• Geomechanics and Engineering
• /
• v.16 no.3
• /
• pp.273-284
• /
• 2018

A detailed understanding of the mechanical behaviors for crushed coal rocks after grouting is a key for construction in the broken zones of mining engineering. In this research, experiments of grouting into the crushed coal rock using independently developed test equipment for solving the problem of sampling of crushed coal rocks have been carried out. The application of uniaxial compression was used to approximately simulate the ground stress in real engineering. In combination with the analysis of crack evolution and failure modes for the grouted specimens, the influences of different crushed degrees of coal rock (CDCR) and solidified grout strength (SGS) on the mechanical behavior of grouted specimens under uniaxial compression were investigated. The research demonstrated that first, the UCS of grouted specimens decreased with the decrease in the CDCR at constant SGS (except for the SGS of 12.3 MPa). However, the UCS of grouted specimens for constant CDCR increased when the SGS increased; optimum solidification strengths for grouts between 19.3 and 23.0 MPa were obtained. The elastic moduli of the grouted specimens with different CDCR generally increased with increasing SGS, and the peak axial strain showed a slightly nonlinear decrease with increasing SGS. The supporting effect of the skeleton structure produced by the solidified grouts was increasingly obvious with increasing CDCR and SGS. The possible evolution of internal cracks for the grouted specimens was classified into three stages: (1) cracks initiating along the interfaces between the coal blocks and solidified grouts; (2) cracks initiating and propagating in coal blocks; and (3) cracks continually propagating successively in the interfaces, the coal blocks, and the solidified grouts near the coal blocks. Finally, after the propagation and coalescence of internal cracks through the entire specimens, there were two main failure modes for the failed grouted specimens. These modes included the inclined shear failure occurring in the more crushed coal rock and the splitting failure occurring in the less crushed coal rock. Both modes were different from the single failure mode along the fissure for the fractured coal rock after grouting solidification. However, compared to the brittle failure of intact coal rock, grouting into the different crushed degree coal rocks resulted in ductile deformation after the peak strength for the grouted specimens was attained.

• Design & Manufacturing
• /
• v.13 no.4
• /
• pp.10-16
• /
• 2019

Semiconductor chip is bonded to the substrate by melting solder bumps. In general, the chip bonding is applied by a Reflow process or a Thermo-Compression(TC) bonding process. In this paper, we introduce a Laser Assisted Thermo-Compression bonding (LATCB) process to improve the anxiety of the existing process(Reflow, TC bonding). In the LATCB process, the chip is bonded to the substrate by irradiating a laser with a uniform energy density in the same area as the chip to melt only the solder bumps and press the chip with a Transparent Compression Module (TCM). The TCM consists of a fused silica header for penetrating the laser and pressurizing the chip, and a piezoelectric actuator (P.A.) coupled to both ends of the header for micro displacement control of the header. In addition, TCM is a structure that can pressurize the chip and deliver it to the chip and solder bumps without losing the energy of the laser. Fused silica, which is brittle, is vulnerable to deformation, so the header may be damaged when an external force is applied for pressurization or a displacement differenced is caused by piezoelectric actuators at both ends. On the other hand, in order to avoid interference between the header and the adjacent chip when pressing the chip using the TCM, the header has a notch at the bottom, and breakage due to stress concentration of the notch is expected. In this study, the thickness and notch length that the header does not break when the external force (500 N) is applied to both ends of the header are optimized using structural analysis and Coulomb-Mohr failure theory. In addition, the maximum displacement difference of the P.A.s at both ends where no break occurred in the header was derived. As a result, the thickness of the header is 11 mm, and the maximum displacement difference between both ends is 8 um.

• Journal of Preventive Medicine and Public Health
• /
• v.1 no.1
• /
• pp.79-86
• /
• 1968

This paper describes the incidence and some epidemiological features of drowning accident out of a series of our study on the epidemiology of various accidents in Korea. By the daily press it is apparent from the frequent reporting of swimming accidents that the incidence would be high. In the rural areas, there are, at present, about 1,250 artificial lakes and farm ponds to be utlized for rice production. The reservoirs, irrigation ditches and riversides are also used for recreation. In most places facilities for aquatic activities is meager, and safety measures for the prevention of drowning is not sufficiently enforced. In the survey crude data on drownings were collected from the concerned governmental statistic books for the period 1955 to 1967 which were compiled not in a uniform way. Drownings were classfied into two categories, one is accidental drowning, E 929 and the other is due to cataclysm, E 934, according to the WHO international classification of diseases. Epidemiological variables in relation to drowning accident were obtained through qualitative analysis of informations from the popular news papers. The following summary may be drawn; 1. The average number of deaths due to accidental drowning totaled 1,088 annually and the mortality rate per 100,000 population was 3.4, The 42.0% of all drownings were rescued and the remaining were not saved. 2. The sex ratio (M/F) of the victims for all ages was 5 to 1, which had a wide range of difference among the age groups. The young ages less than 20 years occupied 68.0% of all deaths. 3. The percentage distribution of the causes of accidents revealed 31.9% for careless swimming, 45.5% for unskilled, 10.6% for swimmer's cramp and 6.0% for drunked. The distribution of places where accidents occurred showed 88.0% for rivers, water reservoirs, irrigation ditches and 12.0% for regular swimming pools. The seasonal distribution of cases indicated 85.0% of the total were seen during the summer months, June-August, and 50.0% of them occurred on Sundays, 4. The average annual deaths due to cataclysm were 402 and mortality rate per 100,000 population was 1.6, but the number of victims due to cataclysm varied greatly each year. 5. The accident cases due to cataclysm were classified into 60.0% for injuries, 40.0% for deaths. The 26.8% of all deaths were missing cases. 6. The deaths due to either accidental drowning or cataclysm totaled 1,490, and the death rate per 100,000 for the whole country was 5.0.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.63 no.2
• /
• pp.158-163
• /
• 2018

Perilla (Perilla frutescens var.frutescens) is an annual plant of the Lamiaceae family, mainly grown for obtaining oil by press extraction after roasting the seeds. Oil yield is one of its important traits, but evaluating this yield is time-consuming, requires many seeds, and is hard to adjust to pedigrees in a breeding field. The objective of this study was to develop a method for selecting high-oil-yield lines in a breeding population without oil extraction. Twenty-three perilla cultivars were used for evaluating the oil yield and seed traits such as seed hardness, seed coat thickness, seed coat proportion and crude fat. After evaluation of the seed traits of 23 perilla cultivars, the ranges of oil yields, seed hardness, seed coat thickness, seed coat proportion, 100-seed weight, and crude fat were 24.68-38.75%, 157-1166 gf, $24-399{\mu}m$, 15.4-41.5%, 2.79-6.69 g, and 33.0-47.8%, respectively. In an analysis of correlation coefficients, the oil yield negatively correlated with seed length, seed width, the proportion of seed coat, seed hardness, and 1000-seed weight, but positively correlated with crude fat content. It was observed that as the seed coat proportion increased, the seed coat thickness, hardness, and 1000-seed weight also increased. Multiple linear regression (MLR) was employed to find major variables affecting the oil yield. Among the variables, traits crude fat content and seed coat proportion were assumed to be indirect parameters for estimating the potential oil yield, with respect to a significant positive correlation with the observed oil yield ($R^2=0.791$). Using these two parameters, an equation was derived to predict the oil yield. The results of this study show that various seed traits in 23 perilla cultivars positively or negatively correlated with the oil yield. In particular, crude fat and the seed coat proportion can be used for predicting the oil yield with the newly developed equation, and this approach will improve the efficiency of selecting prominent lines for the oil yield.

• Journal of the Korean Home Economics Association
• /
• v.19 no.2
• /
• pp.11-24
• /
• 1981

The objectives of the study were to determine 1) if energy consumption and conservation vary in clothing, food, and housing with independent variables-size of household, homemaker's age, employment, and level of education, level of living, type of house, electricity use, and all energy use, and 2) if there is a correlation among energy conservation practices in clothing, food, and housing. Questionnaires wee given to the randomly selected homemakers in Seoul in July, 1980. Data from 620 responses were analyzed by F-test (Analysis of Variance) and Correlation. The results are as follows: 1. Clothing (1) the scores of the conservation practices I clothing were generally high. /However, it was found that a) they did not practice in wearing heavy under clothes and behavior outer clothing to cope with cool room temperature in the winter, b) they did not use bleach for laundry, but they used boiling method, and c) they did not have enough knowledge on Permanent Press finish. (2) energy conservation practices in clothing were significantly related to level of living and homemakrer's level of education. a) The higher the level of living, the higher scores in the knowledge were found. b) the higher the homeakcer's level of education, the higher scores in the knowledge and ironing were obtained. 2. Food (1) The scores of the conservation practices in food were generally high. However, it was found that scientific cooking methods were not performed such as a) to use measuring spoons, cups, and timers, b) to practice a simple method in using solor energy for warming water, c) to use thermos for the hot water tea or coffee, but they boiled water whenever necessary, and b) to use the pressure cooker whenever possible. (2) Energy conservation practices in food were significantly related to homemaker's employment and type of dwellings. a) The scores of full-time homemakers (not gainfully employed) were higher than gainfully employed homemakers. b) Families in traditional Korean dwellings revealed higher scores than those in apartment or western style dwellings. 3. Housing (1) The scores of the conservation practices in housing were generally high. However, it was found that a) they did not install fans in the kitchen, bathroom, and attic in the summer, b) they did not install a humidifier for tolerating a lower room temperature in the winer, c) they did not practice to make plans for the door of the refrigerator remained open for the shortest time, d) they did not install or use a local lighting with a general lighting for reading and cooking, and e) they usedaluminum foil without the knowledge of the heat reaction of its shiny and dull sides. (2) energy conservation practices in housing were significantly related to homemaker's employment and level of education, economic status, types of dwelling, and all energy use, a) Full-time homeakers had higher scores than gainfully employed homeakers. b) the higher the homemaker's level of education and economics status, the higher scores were obtained. c) Homeakers with their own house scored higher points than those with rented houses. And families in apartment or row houses scored higher points than those in traditional korean or western style dwellings. d) The higher the consumption rate of electricity and all energy, the higher scores were revealed. 4. correlation there was a significant correlation among energy conservation practices I clothing, food, and housing.

• PNF and Movement
• /
• v.14 no.1
• /
• pp.7-14
• /
• 2016

Purpose: The purpose of this study was to determine the effectiveness of direct and indirect methods of contract-relax techniques in proprioceptive neuromuscular facilitation (PNF) stretching for improving hamstring flexibility. Methods: Twenty-six subjects were randomly assigned to either a direct contract-relax technique group or an indirect contract-relax group. For each group, stretching intervention was performed three times a week for a period of two weeks, with 12 seconds for the contraction and 10 seconds for the relaxation per once. The direct contract-relax technique for hamstring flexibility was applied by asking the subject to press down on the shoulder of the trainer in the straight leg-raising position. Conversely, the indirect contract-relax technique was performed by raising the leg with resistance. To facilitate a comparative analysis of hamstring flexibility between the two groups before and after the stretching intervention, two-way repeated ANOVA was performed. Hamstring flexibility for each group was measured using a passive straight leg-raising test. Results: The results showed significant improvement in hamstring flexibility for all subjects in the two groups. However, there was no significant difference between the groups. Conclusion: In conclusion, both direct and indirect contract-relax techniques are confirmed to be useful for improving hamstring flexibility. The choice of suitable technique has to be made individually according to the condition of each subject.

• The Mathematical Education
• /
• v.27 no.1
• /
• pp.15-23
• /
• 1988

We are at the onset of a major revolution in education, a revolution unparalleled since the invention of the printing press. The computer will be the instrument of this revolution. Computers and computer application are everywhere these days. Everyone can't avoid the influence of the computer in today's world. The computer is no longer a magical, unfamiliar tool that is used only by researchers or scholars or scientists. The computer helps us do our jobs and even routine tasks more effectively and efficiently. More importantly, it gives us power never before available to solve complex problems. Mathematics instruction in secondary schools is frequently perceived to be more a amendable to the use of computers than are other areas of the school curriculum. This is based on the perception of mathematics as a subject with clearly defined objectives and outcomes that can be reliably measured by devices readily at hand or easily constructed by teachers or researchers. Because of this reason, the first large-scale computerized curriculum projects were in mathematics, and the first educational computer games were mathematics games. And now, the entire mathematics curriculum appears to be the first of the traditional school curriculum areas to be undergoing substantial trasformation because of computers. Recently, many research-Institutes of our country are going to study on computers in orders to use it in mathematics education, but the study is still start ing-step. In order to keep abreast of this trend necessity, and to enhance mathematics teaching/learning which is instructed lecture-based teaching/learning at the present time, this study aims to develop/present practical method of computer-using. This is devided into three methods. 1. Programming teaching/learning method This part is presented the following five types which can teach/learn the mathematical concepts and principle through concise program. (Type 1) Complete a program. (Type 2) Know the given program's content and predict the output. (Type 3) Write a program of the given flow-chart and solve the problem. (Type 4) Make an inference from an error message, find errors and correct them. (Type 5) Investigate complex mathematical fact through program and annotate a program. 2. Problem-solving teaching/learning method solving This part is illustrated how a computer can be used as a tool to help students solve realistic mathematical problems while simultaneously reinforcing their understanding of problem-solving processes. Here, four different problems are presented. For each problem, a four-stage problem-solving model of polya is given: Problem statement, Problem analysis, Computer program, and Looking back/Looking ahead. 3. CAI program teaching/learning method This part is developed/presented courseware of sine theorem section (Mathematics I for high school) in order to avail individualized learning or interactive learning with teacher. (Appendix I, II)

• Journal of Distribution Science
• /
• v.13 no.12
• /
• pp.33-40
• /
• 2015

Purpose - Given an increase in the consumption of plums, prices have fluctuated in an unstable manner, making it difficult for farmhouses to sell the product. This study intends to provide information on the cultivation and sale of plums to consumers, thus enabling producers to utilize relevant information to analyze the types of plums that are preferred and consumed by users. Research design, data, and methodology - In this study, a survey was conducted on plum consumption by a consumer panel established and operated by the Rural Development Administration in December 2009. The objective was to identify the purchasing awareness of plums and to analyze panel data from 2010 to 2013 using a linear regression model, a Tobit model, and a panel regression model to derive the purchase characteristics. Results - The outcome of the survey on plums is as follows. Plums are purchased because they are good for the health (90.6%), which means that most customers purchase plums for their health benefits. When plums are in season, the purchase rate is 94.8%, indicating that most plums are purchased when they are in season and that selling plums when they are out of season is difficult. Therefore, we sell most plums in the correct season, and the rest of the plums need to be processed and then sent to markets. The strongest reason for not purchasing plums is that they are difficult to process for consumption (63.1%), followed by the reason that the fruit is unfamiliar (15.5%). Regarding solutions for increasing the consumption of plums, the answers were as follows: distribute a recipe for plums (36.9%), advertise its effect through TV or the press (31.1%), and develop various processed products (15.6%). When customers decide to pick out plums, the major considerations were freshness (4.43), safe to eat (4.16), price (3.96), size (3.87), brand (3.28), and discount event (2.62). Freshness is important for decision making and safe to eat was more important than price because plums are washed and processed into plum jam. According to the results of the linear regression model, a higher family income results in a higher purchasing amount. However, the amount of plums purchased by a person was reduced if his or her income increased. Compared with individuals who used other purchasing agents on weekdays, those who used the traditional market turned out to purchase a higher amount of plums on the weekdays. Conclusions - Considering that numerous people purchase plums for their health benefits, promoting the consumption of plums is anticipated as being successful if they can be produced safely for consumption and for inclusion in recipes and various processed foods, and to promote eco-friendly agricultural practices.

• Ocean Systems Engineering
• /
• v.6 no.1
• /
• pp.23-60
• /
• 2016

The major objective of this study was to develop further understanding of 3D nearshore hydrodynamics under a variety of wave and tidal forcing conditions. The main tool used was a comprehensive 3D numerical model - combining the flow module of Delft3D with the WAVE solver of XBeach - of nearshore hydro- and morphodynamics that can simulate flow, sediment transport, and morphological evolution. Surf-swash zone hydrodynamics were modeled using the 3D Navier-Stokes equations, combined with various turbulence models (${\kappa}-{\varepsilon}$, ${\kappa}-L$, ATM and H-LES). Sediment transport and resulting foreshore profile changes were approximated using different sediment transport relations that consider both bed- and suspended-load transport of non-cohesive sediments. The numerical set-up was tested against field data, with good agreement found. Different numerical experiments under a range of bed characteristics and incident wave and tidal conditions were run to test the model's capability to reproduce 3D flow, wave propagation, sediment transport and morphodynamics in the nearshore at the field scale. The results were interpreted according to existing understanding of surf and swash zone processes. Our numerical experiments confirm that the angle between the crest line of the approaching wave and the shoreline defines the direction and strength of the longshore current, while the longshore current velocity varies across the nearshore zone. The model simulates the undertow, hydraulic cell and rip-current patterns generated by radiation stresses and longshore variability in wave heights. Numerical results show that a non-uniform seabed is crucial for generation of rip currents in the nearshore (when bed slope is uniform, rips are not generated). Increasing the wave height increases the peaks of eddy viscosity and TKE (turbulent kinetic energy), while increasing the tidal amplitude reduces these peaks. Wave and tide interaction has most striking effects on the foreshore profile with the formation of the intertidal bar. High values of eddy viscosity, TKE and wave set-up are spread offshore for coarser grain sizes. Beach profile steepness modifies the nearshore circulation pattern, significantly enhancing the vertical component of the flow. The local recirculation within the longshore current in the inshore region causes a transient offshore shift and strengthening of the longshore current. Overall, the analysis shows that, with reasonable hypotheses, it is possible to simulate the nearshore hydrodynamics subjected to oceanic forcing, consistent with existing understanding of this area. Part II of this work presents 3D nearshore morphodynamics induced by the tides and waves.

• Structural Engineering and Mechanics
• /
• v.31 no.2
• /
• pp.181-210
• /
• 2009

This paper presents the theoretical developments of an exact finite strip for the buckling and initial post-buckling analyses of isotropic flat plates. The so-called exact finite strip is assumed to be simply supported out-of-plane at the loaded ends. The strip is developed based on the concept that it is effectively a plate. The present method, which is designated by the name Full-analytical Finite Strip Method in this paper, provides an efficient and extremely accurate buckling solution. In the development process, the Von-Karman's equilibrium equation is solved exactly to obtain the buckling loads and the corresponding form of out-of-plane buckling deflection modes. The investigation of thin flat plate buckling behavior is then extended to an initial post-buckling study with the assumption that the deflected form immediately after the buckling is the same as that obtained for the buckling. It is noted that in the present method, only one of the calculated out-of-plane buckling deflection modes, corresponding to the lowest buckling load, i.e., the first mode is used for the initial post-buckling study. Thus, the postbuckling study is effectively a single-term analysis, which is attempted by utilizing the so-called semi-energy method. In this method, the Von-Karman's compatibility equation governing the behavior of isotropic flat plates is used together with a consideration of the total strain energy of the plate. Through the solution of the compatibility equation, the in-plane displacement functions which are themselves related to the Airy stress function are developed in terms of the unknown coefficient in the assumed out-of-plane deflection function. These in-plane and out-of-plane deflected functions are then substituted in the total strain energy expressions and the theorem of minimum total potential energy is applied to solve for the unknown coefficient. The developed method is subsequently applied to analyze the initial postbuckling behavior of some representative thin flat plates for which the results are also obtained through the application of a semi-analytical finite strip method. Through the comparison of the results and the appropriate discussion, the knowledge of the level of capability of the developed method is significantly promoted.