• Journal of the Korean Applied Science and Technology
• /
• v.15 no.3
• /
• pp.55-60
• /
• 1998

The sodium ${\alpha}-sulfo$ fatty acid vinyl ester oligomers, which are oligomer type surfactants were prepared by polymerization with fatty acid vinyl acetate. The ${\alpha}-sulfonation$ of fatty acid vinyl ester oligomers were carried by direct addition of sulfur trioxide. The dispersing performance of oligomer type anionic surfactants and sodium dodecyl sulfate(SDS) in the aqueous suspension of iron oxide and titanium dioxide particles was evaluated by particle size distribution and zeta-potential measurement. As results, the particles of iron oxide and titanium dioxide were flocculated by addition of small amount of oligomer type anionic surfactants and sodium dodecyl sulfate(SDS), then the flocks redispersed by more addition of oligomer type anionic surfactants and SDS. The flocculation, redispersion process was observed in lower concentration range of oligomer type anionic surfactants than SDS. Especially, the dispersing action of sodium ${\alpha}-sulfo$ palmitic acid vinyl ester oligomer was better than sodium ${\alpha}-sulfo$ lauric acid vinyl ester oligomer.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.4
• /
• pp.11-15
• /
• 2007

As preparing electrode for the OLED with the sputtering process, in order to be lower damage of the bottom organic layer and increase the life-time of the OLED, we prepared Al electrode for that by using Facing Targets Sputtering (FTS) system. Al electrode directly deposited on the cell (LiF/EML/HTL/Bottom electrode). Deposition condition was the working gas (Ar, Kr and Ar+Kr) and working gas pressure (1 and 6 mTorr). The film thickness and I-V curve of Al/cell were evaluated by a $\acute{a}$-step profiler and a semiconductor parameter (HP4156A) measurement. The thin film surface image was observed by a Atomic Force Microscope (AFM). In result, in comparison with about 11 [V] of the turn-on voltage of Al/cell with using the pure Ar gas, when Al thin film was deposited using the Ar-Kr mixture gas, the surface morphology was improved in some region and the turn-on voltage of Al/cell could be decreased to about 7 [V].

• Journal of Welding and Joining
• /
• v.24 no.6
• /
• pp.13-20
• /
• 2006

Resistance spot welding is widely used for joining sheet metals in the automotive manufacturing process. Recently, servo-gun is used to increase the productivity and precise control the acting force. However, force control mechanisms have not been investigated with servo-guns until now. In this paper, it is proved that servo-motor current is proportional to torque and by experiment, experimental equation between servo-motor current and electrode force was derived. Algorithm for feedback control of electrode force was suggested using current measurement. In addition, applying soft touch method to this system the impact between electrode and specimen, which is the problem of air gun, could be reduced. Indentation made the force decrease in holding time of resistance spot welding. In order to overcome this problem, force compensation using the servo gun was used and it improved weld strength in good welding current range.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.361-367
• /
• 2001

Recently, Chemical Mechanical Polishing(CMP) has become a leading planarization technique as a method for silicon wafer planarization that can meet the more stringent lithographic requirement of planarity for the future submicron device manufacturing. The SOI(Silicon On Insulator) wafer has received considerable attention as bulk-alternative wafer to improve the performance of semiconductor devices. In this paper, the objective of study is to investigate Material Removal Rate(MRR) and surface micro-roughness effects of slurry and pad in the CMP process. When particle size of slurry is increased, Material Removal rate increase. Surface micro-roughness is greater influenced by pad than by particle size of slurry. As a result of AM measurement, surface micro-roughness was improved from 27 $\AA$ Rms to 0.64 $\AA$Rms.

• Journal of ILASS-Korea
• /
• v.1 no.1
• /
• pp.63-75
• /
• 1996

The purpose of this study is to investigate the break-up characteristics by taking advantage of a two-phase coaxial nozzle. Air and water are utilized as working fluids and the mass ratio air/water has been controlled to characterize the atomization, diffusion and development of mixing process. By way of a photographic technique, conventional developing structures and diffusion angles have been analyzed systematically with variations of mass ratios. The turbulent flow components of the atomized particles were measured by a two channel LDV system and the data were treated by an on-lined measurement equipment. According to the photographic results the spreading angles decreased because the axial inertia moment was relatively higher than the lateral one with respect to the increase of mass ratio. It is found the jet flow diffuses linearly in a certain limit region while the atomizing characteristics, in terms of the distributions of particle diameters did not show particular differences. It may be expected that these fundamental results can be used as reference data in studying the atomization, breakup and diffusions.

• Journal of the Korean Ceramic Society
• /
• v.31 no.3
• /
• pp.265-274
• /
• 1994

Intermetallic Ti-Si system ceramics were synthesized from stochiometric mixtures of titanium and silicone powders in vacuum by Self-propagating High-temperature Synthesis(SHS). In each cases of Ti5Si3, Ti5Si4 and TiSi, and TiSi2 synthesis, 20wt% product dilution, direct ignition and SHS chemical furnace method were employed. The combustion modes, which were observed during the synthesis process by using the high speed camera, of Ti5Si3, Ti5Si4, TiSi, and TiSi2 exhibit spin, osciallatory, steady-state, and spin combustion, respectively. With increasing Ti/Si molar ratio an decrease of combustion velocities was found. From the results on the measurement of the flexural strength, the specimen hot pressed at 135$0^{\circ}C$ for 30 min using synthesized Ti5Si4 powders showed the highest flexural strength at 215 MPa.

• Journal of Surface Science and Engineering
• /
• v.38 no.1
• /
• pp.44-48
• /
• 2005

We prepared nickel silicide layers from p-Si(l00)/SiO₂(2000 Å)/poly-Si(700 Å)/Ni(400 Å) structures, feasible for gates in MOSFETs, by annealing them from 500℃～900℃ for 30 minutes. We measured the color coordination in visible range, cross sectional micro-structure, and surface topology with annealing temperature by an UV-VIS-IR spectrometer, field effect scanning electron microscope(FE-SEM), and scanning probe micro-scope respectively. We conclude that we may identify the nickel silicide by color difference of 0.90 and predict the silicide process reliability by color coordination measurement. The nickel silicide layers showed similar thickness while the columnar grains size and surface roughness increased as annealing temperature increased.

• Journal of Information Technology Applications and Management
• /
• v.11 no.4
• /
• pp.181-208
• /
• 2004

By the developing of Internet. the environments of the company have rapidly been changed. Especially. managers in the Internet shoppingmall have been try to provide excellent e-Services to their customers. e-Service i~ defined comprised of all interactive services that are delivered on the Internet uSing advanced telecommunications. information, and multimedia technologies. but according to study of e-Satisfy. com［2000］. customer service through internet is still neither effective nor efficient and poor service will impact on company's profit but excellent service can improve their value and quality of the service or product. In order to customer-oriented e-Services. this study suggested the QFD linked with e-Service quality model for the Internet shoppingmall service system. which can help determine design characteristics being relevant to customer's e-Service quality requirements. this hybrid model have two stages. In the first stage. we do measure service quality and find priorities of service quality attribute by purchase process. and in the second stage. on the basis of priority of e-Service quality attributes, we find design characteristics to maximize customer satisfaction. From this study, we provide internet shoppingmall managers with the implications for improvement of service quality, measuring quality of e-service, providing design characteristics for customer-oriented service quality.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.3 no.1
• /
• pp.41-56
• /
• 1999

Since UV-B radiation measuring networks have not been established, numerical models which calculate the flux from other readily available meteorological measurements may play an important role. That is, such a problem can be solved by using parameterization models such as two stream approximation, the delta-Eddington method, doubling method, and discrete ordinate method. However, most UV-B radiative transfer models have not been validated with measurements, because such models are not intended as practical computational schemes for providing surface estimates of UV-B radiation. The main concern so far has been to demonstrate model sensitivity for cloudless skies. In particular, few have been concerned with real cloud information. Clouds and aerosols have generally been incorporated as constituents of particular atmospheric layers with specified optical depths and scattering properties. The parameterization model presented here is a combination of a detailed radiative transfer algorithm for a coludless sky radiative process and a more approximate scheme to handle cloud effects. The model input data requires a daily measurement of the total ozone amount plus a daily record of the amount and type of cloud in the atmosphere. Measurements for an examination of the models at the Department of Atmospheric Sciences, Pusan National University have been takenfrom February, 1995. These models can be used to calculate present and future fluxes where measurements have not been taken, and construct climatologies for the period before ozone depletion began.

• Journal of Korean Academy of Nursing
• /
• v.43 no.5
• /
• pp.587-594
• /
• 2013

Purpose: The purpose of this study is to provide researchers with a simplified approach to undertaking exploratory factor analysis for the assessment of construct validity. Methods: All articles published in 2010, 2011, and 2012 in Journal of Korean Academy of Nursing were reviewed and other relevant books and articles were chosen for the review. Results: In this paper, the following were discussed: preliminary analysis process of exploratory factor analysis to examine the sample size, distribution of measured variables, correlation coefficient, and results of KMO measure and Bartlett's test of sphericity. In addition, other areas to be considered in using factor analysis are discussed, including determination of the number of factors, the choice of rotation method or extraction method of the factor structure, and the interpretation of the factor loadings and explained variance. Conclusion: Content validity is the degree to which elements of an assessment instrument are relevant to and representative of the targeted construct for a particular assessment purpose. This measurement is difficult and challenging and takes a lot of time. Factor analysis is considered one of the strongest approaches to establishing construct validity and is the most commonly used method for establishing construct validity measured by an instrument.