• The KIPS Transactions:PartC
• /
• v.13C no.1 s.104
• /
• pp.83-94
• /
• 2006

This paper describes ATM cell encipherment method using Rijndael Algorithm adopted as an AES(Advanced Encryption Standard) by NIST in 2001. ISO 9160 describes the requirement of physical layer data processing in encryption/decryption. For the description of ATM cell encipherment method, we implemented ATM data encipherment equipment which satisfies the requirements of ISO 9160, and verified the encipherment/decipherment processing at ATM STM-1 rate(155.52Mbps). The DES algorithm can process data in the block size of 64 bits and its key length is 64 bits, but the Rijndael algorithm can process data in the block size of 128 bits and the key length of 128, 192, or 256 bits selectively. So it is more flexible in high bit rate data processing and stronger in encription strength than DES. For tile real time encryption of high bit rate data stream. Rijndael algorithm was implemented in FPGA in this experiment. The boundary of serial UNI cell was detected by the CRC method, and in the case of user data cell the payload of 48 octets (384 bits) is converted in parallel and transferred to 3 Rijndael encipherment module in the block size of 128 bits individually. After completion of encryption, the header stored in buffer is attached to the enciphered payload and retransmitted in the format of cell. At the receiving end, the boundary of ceil is detected by the CRC method and the payload type is decided. n the payload type is the user data cell, the payload of the cell is transferred to the 3-Rijndael decryption module in the block sire of 128 bits for decryption of data. And in the case of maintenance cell, the payload is extracted without decryption processing.

• Membrane Journal
• /
• v.22 no.2
• /
• pp.135-141
• /
• 2012

This study was carried out to find the optimum coagulation conditions for ceramic microfiltration process of Y water treatment plant. When pH of raw water from Y Dam was adjusted to 7, the efficiency of coagulation was the best and the optimun dosage of coagulant was 3 mg/L(as $Al_2O_3$) for turbidity of raw water less then 10 NTU in Jar test. In mini module test, the decay rate of specific flux was the lowest when PAC (poly Aluminum Chloride) was used among coagulants and pH was adjusted to 7. The decay rate of specific flux for raw water turbidity of 10~30 NTU was greatly decreased with increase of dosage of coagulant (PAC) while the rate was not significantly decreased for turbidity more than 50 NTU. In conclusion, the optimum dosage of PAC (11% as $Al_2O_3$) was 30 and 50 mg/L for raw water turbidity of less than 10 NTU and more than 50 NTU, respectively. The dosage of PAC should be increased linearly 30 to 50 mg/L depending on raw water turbidity of 10 to 50 NTU.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.48 no.3
• /
• pp.1-10
• /
• 2011

Social network service is defined as an online service or communication service based on social relations among people applied the concept of social network. Social collaborative service included in social network service is characterized by the new value of modified content or recreated content made through collaborative creation process between members of the group. It has the remarkable merits such as sharing and collaboration. But, at the same time, it has the latent problems such as content reuse or copy that is not allowed for members to use. It has been emerged that UCC which is a typical example of recreated or modified content has the copyright issues in both creation and publishing step. To resolve this matter, we don't have many appropriate methods except CCL so far. So, in this paper, we define the problem and implement the UCC metadata manager to control metadata reflecting the feature of UCC. We draw the reference metadata element to identify original content utilized re-creation process. After that we define the R.Metadata Loader module based on the use case. Finally, the proposed UCC metadata manager provides the information of referenced content and lets us to identify the relationship between reference contents. So as to implement prototype, we use Kaltura which is CMS using open source and obtain functional extensibility of metadata manager by using open API.

• Journal of Distribution Science
• /
• v.14 no.2
• /
• pp.65-72
• /
• 2016

Purpose - Recently on-the-job training (OJT) has become the most preferred training and development method with the emergence of the concept that workplace is the best place where learning take place. But many researchers argue that OJT is not helpful for the performance of organization because OJT is not systematic and mostly depend on quality of trainer. Since Jacobs & McGriffin introduced S-OJT (structured OJT), there has been plenty of researches. But most of the researches have focused mainly on employee's attitude and organizational performance caused by S-OJT and neglected a holistic approach of S-OJT as a system. S-OJT need to be analyzed comprehensively to understand training performance because S-OJT is operated as a system consist of input, process, and organizational context. Although S-OJT may create unintended consequences, there were few researches to explore them. Thus, the purpose of this study is to identify the critical success factors for S-OJT and to find unintended consequences of it. Research design, data and methodology - We conducted a case study on M business unit of A company which developed and has been implementing S-OJT program for years. We designed and prepared the process, collected and analyzed data for the study. We set the theoretical framework to analyze the case after reviewing theories and previous studies on S-OJT. We collected and analyzed internal reports and interview results of the employees of the M business unit. We tried to collect as many information as possible to secure the validity of the research results. Results - The critical success factors identified in the study are as follow. First, it is important to select and train proper trainers for S-OJT. Second, it is needed to develop structured training module. Third, organization have to use effective communication system like on-line community. Forth, trainer should have proper skills for training such as facilitating skill, coaching skill, and delivering skill etc. Fifth, proper learning place is needed. Sixth, organizational support is important especially, immediate supervisor support and concern is critical. Eleventh, it is needed to consider situational contexts. Among them, overload to the trainer will affect the effectiveness of S-OJT. In this study, we found an additional unintended consequence. "To teach is the best way to learn." Experience as a trainer give employee an opportunity to organize one's knowledge and skill and to attain facilitation skill, coaching skill, and relation skill. Thus, organization may use S-OJT to train the potential talent. Conclusions - Many organizations introduced S-OJT to train the newcomers because S-OJT drew attention as an important tool to develop employees. Following this trend, there has been increasing number of researches to find the results of S-OJT and identify the determinants of S-OJT success. However, most of the researches concentrated on finding effects of some factors neglecting holistic approach. This study tried to identify critical success factors affecting effectiveness of S-OJT by using case study and find additional unintended consequence. The results of the study will be useful for organizations which have a plan to adopt S-OJT.

• Membrane Journal
• /
• v.24 no.2
• /
• pp.123-135
• /
• 2014

The effects of pH, saturated oxygen, and back-flushing media were investigated in hybrid process of tubular ceramic microfiltration and $TiO_2$ photocatalyst-loaded PES (polyethersulfone) beads for advanced drinking water treatment, and compared results of water, nitrogen, or oxygen back-flushing in the viewpoints of membrane fouling resistance ($R_f$), permeate flux (J) and total treated water ($V_T$). $R_f$ decreased, and J and $V_T$ increased as decreasing pH. Turbidity treatment efficiencies were similar at water or nitrogen back-flushing independent of pH, but DOM (dissolved organic matter) treatment efficiency did not have a trend at water back-flushing. $R_f$ at NBF (no back-flushing) with SO (saturated oxygen) was the lower than that at NBF without SO. Also, the DOM treatment efficiency at NBF with SO was the lower than that at NBF without SO. It happened because OH radicals produced by reaction of SO and photocatalyst could dilute with water inside the module. The DOM treatment efficiency of gas back-flushing showed the larger than that of water back-flushing at back-flushig period 10 min. It proved that the adsorption or photo-oxidation of PES beads could be activated by the more effective bead-cleaning of gas back-flushing than water back-flushing.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.2
• /
• pp.156-160
• /
• 1997

The combination of biological wastewater treatment process and membrane separation has many advantages such as better effluent quality and system stability over the conventional biological wastewater treatment process. In this study, direct membrane separation using nonwoven fabric was applied to biological wastewater treatment. A nonwoven fabric module was submerged in the aerated bioreactor. And accumulated biomass in the bioreactor was separated by suction. The system was operated with various condition to investigate pollutant removal efficiencies and flux. After formation of biomass layer on nonwoven fabric surface, a day, the stable effluent water quality was obtained. The flux decreased at a high suction pressure faster than a low pressure. The stable flux was obtained at the pressure of $21{\sim}25cmHg$. In spite of variation of hydraulic retention time, organic loading rate, the removal efficiencies of BOD, $COD_{Cr}$. $COD_{Mn}$ were very high as follows : $95.2%(0.14{\sim}0.97\;BODKg/m^3/day)$, $86.0%(0.17{\sim}1.39\;COD_{Cr}Kg/m^3/day)$, $90.0%(0.097{\sim}0.61\;COD_{Mn}Kg/m^3/day)$.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.669-678
• /
• 1994

The BOD removal characteristics of submerged biofilters filled with three kinds of filter media respectively were experimentally examined with constant temperature, pH value and variable BOD loading and recirculation ratio. Obtained results are as follows; 1. The BOD removal ratio decreases with the increasing $BOD_5$ volumetric loading rate, and the loading rate for the BOD removal over 90% is lower thean $1.6kg{\cdot}BOD_5/m^3{\cdot}d$ for the plastic media of Netring and cubic wire meshes. This is a much large value than $0.3{\sim}0.8kg{\cdot}BOD_5/m^3{\cdot}d$ for conventional activated sludge process. The required submerged biofilter volume is found to be much samller than that of conventional activated sludge process. 2. The decreasing order of BOD removal is Netring (random plastic media), cubic wire meshes (plastic module), and then gravel (stone media). This is mainly due to the media characteristics such as void ratio, specific surface area and media shapes. 3. The $BOD_5$ removal rate increases with the recircuration ration, but the rate of increases becomes samaller as the recirculation ratio increases over 20. When $BOD_5$ loading is $1.8kg{\cdot}BOD_5/m^3{\cdot}d$, the required recirculation rationto obtain 90% $BOD_5$ removal is about 20 for Netring and it was about 30 for cubic wire meshes. 4. Reynold's Number increases with recirculation ratio, and the Reynold's Numbers corresponding to the recircuration ratio of 10~50 are less than 52, showing laminar up flows in the filter. The settled and effluent sludges increase with increase of Reynol's Number, and there are the definite Reynold's Numbers at which the settling sludge concentrations become nearly constant respectively in each filters. 5. In this submerged biofilter system, small volume of sludge hopper can be substituted for a separated settling tank.

• Journal of KIISE:Computer Systems and Theory
• /
• v.27 no.5
• /
• pp.485-495
• /
• 2000

The parallel computer system that uses parallel program on the application such as a large scale business or complex operation is required. One of crucial operation of parallel computer system is synchronization. A representative method of synchronization is barrier synchronization. A barrier forces all process to wait until all the process reach the barrier and then releases all of the processes. There are software schemes, hardware scheme, or combinations of these mechanism to achieve barrier synchronization which tends to use hardware scheme. Besides, barrier synchronization lets parallel computer system fast because it has fewer start-up overhead. In this paper, we propose a new switch module that can implement fast and fault-tolerant barrier synchronization in hardware scheme. A proposed barrier synchronization is operated not in full-switch-driven method but in processor-driven method. An effective barrier synchronization is executed with inexpensive hardware supports. Therefore, a new proposed hardware barrier synchronization is designed that it is operated in arbitrary network topology. In this paper, we only show comparison of barrier synchronization on Multistage Interconnection Network. This research results in 24.6-24.8% reduced average delay. Through this result, we can expect lower average delay in irregular network.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.2
• /
• pp.873-876
• /
• 2016

Background: Studies of quality of life (QoL) of oncological patients is carried out using questionnaires approved in many international clinical studies. The European Organization for Research and Treatment of Cancer EORTC QLQ-C30 (Quality of Life Questionnary-Core 30) and its special brain cancer module EORTC QLQ-BN20 are widely used in the world neurooncologic practice. They are available in more than 80 official versions of 30 languages of the world. Previously we used the official versions in Russian, which often causes difficulty in understanding for native Kazakh language speakers, who comprise more than 60% of our respondents. This was the reason for creating a version of Kazakh language. Therefore, in 2014 for the first time the process of adaptation of questionnaires to the Kazakh language was initiated. Materials and Methods: The translation process of questionnaires to Kazakh language was held in accordance with the requirements of the European Organization for Research and Treatment of Cancer EORTC on QoL and consisted of the following stages: preparation - translation - pilot testing - approval. The official permission of authors and "Guideline on translation" was obtained which was developed by the working group of the EORTC on QoL. The pilot testing of EORTC QLQ-C30 and QLQ-BN20 questionnaires was conducted on the basis of the Department of Central Nervous System Pathology of the "National Centre for Neurosurgery" in patients with malignant tumors of the central nervous system. Results: The official versions of the EORTC QLQ-C30 and QLQ-BN20 questionnaires in Kazakh language were introduced and adapted in practical neurosurgical operations in Kazakhstan. Conclusions: The approved versions of the questionnaires in Kazakh language are now available for mainstream use on the official website EORTC.com. The versions of these questionnaires can be used in domestic cohort studies and clinical practice in the Republic of Kazakhstan. The use of these tools for assessing QoL will help professionals in the planning of individual treatment strategies and selection of the necessary therapy.

• Journal of architectural history
• /
• v.12 no.1 s.33
• /
• pp.25-41
• /
• 2003

This paper is a study of Le Corbusier's trace regulateur of the 1920s, particularly its role in the design of the Villas La Roche-Jeanneret and Stein-de Monzie. It proceeds on the basis of the following three themes: first, the relation between the regulating line and the dom-ino frame; second, its status as a proportional device based not on a module system but one that defines relations; third, its function as an essential practical device in the design process. In the Villa La Roche-Jeanneret, the embedded horizontal planes of the dom-ino frame were constant, but the vortical lines of the columns were altered according to the changes in plan. Initially, a left-hand bay window formed a symmetry with the right-hand bay window, the only constant in the design process. With subsequent changes, mullion sections of the horizontal window and roof elements came to provide the reference points for the regulating line. Eventually, a regulating line different from the one that controlled the bay window and the elongated volume came to control the entrance hall of Villa La Roche, resulting in three different kinds of regulating lines in the final version. In contrast to the Villa La Roche-Jeanneret, a singular and consistent regulation line was anticipated in the earliest design stages of the Villa Stein-de Monzie. The repetition of its A:B grid and the standard $2.5m{\times}1.0m$ sliding window determined the proportions of both its plan and elevation, and thus the regulating line became 'automatic,' losing its viability as a practical tool. Though the regulating titles of the La Roche-Jeanneret look as if they were an afterthought, drawn after the design was complete, they were most active, requiring tenacity and discipline in their application. On the other hand, the seemingly 'redundant' regulating line of the Villa Stein-de Monzie gains its raison d'etre from the dom-ino frame. Its cantilevers and uninterrupted horizontal window could be used in decisive fashion because of the guarantee that the correct proportion would always be maintained. Thus we discover that Le Corbusier's discipline of the 1920s had a certain spectrum of flexibility. His 'parti' ranged from the extremely loose and malleable grid of the Villa La Roche-Jeanneret to the fixed grid of the Villa Stein-de Monzie. In different ways, these projects retain the tension between the dom-ino frame and the regulating line. For Le Corbusier, as much as the grid was an object with fixed attributes, it was also an active medium manipulated by the will of the architect.