• Journal of Bio-Environment Control
• /
• v.29 no.4
• /
• pp.326-336
• /
• 2020

This study was conducted to investigate productivity of strawberry plants as affected by propagation method and cultivation system. Transplants propagated by cutting propagation and pinning propagation were planted and grown for a whole production period in soil and hydroponic cultivation systems. Growth parameters, fruit productivity, and fruit quality were measured during the whole harvest period. The results showed that propagation method and cultivation system had significant effects on vegetative growth of strawberry plants. Total fruit yield per plant and average fruit weight per fruit during the whole harvest period were significantly lower in the plants grown in soil cultivation system. Total unmarketable fruit ratio was significantly greater in soil cultivation system than that in hydroponic cultivation system. Small fruits were the primary unmarketable fruits in soil cultivation system, while malformed fruits were the primary unmarketable fruits in hydroponic cultivation system. The overall high quality of fruit was found in February, and the plants cultivated in hydroponic cultivation system had higher quality of fruit as compared with that in soil cultivation system. It is concluded that cutting propagation is better than pinning propagation, and hydroponic cultivation system is better than soil cultivation system for fruit productivity of strawberry.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.8
• /
• pp.682-685
• /
• 1996

Photothermal properties depend on the characteristics of energy transfer processes in solution. In this study, a time-resolved single beam thermal lens experiment in various solvents is employed to investigate the energy coupling effects which govern the energy transfer processes. Interestingly, it is observed that the behaviour of the photothermal propagation in solution depends on the property of solution and the concentration of solute in a single beam thermal lens configuration. These characteristics lead us to consider the solute-solvent coupling effects as well as the solvent-solvent interactions.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.11
• /
• pp.41-48
• /
• 2005

The crosstalk effects that can be observed in the very dee submicron semiconductor chips are due to the coupling capacitances between interconnect lines. The accuracy of the full-chip timing analysis is determined by the accuracy of the estimated propagation delays of cells and interconnects within the chip. This paper presents a CMOS cell driver model and delay calculation algerian capturing the crosstalk effects due to the coupling capacitances. The proposed model and algorithm were implemented in a delay calculation program and used to estimate the propagation delays of the benchmark circuits extracted from a chip layout. We observed that the average discrepancy from HSPICE simulation results is within $1\%$ for the circuits with a victim affected by $0\~10$ aggressors.

• Smart Structures and Systems
• /
• v.16 no.5
• /
• pp.835-851
• /
• 2015

This paper presents theoretical and experimental evaluation of the structural health monitoring (SHM) capability of piezoelectric wafer active sensors (PWAS) at elevated temperatures. This is important because the technologies for structural sensing and monitoring need to account for the thermal effect and compensate for it. Permanently installed PWAS transducers have been One of the extensively employed sensor technologies for in-situ continuous SHM. In this paper, the electro-mechanical impedance spectroscopy (EMIS) method has been utilized as a dynamic descriptor of PWAS behavior and as a high frequency standing wave local modal technique. Another SHM technology utilizes PWAS as far-field transient transducers to excite and detect guided waves propagating through the structure. This paper first presents how the EMIS method is used to qualify and quantify circular PWAS resonators in an increasing temperature environment up to 230 deg C. The piezoelectric material degradation with temperature was investigated and trends of variation with temperature were deduced from experimental measurements. These effects were introduced in a wave propagation simulation software called Wave Form Revealer (WFR). The thermal effects on the substrate material were also considered. Thus, the changes in the propagating guided wave signal at various temperatures could be simulated. The paper ends with summary and conclusions followed by suggestions for further work.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.622-624
• /
• 2008

This investigation studies the effects of material properties and corresponding propagation wave types on optimal configurations of sound absorbing porous materials in maximizing the absorption performance by topology optimization. The acoustic behavior of porous materials is characterized by their material properties which determine motions of the frame and the air. When the frame has a motion, two types of compressional wave propagate in the porous material. Because each wave in the material make different influence on the absorption performance, it is important to understand the relative contribution of each wave to the sound absorption. The relative contribution of the propagating waves in a porous material is determined by the material properties, therefore, an optimal configuration of a porous material to maximize the absorption performance is apparently affected by the material properties. In fact, virtually different optimal configurations were obtained for absorption coefficient maximization when the topology optimization method developed by the authors was applied to porous materials having different material properties. In this investigation, some preliminary results to explain the findings are presented. Although several factors should be considered, the present investigation is focused on the effects of the material properties and corresponding propagation waves on the optimized configurations.

• Advances in nano research
• /
• v.7 no.3
• /
• pp.157-167
• /
• 2019

In this paper, a classical plate model is utilized to formulate the wave propagation problem of magnetostrictive sandwich nanoplates (MSNPs) while subjected to hygrothermal loading with respect to the scale effects. Herein, magnetostriction effect is considered and controlled on the basis of a feedback control system. The nanoplate is supposed to be embedded on a visco-Pasternak substrate. The kinematic relations are derived based on the Kirchhoff plate theory; also, combining these obtained equations with Hamilton's principle, the local equations of motion are achieved. According to a nonlocal strain gradient theory (NSGT), the small scale influences are covered precisely by introducing two scale coefficients. Afterwards, the nonlocal governing equations can be derived coupling the local equations with those of the NSGT. Applying an analytical solution, the wave frequency and phase velocity of propagated waves can be gathered solving an eigenvalue problem. On the other hand, accuracy and efficiency of presented model is verified by setting a comparison between the obtained results with those of previous published researches. Effects of different variants are plotted in some figures and the highlights are discussed in detail.

• Journal of Internet Computing and Services
• /
• v.15 no.1
• /
• pp.125-134
• /
• 2014

As the social media which was simple communication media is activated on account of twitter and facebook, it's usability and importance are growing recently. Although many companies are making full use of its the capacity of information diffusion for marketing, the adverse effects of this capacity are growing. Because social network is formed and communicates based on friendships and relationships, the spreading speed of the spam and mal-ware is very swift. In this paper, we draw parameters affecting malicious data diffusion in social network environment, and compare and analyze the diffusion capacity of each parameters by propagation experiment with XSS Worm and Koobface Worm. In addition, we discuss the structural characteristics of social network environment and then proposed malicious data propagation model based on parameters affecting information diffusion. n this paper, we made up BA and HK models based on SI model, dynamic model, to conduct the experiments, and as a result of the experiments it was proved that parameters which effect on propagation of XSS Worm and Koobface Worm are clustering coefficient and closeness centrality.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.146-153
• /
• 1998

The optical near-field patterns, propagation loss and mode sizes of x-cut $Ti:LiNbO_3$ optical waveguide which was fabricated by Ti-diffusion varying with Ti strip thickness in wet oxygen atmosphere were discussed at optical wavelength 1550nm. As Ti thickness increased from $760{\AA}$, the insertion loss of waveguide was decreased. But at Ti thickness $1500{\AA}$, mode sizes are widely broadened. The Ti thickness of below $1100{\AA}$ and above $1500{\AA}$ showed negative effects to propagation loss and fiber coupling. The best Ti thickness for fabricating low propagation loss and good fiber coupling was inferred to be between $1100{\AA}-1500{\AA}$ in our conditions. And for Ti thickness $1150{\AA}$, its propagation loss, horizontal/vertical mode sizes were showed 1.61 dB/cm, $11.9/8.9{\mu}m$ for TM, 0.22 dB/cm, $12.0/9.1{\mu}m$ for TE respectively.

• Earthquakes and Structures
• /
• v.15 no.4
• /
• pp.369-382
• /
• 2018

A free vibration analysis and wave propagation of functionally graded porous beams has been presented in this work using a high order hyperbolic shear deformation theory. Unlike other conventional shear deformation theories, a new displacement field that introduces indeterminate integral variables has been used to minimize the number of unknowns. The constituent materials of the beam are assumed gradually variable along the direction of height according to a simple power law distribution in terms of the volume fractions of the constituents. The variation of the pores in the direction of the thickness influences the mechanical properties. It is therefore necessary to predict the effect of porosity on vibratory behavior and wave velocity of FG beams in this study. A new function of the porosity factor has been developed. Hamilton's principle is used for the development of wave propagation equations in the functionally graded beam. The analytical dispersion relationship of the FG beam is obtained by solving an eigenvalue problem. Illustrative numerical examples are given to show the effects of volume fraction distributions, beam height, wave number, and porosity on free vibration and wave propagation in a functionally graded beam.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.188-197
• /
• 2016

In this paper, we propose a method that represents a mathematical form of wave propagation by using the fact the refractive index determining wave propagation characteristic is a function of altitude. Proposed method uses Snell's law that expresses relationship between incident angle and refraction angle when incident wave passes medium having a different refractive index. We present the simulation results about wave propagation by setting the square of refractive index in the form of the polynomial for altitude and show that it is possible to estimate the coefficients of the polynomial through the angle information from vertical axis of multiple radar systems.