• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.1
• /
• pp.60-73
• /
• 2014

The seaward reverse wave, occurring on the submerged dual porous horizontal plate, can contribute to the reduction of the transmitted wave as it reflects the propagating wave. However, the collision between the propagating and seaward reverse waves increases the water level and acts as a weight on the horizontal plate. This study investigated the characteristics of the wave pressure created by the seaward reverse wave through the analysis of experimental data. The analysis confirmed the following results: 1) the time series of the wave pressure showed reverse phase phenomena due to the collision, and the wave pressures acted simultaneously on both upper and lower surfaces of the horizontal plate; 2) the horizontal plate became repeatedly compressed and tensile before and after the occurrence of the seaward reverse wave; and 3) the seaward reverse wave created the total wave pressure to the maximum towards the direction of gravity, primarily on the upper plate. It was also confirmed that the wave distributions showed a similar trend to the wave steepness. Such outcome of the analysis will provide basic information to the structural analysis of the horizontal plate as a wave dissipater of the steel-type breakwater (STB).

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.1
• /
• pp.51-58
• /
• 2003

The magnitude of evanescent modes in terms of dynamics it investigated in case that the transformation of water waves is predicted by the linear wave theory. For the waves propagating over two steps, the eigenfunction expansion method is used to predict the amplitudes of reflected and transmitted waves by the component of evanescent modes as well as propagating modes. Then. the relative importance of evanescent modes to the propagating modes is investigated. The numerical experiments find that the evanescent modes are pronounced at the relative water depth of k$_1$h$_1$＝0.11$\pi$ and the water depth ratio of h$_2$/h$_1$ close to zero.

• Journal of Navigation and Port Research
• /
• v.27 no.6
• /
• pp.677-682
• /
• 2003

The long-period gravity wave, the wave period from some ten seconds to some minutes, induces not only the big sway of a ship moored and berthed in the harbor due to the horizontal long-distance motion of a water but also strong exfoliated flow and vortices near the harbor entrance. They muse serious problems on the safety navigation of vessels entering and leaving the harbor, but this gravity wave has not been searched sufficiently yet. Then it is quite important to reveal the characteristics of this long-period gravity wave ana to solve various problems induced by this wave. The long-period gravity wave measurement system with arrayed buoys installed the kinematic GPS was already proposed, which provides the precise propagating direction of the long-period gravity wave. In this paper, the observation results of the wave measurement system are shown by the MUSIC method And the propagating wave direction was estimated precisely enough in comparison with other results used other method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2686-2697
• /
• 1994

When a railway train enters a tunnel at high speed, a compression wave is formed in front of the train and propagates along the tunnel. The compression wave subsequently emerges from the exit of the tunnel, which causes an impulsive noise. In order to estimate the magnitudes of the noises and to effectively minimize them, the characteristics of the compression wave propagating in a tunnel must be understood. In the present paper, the experimental and analytical investigations on the attenuation and distortion of the propagating compression waves were carried out using a model tunnel. This facility is a kind of open-ended shock tube with a fast-opening gate valve instead of a general diaphragm. One-dimensional flow model employed in the present study could appropriately predict the strength of the compression wave, Mach number and flow velocity induced by the compression wave. The experimental results show that the strength of a compression wave decreases with the distance from the tunnel entrance. The decreasing rate of the wave strength and pressure gradient in the wave is strongly dependent on the strength of the initial compression wave at the tunnel entrance.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.456-461
• /
• 2001

This paper depicts the weak shock wave propagating inside some kinds of pipe bends. Computational work is to solve the two-dimensional, compressible, unsteady Euler Equations. The second-order TVD scheme is employed to discretize the governing equations. For the computations, the incident normal shock wave is assumed at the entrance of the pipe bend, and its Mach number is changed between 1.1 and 1.7. The turning angle and radius of the curvature of the pipe bend are changed to investigate the effects on the shock wave structure. The present computational results clearly show the shock wave reflection and diffraction occurring in the pipe bend. In particular, the vortex generation, which occurs at the edge of the bend, and its shedding mechanism are discussed in details.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.5 s.66
• /
• pp.26-33
• /
• 2005

Attenuation of fundamental longitudinal guided wave propagating liquid-filled steel pipes is numerically investigated. Several liquids such as water, diesel oil, castor oil etc. are considered for the filing materials in the pipes. Sink is considered for numerical models for abandoning standing wave modes; hence the attenuation dispersion curves become much simpler. Those attenuation calculations can be utilized for guided-wave-based nondestructive testing of pipelines when one inspects pipelines, using monitoring sensors, which are installed outside pipes.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.435-447
• /
• 2019

Energy Flow Finite Element Analysis (EFFEA) is a promising tool for predicting dynamic energetics of complicated structures at high frequencies. In this paper, the Energy Flow Finite Element (EFFE) formulation of complicated Mindlin plates was newly developed to improve the accuracy of prediction of the dynamic characteristics in the high frequency. Wave transmission analysis was performed for all waves in complicated Mindlin plates. Advanced Energy Flow Analysis System (AEFAS), an exclusive EFFEA software, was implemented using $MATLAB^{(R)}$. To verify the general power transfer relationship derived, wave transmission analysis of coupled semi-infinite Mindlin plates was performed. For numerical verification of EFFE formulation derived and EFFEA software developed, numerical analyses were performed for various cases where coupled Mindlin plates were excited by a harmonic point force. Energy flow finite element solutions for coupled Mindlin plates were compared with the energy flow solutions in the various conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.8
• /
• pp.1972-1981
• /
• 1995

As a railway train enters a tunnel at high speed, a compression wave is formed in front of the train and propagates along the tunnel. The compression wave subsequently emerges from the exit of the tunnel, which causes an impulsive noise. The impulsive noise is closely related to the pressure gradient of the compression wave propagating the tunnel. In order to investigate the characteristics of the compression waves, in the present study an experiment was made using a shock tube. The results show that the strength of a compression wave decreases with the distance from the tunnel entrance and the nonlinear effect of compression wave appears to be significant if strength of the initial compression wave is greater than 7 kPa. Furthermore if the wave pattern is known, attenuation of the compression wave propagating in a tunnel can be reasonably predicted by a theoretical equation considering viscous action and heat transfer in boundary layer.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.634-639
• /
• 2001

The current study addresses experimental and computational work of impulse wave discharged from the exit of two kinds of right-angle pipe bends, which are attached to the open end of a simple shock tube. The weak normal shock wave with its magnitude of Mach number from 1.02 to 1.20 is employed to obtain the impulse wave propagating outside the exit of the pipe bends. A Schlieren optical system visualizes the impulse wave discharged from the exit of the pipe bends at an instant. The experimental data of the magnitude of the impulse wave and its propagating directivity are analyzed to characterize the impulse waves discharged from the exit of the pipe bends and compared with those discharged from a straight pipe. Computational results well predict the experimented dynamic behaviors of the impulse wave. The results obtained show that a right-angle miter bend considerably reduces the magnitude of the impulse wave and its directivity toward to the pipe axis, compared with the straight pipe and right-angle smooth bend. It is believed that the right-angle miter bend pipe can playa role of a passive control against the impulse wave.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.9
• /
• pp.1139-1148
• /
• 1997

Compression waves propagating in a high-speed railway tunnel develops large pressure fluctuations on the train body or tunnel structures. The pressure fluctuations would cause an ear discomfort for the passengers and increase the aerodynamic resistance of trains. As a fundamental research to resolve the pressure wave phenomenon in the tunnel, experiments were carried out by using a shock tube with an open end. A blockage to model trains inside the tunnel was installed on the lower wall of shock tube, thus forming a sudden cross-sectional area reduction. The compression waves were obtained by the fast opening gate valve instead of a conventional diaphragm of shock tube and measured by the flush mounted pressure transducers with a high sensitivity. The experimental results were compared with the previous theoretical analyses. The results show that the ratio of the reflected to the incident compression wave at the sudden cross-sectional area reduction increases but the ratio of the passing to the incident compression wave decreases, as the incident compression wave becomes stronger. This experimental results are in good agreements with the previous theoretical ones. The maximum pressure gradient of the compression wave abruptly increases but the width of the wave front does not vary, as it passes over the sudden cross-sectional area reduction.