• Fashion & Textile Research Journal
• /
• v.10 no.5
• /
• pp.676-682
• /
• 2008

In this study a guideline of the 3D-fit pattern for the ECG(electrocardiogram) measurement of elderly's u-healthcare clothes was proposed. In the screening test of the ECG measurement band, ECG peak band was observable at the band pressure of 0.20 kPa. By employing a 3D body image, tight-fit 3D patterns were made at two different reduction rates of 21%(pattern 1) and 33%(pattern 2), and corresponding pressure of both of the clothes were 0.25 kPa and 0.54 kPa, respectively. Typical waves of ECG were found in both stationary and moving position. In terms of the subjective evaluation of the u-healthcare clothes when worn, it was confirmed that reduction pattern 1(0.25 kPa) conveyed comfortable clothing pressure and pleasantness, which is very close to the result of screening test of ECG band experiment. As results, it is recommended that reduction rate should be adjusted, so that clothing pressure is about 0.2 kPa for the elderly's comfortable and efficient u-healthcare clothes.

• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.22-29
• /
• 2018

The purpose of this study is to investigate the macroscopic spray characteristics and spray pattern of a gasoline direct injection (GDI) injector according to the increase of injection pressure. The macroscopic spray characteristics, such as a spray tip penetration and spray angle, were measured and analyzed from the frozen spray images, which are obtained from the spray visualization system including the high-speed camera, light-source, long-distance microscope (LDM). The spray pattern was analyzed through the deviation of the center of the spray plum and images were acquired using Nd: YAG Laser and ICCD(Intensified charge coupled device) camera. From the experiment and analysis, it revealed that the injection pressure have a significant influence on the spray tip penetration and spray pattern. However, the injection pressure have little influence on the spray angle. The increase of injection pressure induced the reduction of a closing delay. In addition, the deviation of spray center increase with the increase of injection pressure and the distance from a nozzle tip.

• PNF and Movement
• /
• v.18 no.1
• /
• pp.55-64
• /
• 2020

Purpose: The purpose of this study was to compare the strength and walking ability of chronic stroke patients following either proprioceptive neuromuscular facilitation (PNF) pattern training with pressure biofeedback units (feedback group) or PNF pattern training without pressure biofeedback units (control group). Methods: Eighteen participants with chronic stroke were recruited from a rehabilitation hospital. They were divided into two groups: a feedback group (n = 8) and a control group (n = 10). They all received 30 minutes of neurodevelopmental therapy and PNF training for 15 minutes five times a week for three weeks. Muscle strength and spatiotemporal gait parameters were measured. Muscle strength was measured by hand-held dynamometer; gait parameters were measured by the Biodex Gait trainer treadmill system. Results: After the training periods, the feedback group showed a significant improvement in hip abductor muscle strength, hip extensor muscle strength, step length of the unaffected limb, and step time of the affected limb (p<0.05). Conclusion: The results of this study showed that proprioceptive neuromuscular facilitation pattern training with pressure biofeedback units was more effective in improving hip muscle strength and walking ability than the proprioceptive neuromuscular facilitation pattern training without pressure biofeedback units. Therefore, to strengthen hip muscles and improve the walking ability of stroke patients, using pressure biofeedback units to improve trunk stability should be considered.

• Journal of Advanced Marine Engineering and Technology
• /
• v.4 no.1
• /
• pp.23-31
• /
• 1980

The fluid static pressure has been generally measured by means of a small hole leading to a measuring instrument. In case of viscoelastic fluids, however, it has been shown experimentally that a systematic error exists in measuring the static pressure by means of the small hole becuase viscoelasitc fluids have many properties that can not be observed in Newtonian fluids. In this paper, in order to examine the mechanism of the errors in measuring the static pressure of viscoelasitc fluids, flow patterns in the vicinity of static pressure measuring hole were photographically taken and observed graphically. The experiments to take photographs of flow patterns were performed by a parallel plate channel with the steady two-dimensional shear flow of viscoelastic fluids. Results of the experiment are classified as following three regions; (1) Arched symmetrical flow pattern region. (2) Asymmetrical flow pattern region. (3) Rectilinear symmetricl flow pattern region.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.90-97
• /
• 2003

The purpose of this study is to understand the dissipation pattern of excess pore pressure after liquefaction which governs the post-liquefaction behavior of liquefied sand deposits. 1-g shaking table tests were carried out on 5 different kinds of sands, all of which had high liquefaction potentials. During the tests excess pore pressure at various depths, and surface settlements were measured. The measured curve of the excess pore pressure dissipation was simulated using the solidification theory, and from the analysis of the velocity of dissipation, the dissipation pattern of excess pore pressure after liquefaction was examined. The dissipation velocity of excess pore pressure after liquefaction had a linear correlation with the effective grain size ( $D_{10}$) divided by the coefficient of uniformity ( $C_{u}$), and the increase in the initial relative density of the ground played a role in shifting this correlation curve toward an increased dissipation velocity. From the correlation, an approximate method was recommended for prediction of the dissipation curve of excess pore pressure after liquefaction in saturated sand deposits.s.s.

• Journal of the Korean Home Economics Association
• /
• v.34 no.2
• /
• pp.43-55
• /
• 1996

The purpose of this study was to investigate the slacks pattern making on the movement-fitness of the knee region. The experimental items were divided into the lower limb movement (M1~M5) and slacks pattern designs (4 : basic pattern, in-pleats, side-pleats, seam-line increase). This study was done by clothing pressure test, sensory evaluation test and the difference shape-transformation of wearing-slacks. The summarized finding resulted from experiments and investigation are suggested as follows ; First, the clothing pressure test showed that the order of clothing pressure in the movement was the rabbit leap movement (M3), the sit on knees (M4), the nobleman sitting (M5), the sit on chair (M2) from the highest to the lowest. In the comparison of clothing pressure tested by blocks of lower-limb, center front knee region shows the highest of 300g/cm2. In it by constructional methods, the clothing pressure of in-pleats, side-pleats methods shows lower than basic pattern, hem-line increase methods. Also in comparison of the two methods, in-pleats method shows lower than side-pleats method. Second, by the sensory evaluation test based on the lower-limb movements and constructional methods of slacks, it was found that the functional factor score of the rabbit leap movement was also the waist, hip, knee region was the lowest in all blocks. And in the comparison of constructional methods, in-pleats method was the highest in all methods. Third, in consideration of the difference in the shape-transformation of wearing-slacks on the movement-fitness, pleats pattern design methods showed that the ratio of shape-transformation was lower than basic on seam-line increase methods. But the difference of the side-pleats and in-pleats methods was litle. According to these investigation, the slacks pattern making caused by movement-fitness on the knee region, in-pleats design method was the functional slacks pattern.

• The Journal of Korean Physical Therapy
• /
• v.32 no.1
• /
• pp.29-33
• /
• 2020

Purpose: This study examined the effects of the weight-bearing pattern and calcaneal taping on the heel width and plantar pressure in standing. Methods: Fifteen healthy subjects with normal feet participated in this study. The heel width was measured using a digital caliper, and a pedoscan was used to measure the plantar pressure of the rear foot while standing. The participants were instructed to stand in three weight-bearing patterns (anterior, middle, and posterior weight bearing) before and after calcaneal taping. The heel width and plantar pressure were measured three times before and three times after calcaneal taping, with the three weight-bearing patterns applied in random order. A 2 (non-taping vs. taping) × 3 (anterior, middle, posterior weight bearing) two-way repeated ANOVA with a Bonferroni post hoc correction was used to assess the differences in heel width and plantar pressure. Results: The results revealed a significant main effect of the weight-bearing pattern (p<.01), but not of calcaneal taping (p>.05). Greater weight bearing applied to the heel resulted in a significantly increased heel width and planter pressure of the rear foot (p<.01). Conclusion: In standing, a posterior weight-bearing pattern increases the heel width due to side-to-side shifting of the plantar heel pad, which increases the heel plantar pressure. Therefore, to prevent high stress on the heel pad and plantar heel pain, it is important to refrain from posterior weight bearing while standing during the activities of daily living.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1537-1541
• /
• 2007

We injection molded a wedge type of plate with micro prizm patterns on its surface and investigated the fidelity of replication of the micro pattern depending on the process parameter such as mold temperature, melt temperature, injection rate or packing pressure. The size of the size of the $90^{\circ}$ prizm pattern is $50{\mu}m$ and the size of the plate is about 300㎜${\times}$200㎜. The thicknesses are 2.6㎜. and 0.7mm at each edge of the wedge type of plate. The fidelity of the replication turned out quite different according to the process parameters and location of the patterns on the plate. We measured the cavity pressure and temperature in real-time during the molding to analyze the effect of the local melt pressure and temperature on the micro pattern replication.

• Journal of the Korean Home Economics Association
• /
• v.35 no.4
• /
• pp.159-172
• /
• 1997

The purpose of this study was to investigate the slacks pattern making on the movement -fitness of the hip region. The experimental items were divided into the 5 lower limb movements(M1-M5) and the 12 revision pattern constructions of slacks. This study was done by clothing pressure test sensory evaluation test and the difference shape-transformation of wearing-slacks. The summarized finding resulted from experiments and investigation are suggested as follows: First by the clothing pressure tested by lower limb movements the clothing pressure score of the rabbit leap movement(M3) was the highest of all lower limb movements and the order of it in the another movement was the sit on knee(M4) the sit on chair(M2) the noble sitting(M5) from the highest to the lowest. And in comparision of clothing pressure tested by revision pattern to cover the extend of crotch-length 20。 inclined back-line construction method (CA4) showed the lowest. And in comparision of clothing pressure tested by revision pattern to cover the extend of crotch-length 20。 inclined back-line construction method (CA4) showed the lowest. And also for a role to cover hip circumference extendign CC4(1/5 hip.1cm longrightarrow linked back -line) method showed the lowest. Second by the sensory evaluation test based on the movement and revision patterns it was found that the functional factor score of the rabbit leap movement was the lowest in all movement however the score of revision patterns were higher than basic pattern. Third by the test to show difference in the shape-transformation of wearing-slacks on chair(M2) also need to be analyzed. The ration of the shape-transformation of the knee region showed the least value in the increased patterns of inclined angle of back-line(CA) and the differential methods of back-line inclined pattern making. But that of the hem-line did not show remarkable difference.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.100-104
• /
• 2005

The injection molding is very effective process for various plastic products due to its high productivity. It is also good fur precise products like optical parts. Various thermoplastic materials are also available with this injection molding process. In recent, however, as the overall size of the product increases and micro or nano scale of patterns are applied to the products, we now have some problems such as low fidelity of the replication of the pattern, high molding pressure, or warpage from the in-mold stress. Injection/compression molding is studied to overcome those problems in molding large thin plate with micro pattern array on its surface. An injection compression mold is designed to 3 pieces mold for side gate. We install 4 pressure transducers and 9 thermocouples to measure the melt pressure and surface temperature in the cavity during the process. As a result, the maximum molding pressure for injection compression molding is reduced to 1/3 compared to injection molding and the uniformity of the pressure in the cavity is enhanced by about 15%.