutions. The results of the present numerical model are accurate in comparison with those of existing models.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.6
• /
• pp.512-519
• /
• 2013

It is important to understand the vibrating behavior of plate structures for its many engineering applications. In this study, the vibration characteristics of strip plates that have finite width and infinite length are investigated theoretically and numerically. The waveguide finite element(WFE) approach, which is an effective tool for studying waveguide structures, is used in this study. The WFE method requires only a cross-sectional finite element model, and uses theoretical harmonic solutions to assess wave propagation along the longitudinal direction. First, WFE results for a simple strip plate are compared with the theoretical results(i.e., dispersion diagrams and point mobilities) to validate the numerical model. Then, in the numerical analysis, different numbers of longitudinal stiffeners are included in the plate model to investigate the effects of stiffeners in terms of the dispersion curves and mobilities. Finally, the dispersion curves of a stiffened double plate are obtained to examine the characteristics of its wave propagation.

• Smart Structures and Systems
• /
• v.20 no.3
• /
• pp.329-342
• /
• 2017

In this paper, the dispersion characteristics of elastic waves propagation in sandwich nano-beams with functionally graded (FG) face-sheets reinforced with carbon nanotubes (CNTs) is investigated based on various high order shear deformation beam theories (HOSDBTs) as well as nonlocal strain gradient theory (NSGT). In order to align CNTs as symmetric and asymmetric in top and bottom face-sheets with respect to neutral geometric axis of the sandwich nano-beam, various patterns are employed in this analysis. The sandwich nano-beam resting on Pasternak foundation is subjected to thermal, magnetic and electrical fields. In order to involve small scale parameter in governing equations, the NSGT is employed for this analysis. The governing equations of motion are derived using Hamilton's principle based on various HSDBTs. Then the governing equations are solved using analytical method. A detailed parametric study is conducted to study the effects of length scale parameter, different HSDBTs, the nonlocal parameter, various aligning of CNTs in thickness direction of face-sheets, different volume fraction of CNTs, foundation stiffness, applied voltage, magnetic intensity field and temperature change on the wave propagation characteristics of sandwich nano-beam. Also cut-off frequency and phase velocity are investigated in detail. According to results obtained, UU and VA patterns have the same cut-off frequency value but AV pattern has the lower value with respect to them.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.2
• /
• pp.135-143
• /
• 2020

Natural drought is a three-dimensional phenomenon that simultaneously evolves in time and space. To evaluate the link between meteorological and hydrological droughts, we defined a drought event from a three-dimensional perspective and analyzed the propagation characteristics in time and spaces. Overall results indicated that 77 % of the total cases of spatio-temporal droughts was propagated based on the single category relationship between meteorological and hydrological drought events, while 23 % was affected by multiple meteorological drought events to the occurrence of hydrological drougts. Especially, it turned out that the hydrological drought was caused by the spatio-temporal effects of the propagation of four meteorological drought events generated due to long-term lack of precipitation in 1994-1995. In addition, the meteorological drought caused by the lack of precipitation in the summer of 2001 lasted for several months, and was propagated to the hydrological drought in April 2002.

• Journal of Welding and Joining
• /
• v.29 no.2
• /
• pp.46-55
• /
• 2011

This paper deals with the crack propagation life assessment of T-joint welded structure where typical fatigue cracks have been frequently initiated when the marine vessels experience the storm load. Welding residual stresses are calculated to investigate its effects on the fatigue life. Thereafter the residual stress distribution was applied to the AFGROW life prediction program, which incorporated the loading, the welding residual stress, and the geometric shape of the structure. The fatigue tests of the T-joint welded specimen under storm loading show the beach mark clearly generated on the fractured section of the weldment. The crack propagation life estimated based on the beach mark is compared with that of AFGROW to validate the life prediction. Based on the results, the evaluation method of the remaining fatigue life for T-joint fillet weldment of marine vessel's cargo hold with random load or storm load was established.