• Design & Manufacturing
• /
• 제8권2호
• /
• pp.41-45
• /
• 2014

Automated polishing apparatus based on the research have been developed. The research is improvement of polishing process for surface quality and uniformity improvement of preform injection mold core. Surface quality of preform core have influence on ejecting and product quality after injection molding. Thus, the current being made by hand to automate the polishing process, the surface of the preform to improve the quality and uniformity improvement. First made a division by analyzing manual process a step-by-step. And draw a mechanism for converting mechanical movement. Automated polishing apparatus for preform core was developed, through which shortens production time and were able to secure the safety of the worker.

• 소성∙가공
• /
• 제13권4호
• /
• pp.359-364
• /
• 2004

In the multi-stage former, a manufacture of hexagonal fitting nut was generated in a defective products about 70∼80% in the industry field. Products generated in defects manufactured to be a machining about 60%. Additional process increased a product cost and decreased a product rate. Therefore, it is important to predict and design a preform reducing defective products in the early stage of process design. So in the study Defects for manufacturing hexagonal fitting nut verified a cause through the finite element simulation. To reduce a defective generation. a preform designed and a designed preform verified through the finite element simulation. In conclusion, a generated defects when a hexagonal fitting nut manufactured should reduce if a round dimension of preform reduced and a part of opposition angle distributed in plenty a volume.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.83-86
• /
• 2003

Complete prediction of second order permeability tensor for three dimensional preform such as plain woven fabric and braided preform is critical to understand the resin transfer molding process of composites. The permeability can be obtained by various methods such as analytic, numerical, and experimental methods. For several decades, the permeability has studied numerically to avoid practical difficulty of many experiments. However, the predicted permeabilities are a bit wrong compared with experimentally measured data. In this study, numerical calculation of permeability was conducted for two kinds of preforms i.e., plain woven fabric and circular braided preform. In order to consider intra-tow flow in the unit cell of preform the proposed flow coupled model was used for plain woven fabric and the Brinkman equation was solved in the case of the braided preform.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 추계학술대회논문집
• /
• pp.157-166
• /
• 1995

A large crank shaft for ship engine consists of several components, such as throw, jornal, pin and flange. These compoents are individually made by open-die forging followed by machining and they are thermally fitted to form the crankshaft. In the present investigation, it was attempted to design an optimum preform for the throw by use of the spread coefficient. The spread coefficient found in the literature was confirmed by comparison with experimental results using plasticine. However, the preform designed by the spread coefficient was unable to produce the final product. The reason was found that the spread coefficient differs distinctly for the magnitude of bite ratio. Therefore, another spread coefficient, especially for low bite ratios, was proposed and the preform was redesigned. It was found that the new preform was able to produce the final product.

• Korea-Australia Rheology Journal
• /
• 제19권1호
• /
• pp.17-25
• /
• 2007

In liquid composite molding (LCM), composites are produced by impregnation of a dry preform with liquid resin. The resin flow through the preform is usually described by Darcy's law and the permeability tensor must be obtained for filling analysis. While the resin flow in the thickness direction can be neglected for thin parts, the resin flow in the transverse direction is important for thicker parts. However, the transverse permeability of the preform has not been investigated frequently. In this study, the transverse permeability was measured experimentally for five different fiber preforms. In order to verify the experimental results, the measured transverse permeability was compared with numerical results. Five different fiber mats were used in this study: glass fiber woven fabric, aramid fiber woven fabric, glass fiber random mat, glass fiber braided preform, and glass/aramid hybrid braided preform. The anisotropic braided preforms were manufactured by using a three dimensional braiding machine. The pressure was measured at the inlet and outlet positions with pressure transducers.

• 소성∙가공
• /
• 제8권2호
• /
• pp.135-142
• /
• 1999

Tube Process(TP) is one of the processes to produce permanent magnets. Advantage claimed for this process is that it can accmplish both densification and anisotropication in one step forming. This process is distinguished from other processes since it uses deformable tube for densification of powder magnets. TP has, however, difficulties in manufacturing permanent magnets from Nd-Fe-B green powder due to folding resulted from large height reduction and localized densification. Therefore, an adequate preform is necessary to reduce folding resulted from large height reduction and localized densification. Therefore, an adequate preform is necessary to reduce folding, lead magnets into almost desired final shape and get uniform densification. In this paper, preform design for TP is carried out without a deformable tube to investigate the behaviour of magnet sinter-forging. Preform design is accomplished to increase the effective magnet area with a near net shape and uniform densification.

• 한국정밀공학회지
• /
• 제19권1호
• /
• pp.180-185
• /
• 2002

Aluminum casting/forging process is used to produce an aluminum tie-rod end for the steering system of automobiles. Firstly, casting experiments were carried out to get a good preform for forging the tie-rod end. In the casting experiment, the effects of additives, Ti+B, Zr, Sr, and Mg, on the mechanical properties and the microstructure of a cast preform were investigated. And a finite element analysis was performed to determine an optimal configuration of the cast preform. Lastly, a forging experiment was carried out to make the final product of aluminum tie-rod end by using the above cast preform. In the casting experiments, when 0.2% Ti+B and 0.25% Zr were simultaneously added into molten Al-Si alloy, the highest values of tensile strength and elongation of the cast preform were obtained. When 0.04% Sr were added into the molten aluminum alloy, the finest silicon-structure was observed in the cast preform. The highest hardness was obtained when 0.2% Mg was added. In the forging experiment, It was confirmed that the optimal configuration of a cast preform predicted by FE analysis was very useful. The hardness of a cast/forged product using designed preform was superior to that of required specification.

• 한국주조공학회지
• /
• 제19권6호
• /
• pp.493-500
• /
• 1999

Squeeze casting was used for fabricating a light metal base composite having high strength and wearresistance. Reactive sintering was used to prepare the preform of Squeeze casting. To utilize Fe-Al intermetallic compounds and SiC particle as a reinforcement, there needs to prepare Fe-Al mixed powder at 50, 60, 70at.%Al, and add SiC powder to the above mixture at 4, 7, 16, 24wt.%. The prepared mixture with SiC was reactive sintered in a tube furnace at $660^{\circ}C$ to get a porous hybrid preform of intermetallic compound and SiC. The preform prepared above was placed in a metal mold, preheated at $660^{\circ}C$ AC4C matrix was injected into the mold with the temperature of the melt at $610^{\circ}C$ After these processes, 66MPa was applied to the mold for 5 minute to finish the whole procedure. The maximum reaction temperature was increased with the increased Al amount, but decreased with the increased SiC amount. The density of the preform was decreased with SiC amount increase in the compacts due to swelling of the preform. An optical microscope was applied to observe the micro structure and the dispersion of the reinforcements. To analyze phases, We utilized XRD, EDS. Hardness test were chosen to get the information of mechanical properties. There were no significant changes in micro structure between the composite and preform. However, it was shown that uniform dispersion of the reinforcers and complete infiltration of the melt into the preform were achieved through the procedure of the squeeze casting. It was observed that the hardness of the composite is decreased with increased SiC amount, resulting from the volumetric expansion of the preform.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.53-59
• /
• 2000

In this study aluminum casting experiments are carried out to reduce the grain size of a cast preform and to spheriodize its dendritic structure by adding Ti+B and Zr and to modify flaked eutectic silicon by adding Sr, And a finite element simulation is performed to determine an optimal configuration of the cast preform to be used in forging of a compressor piston for an automobile air-conditioner. When 0.15% Ti+B Zr and 0.05% Sr are added respectively into the molten aluminum alloy the finest grain in casting of the preform is obtained. It is confirmed that the optimal configuration of the cast preform predicted by FEM simulation is very useful for forging the compressor piston. After forging the cast preform of the compressor piston. the microstructure and the hardness of the cast preform is compared with those of the cast/forged product.

• 한국음향학회지
• /
• 제28권8호
• /
• pp.796-805
• /
• 2009

본 논문에서는 분말사출성형공정 (PIM)을 이용하여 1-3형 압전복합체용 PZT 프리폼 (preform)의 제조에 대한 연구를 수행하였다. PZT 분말을 이용해 제조한 피드스탁 (feedstock)의 점도 및 PVT 특성을 측정하였다. 또한 상용 프로그램인 3D-Timon 프로그램을 이용하여 PIM 제조공정 중 사출 성형체의 충진패턴 온도, 압력분포 및 성형 결함 등을 분석하고, 금형 시스템 및 제조공정을 최적화하였다. 최적화된 PIM 제조공정 조건을 사용하여 PZT rod가 균일하게 분포된 1-3형 압전복합체용 PZT 프리폼을 제조할 수 있었다.