• Journal of the Korean Society of Systems Engineering
• /
• v.16 no.2
• /
• pp.110-117
• /
• 2020

In this paper, we estimated the straight line stability by performing a 3 degree of freedom spiral test simulation of a intact/damaged surface combatant using the hydrodynamic coefficient obtained through the PMM(Planar motion mechanism) test based on system engineering process. A model ship was ONR Tumblehome and damaged compartment was set on the starboard bow. As a result of conducting a spiral test simulation based on the experimental results of J.Ha (2018), the asymmetric straight line stability due to the damaged compartment was confirmed. In the case of a ship in which the starboard bow was damaged, it was confirmed that it had the characteristic to deflect to the left when going straight. Also, when estimating the straight line stability of a both port and starboard asymmetric surface combatant, a separated equation of motion model that sees the port and starboard as different ships seems suitable.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.21 no.2
• /
• pp.283-294
• /
• 2023

APro, developed in KAERI for the process-based total system performance assessment (TSPA) of deep geological disposal systems, performs finite element method (FEM)-based multiphysics analysis. In the FEM-based analysis, the mesh element quality influences the numerical solution accuracy, memory requirement, and computation time. Therefore, an appropriate mesh structure should be constructed before the mesh stability analysis to achieve an accurate and efficient process-based TSPA. A generic reference case of DECOVALEX-2023 Task F, which has been proposed for simulating stationary groundwater flow and time-dependent conservative transport of two tracers, was used in this study for mesh stability analysis. The relative differences in tracer concentration varying mesh structures were determined by comparing with the results for the finest mesh structure. For calculation efficiency, the memory requirements and computation time were compared. Based on the mesh stability analysis, an approach based on adaptive mesh refinement was developed to resolve the error in the early stage of the simulation time-period. It was observed that the relative difference in the tracer concentration significantly decreased with high calculation efficiency.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.540-543
• /
• 2006

LTPS TFT backplanes for AM OLED displays have advantages in regard to reliability and performance compared to TFT backplanes based on amorphous silicon. However, the requirements for homogeneous laser crystallization during LTPS process are much higher than for LCD backplanes. Most important is the energy stability of the laser source. In this paper we describe a new excimer laser which meets the requirements of LTPS manufacturing process with high homogeneity.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.5
• /
• pp.773-787
• /
• 2020

In the injection molding process, the controlling stability of products quality is a very important factor in terms of productivity. Even when the optimum process conditions for the desired product quality are applied, uncontrollable external factors such as ambient temperature and humidity cause inevitable changes in the state of the melt resin, mold temperature. etc. Therefore, it is very difficult to maintain prodcut quality. In this study, a system that learns the correlation between process variables and product weight through artificial neural networks and predicts process conditions for the target weight was established. Then, when a disturbance occurs in the injection molding process and fluctuations in the weight of the product occur, the stability control of the product quality was performed by ANN predicting a new process condition for the change of weight. In order to artificially generate disturbance in the injection molding process, controllable factors were selected and changed among factors not learned in the ANN model. Initially, injection molding was performed with a polypropylene having a melt flow index of 10 g/10min, and then the resin was replaced with a polypropylene having a melt floiw index of 33 g/10min to apply disturbance. As a result, when the disturbance occurred, the deviation of the weight was -0.57 g, resulting in an error of -1.37%. Using the control method proposed in the study, through a total of 11 control processes, 41.57 g with an error of 0.00% in the range of 0.5% deviation of the target weight was measured, and the weight was stably maintained with 0.15±0.07% error afterwards.

• Korea-Australia Rheology Journal
• /
• v.17 no.2
• /
• pp.63-69
• /
• 2005

The stability of low-speed spinning process exhibiting spinline flow-induced crystallization (FIC) with no neck-like spinline deformation has been investigated using the method of linear stability analysis. Effects of various process conditions such as fluid viscoelasticity and the spinline cooling on the spinning stability have been found closely related to the development of the spinline crystallinity. It also has been found that the FIC makes the system less stable or more unstable than no FIC cases when the spinline crystallinity reaches its maximum possible value, whereas the FIC generally stabilizes the system if the crystallinity doesn't reach its maximum value on the spinline. It is believed that the destabilizing effect of the FIC on low-speed spinning when the crystallinity is fully developed on the spinline is due to the reduction of the real spinning length available for deformation on the spinline. On the other hand, the increased spinline tension caused by the FIC when the maximum crystallinity is not reached on the spinline and thus no reduction in the spinning length occurs, makes the sensitivity of spinline variables to external disturbances smaller and hence stabilizes the system. These linear stability results are consistent with the findings by nonlinear transient simulation, as first reported by Lee et al. (2005b).

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.4
• /
• pp.445-448
• /
• 2008

The application of the membrane filtration process has been increased for the drinking water treatment system because of excellent quality of treated water compared with the sand filtration process. The selection of suitable pre-treatment processes and optimum flux according to the characteristics of raw water are important factors for the design of membrane processes. In this study, the most efficient pre-treatment processes for drinking water was selected by investigating the effects of pre-treatment processes on the operational stability of the membrane filtration process. Both lab-scale and pilot-scale experiments were conducted. In the lab-scale test, the effect of pre-treatment processes on the stability of the membrane filtration process was investigated indirectly by comparing the performance of membrane flux for raw water, pre-treated water, and membrane permeated water. In the pilot-scale test, the usefulness of prefiltration processes was assessed by comparing the performance of single membrane process and hybrid coagulation-membrane process. The results indicated that the coagulation process contributed to the stabilization of trans-membrane pressure (TMP) by removing contaminants on membranes, though the pre-filtration process had little effect on the TMP.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.50-56
• /
• 2011

Injection molding process is one of the popular manufacturing methods to produce plastic parts with high efficiency and low cost. Ball seat for automobile suspension is made by an injection molding process as a part to support pivot function of ball joint consisted of ball stud and housing. It is necessary for a ball seat to have a dimensional stability in the three dimensional inner area to be contacted with ball stud. In this paper, the dimensional stability of inner surface is indirectly analyzed by checking the difference of inner diameter around the circumferential direction and the thickness variation at the top part of ball seat. Measurement was performed by using the coordinate measuring machine and the fixture to hold ball seat. Optimization of injection molding processes such as injection time, cooling time and temperatures of cylinder barrel was derived to reduce the difference of inner diameter and the thickness variation at the top part of ball seat based on the Taguchi method.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1404-1409
• /
• 2007

Polymers for laser sintering were needed in order to fabricate the articles with the three-dimensional duplication equipment of SLS (selective laser sintering) process. The thermal properties, particle size, distribution, and shape of polymer powder had a close relation with the processibility of laser sintering. In this study, we prepared new polymer powders with uniform size and higher bulk density by wet process. Wet process consists of several finely-controlled steps such as dissolution, nucleation, propagation and crystallization. Several additives were added to improve the thermal, rheological, and flow properties.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.09a
• /
• pp.76-79
• /
• 2004

This research was carried out to evaluate role of supplementary reagents, such as phosphate and SDS, to remove hydrophobic organic contaminant from soils during the EK-Fenton process. The $H_2O$$_2$ stability improved due to the role as stabilizer of phosphate and SDS during the EK-Fenton process. Furthermore, although pH in region near cathode was 8.2 after test, $H_2O$$_2$ stability improved due to transportation of SDS in the region near cathode. Therefore, in tests using phosphate and SDS as supplementary reagent, the efficiency of phenanthrene treatment improved through the EK-Fenton process using longer reaction time.

• Management & Information Systems Review
• /
• v.31 no.1
• /
• pp.183-203
• /
• 2012

This paper investigates how small-medium firms deploy organizational culture, job stability and environmental uncertainty for technological innovation(product and process innovation). This paper suggests that organizational culture has significant effects on technological innovation, that job stability and environmental uncertainty moderate relationship between organizational culture and technological innovation. To test the hypotheses, data were collected from small-medium firms. The survey data of 258 firms were collected and integrated as the empirical base for testing the hypotheses. Major results are as follows: Firstly, when organizational culture as well as control variables are considered, organizational culture had significant and positive effects on product innovation. This result implies that organizational culture is an important means by which small-medium firms can promote innovation. Secondly, the interaction between organizational culture and job stability had a positive and significant effects on product innovation. Thirdly, the interaction between organizational culture and environmental uncertainty had a positive and significant effects on product innovation and process innovation. This paper suggests implications and several future researches need to overcome the limitations of this paper.