• International Journal of Safety
• /
• v.6 no.2
• /
• pp.1-7
• /
• 2007

In this study mechanical strength of A53B carbon steel was analyzed using several types of test specimens directly machined from oil recycling pipe experienced a failure due to hydrogen attack in chemical plants. High temperature hydrogen attack (HTHA) is the damage process of grain boundary facets due to a chemical reaction of carbides with hydrogen, thus forming cavities with high pressure methane gas. Driven by the methane gas pressure, the cavities grow on grain boundaries forming intergranular micro cracks. Microscopic optical examination, tensile test, Charpy impact test, hardness measurement, and small punch (SP) test were performed. Carbon content of the hydrogen attacked specimens was dramatically reduced compared with that of standard specification of A53B. Traces of decarburization and micro-cracks were observed by optical and scanning electron microscopy. Charpy impact energy in hydrogen attacked part of the pipe exhibited very low values due to the decarburization and micro fissure formation by HTHA, on the other hand, data tested from the sound part of the pipe showed high and scattered impact energy. Maximum reaction forces and ductility in SP test were decreased at hydrogen attacked part of the pipe compared with sound part of the pipe. Finite element analyses for SP test were performed to estimate tensile properties for untested part of the pipe in tensile test. And fracture toughness was calculated using an equivalent strain concept with SP test and finite element analysis results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.6
• /
• pp.95-99
• /
• 2013

Furnace is currently the most important doping process using POCl3 in solar cell. However furnace need an expensive equipment cost and it has to purge a poisonous gas. Moreover, furnace typically difficult appling for selective emitters. In this study, we developed a new atmospheric pressure plasma source, in this procedure, we research the atmospheric pressure plasma doping that dopant is phosphoric acid($H_3PO_4$). Metal tube injected Ar gas was inputted 5 kV of a low frequency(scores of kHz) induced inverter, so plasma discharged at metal tube. We used the P type silicon wafer of solar cell. We regulated phosphoric acid($H_3PO_4$) concentration on 10% and plasma treatment time is 90 s, 150 s, we experiment that plasma current is 70 mA. We check the doping depth that 287 nm at 90 s and 621 nm at 150 s. We analysis and measurement the doping profile by using SIMS(Secondary Ion Mass Spectroscopy). We calculate and grasp the sheet resistance using conventional sheet resistance formula, so there are 240 Ohm/sq at 90 s and 212 Ohm/sq at 150 s. We analysis oxygen and nitrogen profile of concentration compared with furnace to check the doped defect of atmosphere.

• The Journal of the Korea Contents Association
• /
• v.11 no.12
• /
• pp.182-189
• /
• 2011

This study was conducted to evaluate the usability of augmented reality (AR) picture book for young children. The participants of this study were 17 five-year-olds attending to M kindergarten in Korea. The measurement of the usability was conducted by observation and interviews during and after children's AR picture book reading 1) usability test score such as task completed that is, reading the AR picturebook successfully, 2) children's behaviors in the process of reading the book, 3) children's response to the questions asking the level of satisfaction with the AR picture book. The result of study showed that most of children could read the AR successfully adjusting the distance and angle of AR picture book to web-camera's location. And children showed verbal and nonverbal expression such as surprise, joy, questions and frustration in reading the book. Children told that AR picture book is fun and easy to read. This study would provide the implications for the interface development and adult-child book reading of AR picture books.

• Ocean and Polar Research
• /
• v.39 no.4
• /
• pp.257-267
• /
• 2017

Although Pacific mackerel (Scomber japonicus) is an important commercial species in Korea, its recruitment mechanism remains largely unknown. Diel vertical positioning of larvae in the water column, which is affected by their specific gravity and the surrounding water density, may help to provide an understanding on recruitment success through predator avoidance and prey availability. The specific gravity measurement on Pacific mackerel eggs and larvae would seem to be essential information necessary to learn about the transport process from spawning to nursery grounds, and consequently the recruitment success. Eggs were artificially fertilized, and larvae were fed with rotifer when their mouths opened 3-4 days after hatching. We conducted the experiment using a density gradient water column to measure the ontogenetic changes in specific gravity from fertilization to 10 days after hatching. Egg specific gravity was stable during most of the embryonic period, but a sudden increase to $1.0249g\;cm^{-3}$ happened just before hatching. However, the specific gravity of newly hatched larvae was much lighter ($1.0195g\;cm^{-3}$), and specific gravity tended to increase continuously after hatching. Comparison of specific gravity with seawater density reveals that eggs and newly hatched larvae can float in the surface layer of the ocean. For the later period of the experiment, the specific gravity showed a cyclic diel pattern: the highest in the evening while the lowest at dawn. The fullness of larval stomach may be responsible for the observed differences in specific gravity, because stomach fullness was lower (40-60%) at midnight, and higher (80-85%) in evening. The diel pattern of specific gravity might provide clues regarding how larvae match the diel vertical migration of prey organisms.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.4
• /
• pp.437-451
• /
• 2012

Application of 3D laser scanner to civil engineering is widely studied in various fields such as tunnel, bridge, calculation of earth volume, construction measurement, observation of rock joint, etc. Some studies on utilization of the 3D laser scanner for calculating the over-break and/or under-break of tunnels have also been carried out. However, in the previous research, the scanning data were usually compared with the 2D CAD blueprint results; although the shape of tunnel structure is relatively simple, for precise calculation of the over-break and/or under-break of tunnels, three-dimensional analysis based on BIM is needed. Therefore, in this paper, a new program that calculates the over-break and/or under-break of tunnels using the 3D laser scanner and the BIM is developed; moreover the effective and rapid process of data treatment is proposed. The accuracy of the developed program was verified by applying the new system to a real tunnels construction field.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.5
• /
• pp.405-412
• /
• 2015

This paper represents a filter design to estimate the airspeed of a spin-stabilized, trajectory-correctible artillery ammunition. Due to the limited power and space in operational point of view, the airspeed sensor is not installed, and thus the airspeed need to be estimated using limited sensor measurements. The only IMU measurements(three-axis specific forces and angular rates) are used in this application. The extended Kalman filter algorithm is applied since a linear filter can not cover the its wide operational range in airspeed and altitude. In the implementation of the EKF, the state and measurement equations are transformed into the no-roll frame for simple form of Jacobian matrix. The simulation study is conducted to evaluate the performance of the filter under various environment conditions of sensor noise and wind turbulence. In addition, the effect of the choice in filter design parameters, i.e. process error covariance matrices is analyzed on the performance of the estimation of airspeed and angular rates.

• Journal of Broadcast Engineering
• /
• v.14 no.3
• /
• pp.366-377
• /
• 2009

In this paper, we implement the real-time system which extracts 3-dimensional coordinates from right and left images captured by a stereo camera and provides users with reality through a virtual space operated by the 3-dimensional coordinates. In general, all pixels in correspondence region are compared for the disparity estimation. However, for a real time process, the central coordinates of the correspondence region are only used in the proposed algorithm. In the implemented system, 3D coordinates are obtained by using the depth information derived from the estimated disparity and we set user's hand as a region of interest(ROI). After user's hand is detected as the ROI, the system keeps tracking a hand's movement and generates a virtual space that is controled by the hand. Experimental results show that the implemented system could estimate the disparity in real -time and gave the mean-error less than 0.68cm within a range of distance, 1.5m. Also It had more than 90% accuracy in the hand recognition.

• The Journal of the Korea Contents Association
• /
• v.2 no.2
• /
• pp.53-63
• /
• 2002

As the microelectronics technology is developed, new types d smart intelligent produce are being emerged. OSD user interface is one of the critical factor in this kind of product, especially brown goods and information devices, as it is responsible for input and output function. OSD is being treated as accompaniment to hardware in spite of its importance, and therefore is developed from only simple and separate usability testing based on performance measurement. This study propose a usability evaluation method of OSD based on subjective preference to support existing usability testing. The purpose of this analysis is to make dear what is important factor and how its preference level is from the user's viewpoint. The various attributes of OSD are clarified from user's questionaire and interview, and orthogonal array is generated with specifed factor levels. The prototypes are generated from rapid prototyping tool and tested in natural simulation environment. The preference data which collected in this usability testing is analyzed with conjoint analysis module. This usability evaluation is not the final stage in user interface design process but the early famed and circulated stage.

• The Journal of the Korea Contents Association
• /
• v.7 no.9
• /
• pp.156-166
• /
• 2007

Traditional financial approaches have been failed to satisfy the firms in evaluating the payoffs from information technology(IT) investment. This research developed a processed-oriented model to evaluate the impacts of IT on the primary business activities within the value chain. The model proposed in this research incorporates corporate goals for IT and strategic alignment as key measurements of IT impacts. We found that corporate goals for IT can be classified into one of four categories: unfocused, operations focus, market focus, and dual focus(operations and market focus), using survey data collected from 137 corporate executives in Korea. The empirical analysis confirms that corporate goals for IT are useful indicators of impacts from IT in that executives in firms with more focused goals for IT perceive higher payoffs from IT in the value chain. We also found that strategic alignment contributes to higher perceived levels of IT payoffs.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.48-48
• /
• 2003

A precision orbit determination (POD) system of low Earth orbiter using the GPS dual frequency measurements has been developed. It is an option of KOMPSAT-2 POD process system. In this research, the orbit determination using the real dual frequency carrier phase measurements of the SAC-C satellite was conducted to verify KOMPSAT-2 POD system reliability. The SAC-C satellite is an international cooperative mission between NASA, the Argentine Commission on Space Activities (CONAE), Centre National d'Etudes Spatiales (CNES or the French Space Agency), Instituto Nacional De Pesquisas Espaciais (Brazilian Space Agency), Danish Space Research Institute, and Agenzia Spaziale Italiana (Italian Space Agency). The SAC-C was launched at November 21, 2000. The altitude of SAC-C is 702 km and it carries a TurboRogue III GPS and four high gain antennas developed by the JPL. The receiver is able to generate the dual frequency code and carrier phase data. Double-differenced carrier phase measurements were formed using 25 IGS stations. The data were sampled at 30 seconds interval. Fully dynamic approach was adopted for POD. The POD results were compared with those of JPL using GOA n software. The comparison verifies that deci-meter level 3D position accuracy of low Earth orbiting satellite could be achieved. The POD system has been developed successfully.