• Journal of information and communication convergence engineering
• /
• 제7권2호
• /
• pp.215-218
• /
• 2009

In this paper, temperature stable current and voltage references using simple CMOS bias circuit are proposed. To obtain temperature stable characteristics of bias circuit a bandgap reference concept is used in a conventional circuit. The parasitic bipolar transistors or MOS transistors having different threshold voltage are required in a bandgap reference. Thereby the chip area increase or the extra CMOS process is required compared to a standard CMOS process. The proposed reference circuit can be integrated on a single chip by a standard CMOS process without the extra CMOS process. From the simulation results, the reference current variation is less than ${\pm}$0.44% over a temperature range from - $20^{\circ}C$ to $80^{\circ}C$. And the voltage variation is from - 0.02% to 0.1%.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.593-594
• /
• 2008

In this article, process voltage temperature (PVT) compensated on-chip oscillator is implemented by using proportional to absolute temperature (PTAT) circuit and process compensator. Process compensator circuit based on current subtracter and PTAT circuit are proposed for compensation of oscillation frequency to cope with process variation and temperature variation. All circuit can operate in the range of $3.5{\sim}5\;V$ supply voltage. It can be applied to PVT insensitive low frequency clock reference generator.

• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.137-143
• /
• 2002

This paper presents the In-process compensation to control cutter runout and improve the machined surface quality. Cutter runout compensation system consists of the micro-positioning servo system with piezoelectric actuator which is embeded in the sliding table to manipulate radial depth of cut in real-time. Cutting force feedback control was proposed in the angle domain based upon repetitive learning control strategy to eliminate chip load variation in end milling process. Micro-positioning control due to adaptive actuation force response improves the machined surface quality by compensation runout effect induced cutting force variation. This result will provide lots of information to build-up the preciswion machining technology.

• 소성∙가공
• /
• 제14권2호
• /
• pp.147-152
• /
• 2005

The objective of this study is to develop an optimal drawing die for the clad wire drawing process. Cu-clad wire, which has the advantages of the high strength of a steel core and the electro-conductivity, corrosion resistance of a copper layer, is widely being used in the field of the telecommunications, electric-electronic and military technology industries. It is important to obtain uniformly coated rate when producing clad wires. Drawing process of clad wire will be influenced on damage and coated rate of core and sleeve for process variables such as semi-die angle and reduction in area. Therefore, in this study, the finite-element result obtained in this study was analyzed to the effect of the various forming parameters, which included the semi-die angle and reduction in area. The coated rate will be predicted with observation of copper coated rate variation according to total reduction in area and the optimal pass schedule will be set up through proper reduction in area and semi-die angle variation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.237-237
• /
• 2010

We investigated physical properties of CuIn1-xGaxSe2 thin films grown by co-evaporator under various Cu environments. To study the effect of the Cu environments on absorber layer properties, thin films were fabricated under various reaction periods for different Cu flux on 2 stage process. We find the structural and electrical characteristics were affected by the reaction period on 2 stage process. The correlation between Cu flux variation on 2 stage process and solar cell performance was studied. The structural and electrical properties for various Cu flux were discussed.

• Fibers and Polymers
• /
• 제3권2호
• /
• pp.80-84
• /
• 2002

Tension control is an important factor in producing high quality knitted products and in maintaining good processing condition. Yarn tension during knitting is subject to be affected from many elements of the machine and process parameters. Several factors including yam feeding speed, feeding angle, and needle gauge that are considered to influence on the tension variation were investigated. Yam feeding speed did not show high contribution to the tension variation but feeding angle of yam did show high correlation with the tension. No or negative correlation of the tension with needle gauge was found from the results. In order to keep well-determined process condition in the knitting manufacturing, it is strongly suggested that all knitting elements and parameters should be in the integrated control circumstance.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.113-120
• /
• 1994

The dynamic characteristics of turning processes are complex, non-linear and time-varying. Consequently, the conventional techniques based on crisp mathematical model may not guarantee cutting force regulation. This paper presents a fuzzy controller which can regulate cutting force in turning process under varying cutting conditions. The fuzzy control rules are extablished from operator experience and expert knowledge about the process dynamics. Regulation which increases productivity and tool life is achieved by adjusting feedrate according to the variation of cutting conditions. The performance of the proposed controller is evaluated by cutting experiments in the converted conventional lathe. The results of experiments show that the proposed fuzzy controller has a good cutting force regulation capability in spite of the variation of cutting conditions.

• International Journal of Quality Innovation
• /
• 제4권1호
• /
• pp.148-159
• /
• 2003

Variation is the archenemy of quality. To reduce or control the variation in a complex production unit, firstly we need to identify the location of the root cause of the variation. This paper discusses the detection of variability and the techniques used for reduction of variation for a production unit consisting of many processes. In the first part of this paper, the background of variability detection in production systems is introduced which is then followed by a weighted network corresponding to correlation matrix of all processes. Based on the network and clustering criterion of maximum spanning tree, a classification of all processes is derived. Furthermore, the variation of each process in a class is determined by residual analysis. In the last part, the use of methods of robust design for the processes with a larger variability is discussed.

• 한국정보통신학회논문지
• /
• 제10권12호
• /
• pp.2157-2165
• /
• 2006

항등 비트율 서비스를 위한 대표적인 이용자 트래픽 통제 알고리즘인 GCRA에 있어서 네트워크의 과부하와 전송 도중 불가피하게 발생하는 전송지연 변동에 따른 이용자 트래픽의 과도한 손실을 방지하기 위해서는 적절한 전송 지연변동 허용치의 설정이 매우 중요하다. 본 논문에서는 항등 비트율의 소스 트래픽에 대한 GCRA 순응검사에서 지연변동 허용치의 범 위에 따른 GCRA의 성능을 여러 측면에서 분석하고 적절한 지연변동 허용치 설정을 위한 가이드라인을 제시한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1213-1218
• /
• 2007

The brake judder comes from non-uniformities in the tire/wheel assembly caused by mechanical effects such as a brake torque variation (BTV). A disc thickness variation (DTV) related with the kinematic behavior of the disc was investigated a main source of BTV. In this study, a dynamic model with brake corner assembly of full vehicle using MSC.ADAMS was correlated by experiment of judder phenomenon. Judder was generated and correlated systematically by judder experiment in chassis and brake dynamometer from variation in the thickness of the disc. Also it has been found a judder transfer path and variation of the braking pressure. Through analysis of transfer function and movement of subsystem caused by BTV generation, design parameters have been found. Based on the results obtained from parameter study of suspension module, the effective design process and developed model with brake corner assembly was suggested for vibration reduction of steering wheel caused by the judder phenomenon.