• 대한기계학회논문집B
• /
• 제20권10호
• /
• pp.3251-3261
• /
• 1996

Flows were measured in an unshrouded centrifugal impeller. By using a single slanted hot-wire probe and a Kiel probe mounted on the impeller hub disk, the 3-D relative velocities and the rotary stagnation pressures were measured in seven circumferential planes between the inlet and outlet of the impeller rotating at 700 rpm, which diameter is 0.39 meter, and the static pressures and the slip factor at the impeller outlet were estimated from the measured values. Measurements were made for three flow rates corresponding to zero incidence and two others with the greater and the smaller one than zero. From the measured data in these flow rates, the followings were investigated in the impeller passage, the variation of the primary and secondary flows, the leakage flows, the wake's position and its size, the static pressure rise and the loss production mechanism. Furthermore the static pressure and the slip factor were compared with the results of inviscid Quasi-3D calculation.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.132-139
• /
• 2010

This paper describes an investigation of the performance and emission characteristics of a commercial cylinder direct injection diesel engine operating on natural gas with pilot diesel ignition. Engine tests for variations in the pilot injection timing were performed at an engine speed of 1500 rpm. This study showed that the performance of the dual-fuel diesel engine increased as the engine load increased and as the pilot diesel injection timing angle advanced. The peaks of cylinder pressure, pressure rise rate, and heat release rate all increased while the fuel ignition timing advanced with the pilot injection timing. The engine operation was stable, and the least smoke was produced at a pilot injection timing of $12^{\circ}$ before top dead center. NOx emissions were only exhausted under high-load conditions, and they increased as the pilot injection timing angle advanced.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.123-128
• /
• 1994

A high speed spindle system for machine tools can be used to reduce the machining time, to improve the machining accuracy, to perform the machining of light metals and hard materials, and to unite the cutting and grinding processes. In this study, a high speed spindle system is developed by applying the oil-air lubrication method, angular contact ball bearings, injection nozzles with dual orifices, cooling jacket and so on. And an air cooling experiment for evaluating the performance of the spindle system is carried out. Especially, in ofder to establish the air cooling conditions related to the development of a high speed spindle system, the effects of cooling air pressure, oil supply rate, air supply rate and rotational spindle speed are studied and discussed on the bearing temperature rise and frictional torque. Also the effects of cooling air pressure, rotational spindle speed and spindle system structure is investigated on the bearing temperature distribution. The experiment on the test model reveals the usefulness of the air cooling method.

• 한국임상수의학회지
• /
• 제28권1호
• /
• pp.40-45
• /
• 2011

Cardiovascular changes caused by $CO_2$ pneumoperitoneum during laparoscopic ovariohysterectomy (LOVH) were measured in nine healthy mixed breed dogs ($16.7{\pm}4.6kg$). The dogs were premedicated with the combination of atropine, acepromazine, and butorphanol. General anesthesia was induced with propofol and maintained with isoflurane in oxygen. Controlled ventilation maintained partial pressure of end-tidal $CO_2$ between 35-45 mmHg. The $CO_2$ pneumoperitoneum was maintained at a constant pressure of 12 mmHg and the dog was placed in the $15^{\circ}$ Trendelenburg position as LOVH was performed. Dorsal pedal artery was catheterized for measurements of heart rate (HR) and invasive arterial blood pressure (IBP). Prior to the intraperitoneal insufflation, baseline measurements of HR and IBP were made every minute for a total of 10 min. Then, measurements of HR and IBP were made every 5 min following intraperitoneal insufflation and were also made every 5 min following desufflation for a total of 10 min. The $CO_2$ pneumoperitoneum during LOVH resulted in a significant (P < 0.05) increase in systolic arterial blood pressure at the time of the onset of insufflation. In addition, diastolic and mean arterial blood pressure increased significantly (P < 0.05) at the time of the onset of insufflation and 5 min following insufflation. The mean heart rate did not change significantly during LOVH. Although IBP showed sharp initial rise following the $CO_2$ pneumoperitoneum, the changes were within physiological acceptable limits in these healthy, ventilated dogs.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.678-683
• /
• 2001

The present work has carried out experimental study on a cross-flow fan system with a simplified vortex wall scroll casing. A cross-flow fan test rig was constructed to obtain pressure rise and volume flow rate for various fan operating conditions. The performance estimation is using a wind tunnel with a motor driven damper for flow rate control and flows are quantitatively visualized by light scattering system with a pulsed laser. Min focus on the visualization is finding a eccentric vortex inside a fan which is a major factor reducing fan efficiency. Comprehensive engineering data are prepared for industrial applications and show a good agreement with a prior work by experimental measurements.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.840-844
• /
• 2003

A study for increase of fan flow rate by geometric modification has been conducted to decrease temperature rise of marine generator inner part. Through experiment of a real product, a performance curve for various flow resistances was obtained. Flow analyses for each cases were done by using commercial code-FLUENT and the results were very similar to experimental data (0.7% deviation at normal operating condition). Through flow analysis results for various design geometric modification, a scroll type fan was adopted as a best design geometry with 100Pa more pressure and 22% more flow rate than original fan.

• 대한기계학회논문집B
• /
• 제25권3호
• /
• pp.373-380
• /
• 2001

In this study, a single Taylor bubble and a train of Taylor bubbles rising in a vertical tube were simulated numerically. A finite difference method was used to solve the mass and momentum equations for the liquid-gas region. The liquid-gas interface was captured by a level set function which is defined a signed distance from the interface. For a train of Taylor bubbles repeated periodically in space, the periodic conditions were imposed at the boundaries normal to the gravitational direction and the pressure boundary conditions were iteratively determined so that the computed flow rate should be equal to a given flow rate. Based on the numerical simulation, the calculated shape and rise velocity of a Taylor bubble were found to be in good agreement with the experimental data reported in the literature.

• Korean Chemical Engineering Research
• /
• 제61권1호
• /
• pp.80-88
• /
• 2023

저밀도 폴리에틸렌(Low-density polyethylene, LDPE)은 분진폭발 관련 특성치에 대한 기준이 제시되고 있지 않아 제조 및 취급설비의 안전한 설계가 어렵다. 이 연구에서는 LDPE 제조공정 중 Bag Filter에서 채취한 분진(LDPE 1)과 Silo 등의 설비 외부에 누설된 퇴적 분진(LDPE 2)에서 채취한 2개 시료에 대하여 분진폭발 시험을 수행하였고 그 중 LDPE 2 분진에 대하여 요약하였다. 입도분석 결과, 체적기준 평균입경은 95.04 ㎛, 수밀도는 0~1 ㎛로 나타났다. 최대폭발압력(P_max)은 6.6 bar, 최대폭발압력상승속도는 1500 g/m³에서 366 [bar/s]로 분진폭발지수(K_st)는 99.4 bar·m/s로 ST-1 등급임을 확인하였다. 또한, 최소점화에너지는 10 mJ이며 최소점화온도는 450 ℃로 나타났다. 현재, 제조 및 취급 설계는 고밀도 폴리에틸렌(HDPE)의 특성값을 기초로 한다. 그러나, 시험 결과 LDPE 2 분진이 HDPE(입자지름 61.6 ㎛)보다 위험성이 높은 것으로 나타나 LDPE 제조공정에서 HDPE 설계기준을 적용할 때는 주의가 필요하다.

• 한국건축시공학회지
• /
• 제15권3호
• /
• pp.291-297
• /
• 2015

본 연구에서는 초고층 구조물 시공에 사용되는 80MPa의 고성능 콘크리트를 대상으로 높이가 200m부터 350m인 지점까지 압송계측 결과를 근거로 하여 압송성능과 고성능 콘크리트의 유동특성과의 상관관계를 분석하였다. 굳지 않은 콘크리트의 물성과 초기강도 및 기준 재령에서의 압축강도 및 탄성계수는 모두 품질기준을 만족함이 확인되었다. 또한, 높이별 최대 압송압력은 약 10~15%씩 증가하였으며, 시간당 토출량은 최소 $25m^3$를 만족하는 것으로 나타났다. 또한, 압송압력과 마찰계수는 슬럼프 플로우의 크기에 반비례하는 것으로 나타났으며, 압송압력과 마찰계수는 T-500이 높을수록 증가하는 경향을 보였다.

• 국제초고층학회논문집
• /
• 제8권2호
• /
• pp.101-106
• /
• 2019

Assessing the energy performance of supertall buildings often does not consider variations in energy consumption due to the change of environmental conditions such as temperature, pressure, and wind speed associated with differing elevations. Some modelers account for these changing conditions by using a conventional temperature lapse rate, but not many studies confirm to the appropriateness of applying it to tall buildings. This paper presents and discusses simulated annual energy consumption results from a 600 m tall skyscraper floor plate located in Dubai, UAE, assessed using ground level weather data, a conventional temperature lapse rate of $6.5^{\circ}C/km$, and more accurate simulated 600 m weather data. A typical office floorplate, with ASHRAE 90.1-2010 standards and systems applied, was evaluated using the EnergyPlus engine through the OpenStudio graphical user interface. The results presented in this paper indicate that by using ground level weather data, energy consumption at the top of the building can be overestimated by upwards of 4%. Furthermore, by only using a lapse rate, heating energy is overestimated by up to 96% due to local weather phenomenon such as temperature inversion, which can only be conveyed using simulated weather data. In addition, sizing and energy consumption of fans, which are dependent both on wind and atmospheric pressure, are not accurately captured using a temperature lapse rate. These results show that that it is important, with the ever increasing construction of supertall buildings, to be able to account for variations in climatic conditions along the height of the building. Adequately modeling these conditions using simulated weather data will help designers and engineers correctly size mechanical systems, potentially decreasing overall building energy consumption, and ensuring that these systems are able to provide the necessary indoor conditions to maintain occupant comfort levels.