• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.221-226
• /
• 2014

This paper described the effect of split injections on the stability of combustion and emission characteristics in a direct injection gasoline engine at various operating conditions. In order to investigate the influence of direct injection gasoline engine, the fuel injection timing was varied direct fuel injection at various fuel pressure. The experimental apparatus consisted of GDI engine with 4 cylinder, EC dynamometer, injection control system, and exhaust emissions analyzer. The emission and combustion characteristics were analyzed for the fuel injection timing and fuel injection pressure strategies. It is revealed that CO and HC emissions are dramatically decreased at advanced injection timing. Also, engine performance is increased at increase fuel injection pressure.

• Journal of ILASS-Korea
• /
• v.18 no.1
• /
• pp.61-65
• /
• 2013

In case of GDI engine, shape of injected fuel and injection mass are one of the most important factors for good fuel efficiency and power. But it should be too inefficient and difficult to acquire injection mass data by experiment because condition in engine vary with temperature, pressure, and so on. So, this paper suggests the AMESim (Advanced Modeling Environment for Simulation of Engineering Systems) as simulation program to calculate injection mass. For both simulation and experiment, n-heptane is used as fuel. In AMESim, I modeled the GDI injector and simulated several cases. In experiment, I acquired the injection mass using Bosch method to apply ambient pressure. The AMESim show reasonable result in comparison with experimental data especially at injection pressure 15 MPa. Other conditions are also in good accord with experimental data but error is a little bit large because the injection mass is so low.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.302-305
• /
• 2007

In recent years, many researches on new storage media with high capacity and information are developing. For manufacture of optical storage with high capacity, the injection molding process is generally used. In order to increase the filling ratio of the injection molding structure, the injection molding process required for high injection pressure, packing pressure and temperature control of the mold. However, conventional injection molding process is difficult to increase the filling ratio using injection master with the range of several nanometers and high aspect ratio. In order to improve and increase filling ratio of nano-structure with high aspect ratio, the active temperature control of injection mold was used. Experimental conditions were used injection pressure, time and temperature. Consequently, by using the peltier device into injection mold, we carried out the efficient and active temperature control of mold at low cost.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.53-58
• /
• 2019

This paper presents Artificial Neural Network(ANN) method to predict maximum injection pressure of injection molding machine and weights of injection molding products. 5 hidden layers with 10 neurons is used in the ANN. The ANN was conducted with 5 Input parameters and 2 response data. The input parameters, i.e., melt temperature, mold temperature, fill time, packing pressure, and packing time were selected. The combination of the orthogonal array L27 data set and 23 randomly generated data set were applied in order to train and test for ANN. According to the experimental result, error of the ANN for weights was $0.49{\pm}0.23%$. In case of maximum injection pressure, error of the ANN was $1.40{\pm}1.19%$. This value showed that ANN can be successfully predict the injection pressure and the weights of injection molding products.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.214-219
• /
• 2005

The effects of change in injection pressure on spray structure in high temperature and pressure field have been investigated. The analysis of liquid and vapor phases of injected fuel is important for emissions control of diesel engines. Therefore, this work examines the evaporating spray structure using a constant volume vessel. The injection pressure is selected as the experimental parameter, is changed from 72MPa to 112MPa by using a common rail injection system(ECD-U2). The images of liquid and vapor phase in the evaporating free diesel spray are simultaneously taken by exciplex fluorescence method. As a result, it can be confirmed that the distribution of vapor concentration is more uniform in the case of the high injection than in that of the low injection pressure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.22-28
• /
• 2003

Flash boiling mechanism in the injector interferes with fine fuel metering in a liquid phase LPG injection engine. This study presents a mathematical model to precisely predict an injection quantity. A calibration procedure of injection quantity, which is very prompt and precise in measuring, is developed using a gas analyzer. According to this procedure, injection quantity can be obtained under various fuel compositions, temperatures and injection pressures. The release pressure of liquid phase LPG is estimated based on these experimental data. Although the release pressure is much lower than the saturation pressure, it is linearly proportional to the saturation pressure.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.31-37
• /
• 2004

This paper presents spray and combustion characteristics of hydrocarbon fuel injected from pressure-swirl nozzles. Three commercial nozzles with orifice diameters of 0.256, 0.308 and 0.333mm and injection pressures ranging from 0.7 to 1.3 MPa were selected f9r the experiments. Spray characteristics such as breakup length. spray angle and drop size (SMD) were analyzed using photo image analyses and Malvern Panicle Size Analyzer. The drop size was measured with and without a blower at the same measuring locations. The flame length and width were measured using photo image analyses. The temperature distribution along the axial distance and the gas emission such as CO, $CO_2\;and\;NO_x$ were studied. The breakup length decreased with an increase in injection pressure for each nozzle but increased with an increase in nozzle orifice diameter. The spray angle increased and SMD decreased with an increase in injection pressure. The flame with an increased linearly with an increase in injection pressure and in nozzle orifice diameter. The flame temperature increased with an increase in injection pressure but decreased along the axial distance. The maximum temperatures occurred closer to the burner exit and flame at axial distance of 242mm from the diffuser tip. The experimental results showed that the level of CO decreased while that of $CO_2\;and\;NO_x$ increased with an increase in injection pressure and nozzle orifice diameter.

• Archives of Plastic Surgery
• /
• v.37 no.3
• /
• pp.245-249
• /
• 2010

Purpose: High-pressure injection injury is caused by accidental injection of the high-pressure injection devices in industry. The initial benign appearance of the wound fools patients into delays in an adequate treatment. And it can result in disastrous outcomes such as necrosis and amputation. To avoid the poor prognosis, the injuries require a prompt surgical intervention. The purpose of this article is to recognize the poor outcome of the highpressure injection injury and to introduce an adequate treatment in need. Methods: We have 4 cases of the high-pressure injection injuries in the hand from April, 2005 to March, 2009. Average age is 39 years (30 - 49 years old), 2 cases are the palm of dominant hand, 1 case is the thumb of dominant hand, and 1 case is the palm of non-dominant hand, respectively. We followed up these patients for 20 months on average. In 3 cases, the immediate, aggressive surgical intervention was carried out, but the other one was delayed in early adequate treatment. The wounds were covered by local advancement flap, anterolateral thigh free flap, conservative treatment with antibiotics and dressing. Results: No pathogens after culture were found nor any findings of fracture in imaging study. Conservative treatment, local advancement flap and anterolateral thigh free flap for the open wound resulted in a desirable aesthetic outcome. In a long-term follow up, functional capability of the patient was also satisfactory. Conclusion: Upon initial evaluation, most high-pressure injection injuries present as innocuous wounds with very few symptoms and result in delaying the proper management. And the majority of high-pressure injection injuries will produce significant morbidity to the hand, amputation. And the initial aggressive surgical debridement was needed to prevent the poor outcome. The key to success in treating high-pressure injection injuries of the hand is the prompt aggressive surgical intervention.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.338-344
• /
• 2016

The study is actively being performed to increase fuel injection pressure of common rail system among countermeasures to meet the emission regulation strengthen of the Diesel engine. The common rail fuel injection tube in such ultra high pressure common rail system has the weakest structural characteristics against vibration that is generated by fuel injection pressure and pulsation during engine operation and driving. Thus the extreme durability is required for common rail fuel injection tube, and the drawing process is being magnified as the most important technical fact for strength of seamless pipe that is the raw material of common rail tube. In this respect, we analyzed the characteristic of dimension and stress variation of the ultra high pressure common rail fuel injection tube by variation of Die and Plug angle in drawing process. Based on the analysis, we tried to obtain the raw material strength of common rail fuel injection tube for applying to the ultra high pressure common rail system. As a result, Plug angle is more important than entry angle of Die and we could obtain the target dimension and strength of the ultra high pressure common rail fuel injection tube through optimization of Plug angle.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.10-16
• /
• 2005

To investigate the effect of shockwave on diesel spray characteristics under ultra high pressure injection, the velocity of spray tip and shock wave were investigated using the visualization of spray by schlieren method. Spray characteristics such as the spray radius, height, and droplets size were analyzed. It is found in this study that shock wave, produced by ultra high injection pressure, propagates faster than spray tip. Spray radius of right side of nozzle tip was shorter than that of left side and spray height of right side of nozzle tip was thicker than that of left side. Droplets sue was increased at 414MPa in injection pressure because of pressure gradient between inner and outer of tile spray caused by shockwave.