• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.1
• /
• pp.35-44
• /
• 2015

Thermomechanical pulping process uses large amounts of energy, mostly electricity to run electrical facilities. Thermomechanical pulp (TMP) made from Pinus densiflora also has a big drawback that refining consumes 90 per cent of the total energy used in TMP process. This study explored to draw up a way to save refining energy through different thermal treatment at the stages of presteaming and refining. Presteaming temperature was $80^{\circ}C$, $100^{\circ}C$, and $120^{\circ}C$. After presteaming at each temperature, refining was carried out at $100^{\circ}C$, $120^{\circ}C$, and $140^{\circ}C$ respectively. In a presteaming stage, steaming temperature over $120^{\circ}C$ greatly contributed to the decrease of refining energy leading to earlier attainment of a target freeness, irrespective of refining temperature. In addition, NaOH treatment with presteaming enhanced better development of fiber properties during refining than presteaming without NaOH. High temperature refining at $140^{\circ}C$ produced a high strength paper, and wood chips treated by alkali responded better to refining than at over $120^{\circ}C$. Improved softening effect on wood chips led to the decrease in shives contents but it gave no effect on pitch contents of TMP.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.2
• /
• pp.73-80
• /
• 1992

The effect of presteaming on native oak specimens(Quercus serrata) of 2.5cm thick were investigated by measuring specific gravities, internal moisture gradients, residual extractives, and transport rates of free and bound water. The specific gravities and internal moisture gradients of the presteamed samples did not much deviate from those of the controls, but after presteaming discrepancy in moisture content between specimens lessened. The amount of residual hot-water extractives of the presteamed samples were less than those of the controls by 25%. The transport rates of bound water were determined by measuring steady-state diffusion coefficients with a vapormeter cup. After presteaming the diffusion coefficients in radial direction increased by 35%, but decreased those in the tangential direction.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.15-22
• /
• 1997

The effectiveness of presteaming for improving CCA treatability on refractory Japanese larch heartwood was investigated in this study. Presteaming was effective on improving treatability, and the extent of improvement was dependent on moisture contents of wood specimen and steaming conditions. Green wood showed higher average value in both preservative retention and penetration than dry wood, and steaming under pressure conditions also had higher treatability than steaming at atmospheric conditions. The degree of improvement for treatability was increased with the extension of steaming period. Treatability of dry wood pres teamed under pressure conditions more than 6 hours and green wood for 3 hours was similar to that enhanced by conventional incising. Presteaming green wood under pressure conditions more than 6 hours was more effective than conventional incising in improvement of CCA treatability, and resultant treatability satisfied a minimum value required for CCA-treated wood for being used at the regions of hazard class H3 and H4. In addition, an improvement of treatability by presteaming was due to an increase in permeability resulted from the degradation of hemicelluloses within aspirated pit membrane and cell wall, not the removal of extractives from pit membrane. The reduction in strength, measured as longitudinal compressive strength, due to pres teaming was related with the degradation of hemicelluloses, and was increased as steaming conditions were severe. The degree of strength reduction associated with presteaming treatment to obtain required treatability could be quantified from the relatively good relation between the increase in treatability and the decrease in strength.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.1
• /
• pp.66-71
• /
• 1994

To increase drying rate and reduce drying degradation, pretreatments such as prefreezing and presteaming have been widely used in wood industries. Presteaming lumbers prior to kiln drying is known positively to improve its permeability, to increase diffusion coefficient and to reduce discoloration, but negatively to increase collapse. Prefreezing lumbers prior to kiln drying is also known to reduce significantly its drying defects and its shrinkages. Thus it is no doubt that the pretreated lumbers shrink diversely from the untreated. In this study the shrinkage behaviors of the pretreated specimens are investigated by drying two tropical hardwoods (Apitong and Taun) in three different dying conditions: high temperature and slow drying rate (drying in a closed cylinder), high temperature and rapid drying rate (drying in an oven) and low temperature and slow drying rate(drying at room temperature). The prefrozen specimens show the least volumetric shrinkages in most drying conditions. The specimens dried in cylinders shrink most among all drying conditions. In general the pretreated specimens reached the 30 % moisture content faster than the untreated by about 30 %.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.2
• /
• pp.3-13
• /
• 1985

This study was carried out to investigate the effects of presteaming on the drying rate and drying defects of 3 cm - thick Quercus acutissima. Specimens for presteaming were steamed green at $100^{\circ}C$ for 4 hours and then kiln-dried to 10 percent moisture, content with controls, using the kiln-drying schedule ($T_4-C_2$) recommended by Rasmussen. The results obtained were as follows: 1. Presteaming reduced drying time approximately 18 percent from 70 to 10 percent moisture content. 2. The effect of presteaming on surface checking was not significant. 3. Presteamed specimens showed the reduction in end checking compared with controls. 4. Percents of boards with collapse, cupping, and honeycomb of presteamed specimens were slightly lower than those of controls. 5. Dry lumber grade of presteamed specimens was better than that of controls. Percent of first grade boards of presteamed specimens was 20 percent higher than that of controls and percents of second and third grade boards of presteamed specimens were 15 and 5 percent lower than those of controls, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.1
• /
• pp.35-41
• /
• 1995

Persimmon boards of 30mm thick were dried, their temperatures were monitored during drying with 490 and 200watt microwave, and the drying efficacy and problems were investigated. The effects of pretreatments such as presteaming and prefreezing were also examined. The persimmon green lumbers of 80% moisture content were dried to 10% for only 50~60 and 110 minutes with 49watt and 200watt microwave, respectively. Severe internal checks were, however, found in all boards. The presteamed boards collapsed on their surfaces earlier than the controls. It may attribute to the high temperature inside boards during microwave drying and the decrease of their internal tensile strength caused by the presteaming treatment. To increase the internal tensile strength of the pretreated boards and to reduce their internal checks, they were air-dried at room temperature. The air-dried boards could be dried to 10% moisture content clearly and free from defects with 200watt microwave. The heating efficiency were also calculated with the maximum weight loss per minute of 490watt and 200watt.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.4
• /
• pp.141-148
• /
• 1996

The pulished works on Accelerated Curing Effect were generally performed around from 1960 to 1970th century for 18 to 24 hours - total curing periods. It is not possible to define the effect of temperature rise because those results were obtaine mainly by using the manually operated steam-curing tank. Thus, it may not be available to apply those data immediately on the domestic PC wall production line. The testing specimens were made from the standard mix proportion according to those of domestic PC factories to establish a basic data for the Accelerated Curing Effect. The experimental tests were conducted according to the conditions of each sub-curing periods. By comparing the results of compression tests on de-molded and 28-day water-curing specimens, we find that the most effective curing condition to obtain more than the required design strength after 28 day of water curing may be as follows: the presteaming period does not affect seriously and less than$30^{circ}C/hr$- the rate of temperature rise andless than $82^{circ}C$ - maximum temperature are necessary. It seems that post-curing procedure is very important factor to increase the effect of accelerated curing.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.1
• /
• pp.17-24
• /
• 2008

Many problems exist in the current cast in place concrete lining used in domestic tunnel construction. Especially, the crack of tunnel lining brings about a social and economic problem. It has a lot of influence on stability of structure and the fine finish of lining. So enormous repair-work and reinforcement of tunnel lining could occur an running out of government's budget. In our country, there are domestic production enterprises which produce a special pre-cast concrete product, but the technical level of them is still far behind compared to developed countries. Also, optimum steam coring method is important for the production of high quality product. But there is no regulation of steam curing method in our country. This study is to investigate the properties of PC panel according to the variation of steam curing conditions such as presteaming time and rate of temperature rise. The result shows that the optimum presteaming time of steam curing method in PC panel is more than 1 hour and the desirable rate of temperature in curing chamber is about $20^{\circ}C/hr$.

• Korean Journal of Agricultural Science
• /
• v.31 no.1
• /
• pp.9-14
• /
• 2004

This study was carried out for deresinning the larch boards dried in a conventional kiln. Prior to heat treatment they were steamed in an autoclave for 5 hours or frozen for 24 hours at a temperature of $-35^{\circ}C$. The velocities of ultrasound transmitted through the specimens were measured to examine the correlation with their resin contents. It was found that the specimens heated at $100^{\circ}C$ for 5 hours contained less resin that those heated at $200^{\circ}C$ for an hour. Both treatments of steaming and freezing were effective for deresinning and the former was better than the latter. The ultrasonic velocities measured before the heat treatment showed a negative correlation to the resin contents of the specimens, but those measured after the heat treatment a positive correlation. This difference may be attributed to the viscosity of resin.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.28-32
• /
• 1995

The presteamed or prefrozen persimmon blocks of 10cm ${\times}$ 10cm ${\times}$ 15cm were air-dried at room temperature until about 30% moisture content, and then were dried in a MW oven. During drying their internal temperatures were monitored with thermo-couple probes. The presteamed and prefrozen blocks didn't show any improvement in drying rate and moisture gradient when compared with the controls. Checks appeared on the surfaces of most presteamed blocks during air-drying. It has been clearly revealed that the maximum weight, loss must, be less than 2g/min during MW drying to prevent internal checking and that MW drying reduced moisture gradients inside blocks. MW dried the persimmon blocks 440 times faster than conventional kiln.