• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.107-116
• /
• 1993

In the design and operation of robitic arm with flexible links, the equation of motion are required to exactly model the interaction between rigid body motion and elastic motion and to be formulated efficientlyl. In this paper, the flexible link is represented by applying the D-H rigid link representation method to measure the elestic deformation. And the equations of motion of robotic arm, which are configured by the generalized coordinates of elastic and rigid degrees of freedom, are formulated from the principle of virtual power. Dynamic characteristics due to elastic deformation of each link are obtained by using F. E. M to model complex shaped link acurately and by eliminating elastic modes of higher order that do not largely affect motion to reduce the number of elastic degrees of freedom. Also presented is the result of simulation of flexible robotic arms whose joints are controlled by direct or PD control.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1093-1098
• /
• 2003

In this paper, a practical methodology of hand-manipulator motion coordination for indoor service robot is introduced. This paper describes the procedures of opening door performed by service robot as a noticeable example of motion coordination. This paper presents well-structured framework for hand-manipulator motion coordination, which includes intelligent sensor data interpretation, object shape estimation, optimal grasping, on-line motion planning and behavior-based task execution. This proposed approach is focused on how to integrate the respective functions in harmony and enable the robot to complete its operation under the limitation of usable resources. As a practical example of implementation, the successful experimental results in opening door whose geometric parameters are unknown beforehand are provided.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.63-70
• /
• 2010

We developed a new punching system that generates pinholes expressing texts or images on a plastic plate. The pin-holed plate is used as a new glamorous display board reflecting colorful lights from the light emitting diode (LED) installed on the edge side of the plate. The four degree-of-freedom punching system was designed to make same multiple holes on four plastic plates simultaneously. For this motion, we designed a structure for a simultaneous motion of the system. For even reflection of the lights from texts or images on the board and fast production of the pin-holed boards, fast motion including precise position control is very important. We also built a PC-based integrated control system including a GUI program to help users easily design luminous texts or images on the plastic plate. Also, we conducted a performance test of the system to verify the punching speed and position control of the pin holes on the plate.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.97-103
• /
• 2001

Accuracy of a machined part is determined by the relative motion between the cutting tool and the workpiece. One of the important factors which affects the relative motion is the geometric errors of a machine tool. In this study, firstly, geometric errors are measured by laser interferometer, and the positioning error of each control point selected uniformly on the control surface CAD model can be estimated from th oirm shaping model and geometric error data base. Where a form shaping function is derived from the link of homogeneous transformation matrix. Secondly, control points are shifted to the estimated amount of positioning errors. A new control surface is modeled with NURBS(Non Uniform Rational B-Spline) surface approximation to the shifted control points. By generating tool paths to the redesigned control surface, we reduce the machining error quite.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.1
• /
• pp.40-45
• /
• 2004

This paper presents the parallel distributed control scheme for shaping of the bent glass. The designed system consists of a PC, a main controller and 11 servo-controllers, the precision motion controllers. Each elements are connected by using RS-232C and 8-bit data bus. In order to guarantee the stability and the control performance, we use a precision PID motion controller and a H-bridge on the servo-drivers. PC calculates position values of 11 DC motors by using the pre-determined curvature value and offers the user interface environment operator. The main controller provides the control instructions and parameter values to 11 servo-controllers by chip enable signal, simultaneously. Using the received commands and parameter values, the servo-controllers control the positions of the DC motors based on PID control scheme.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.1
• /
• pp.101-107
• /
• 2010

This paper presents motion control of the precision stage composed of the piezoelectric actuator and flexible hinges. The stage shows approximately 27% overshoot when the stage was applied to 30V square wave input voltage. Also, the stage shows nonlinear response characteristics including hysteresis. This paper proposes feedback control technique to suppress the phenomenon of hysteresis and overshoot using the sliding mode control scheme with the integrator. Also, this paper suggests the method that searches important parameters of sliding mode control and observer using Genetic Algorithm. To demonstrate the effectiveness of the proposed control algorithm, experimental validations are performed.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.4
• /
• pp.368-374
• /
• 2013

Maintenance works for current high-rise buildings significantly depend on human labor, unlike other construction processes that are gradually being automated. Herein, this paper proposes robotic building maintenance system using motion control, in specific, reducing a system jerk which is directly subjected to improve the process performance and economic feasibility. The sensor for detecting straight and curvature section of the building facade, moreover rail-joint segment can be detected and be utilized for reducing jerk of the system. Analysis of the proposed system error caused by excessive vibration, e.g. jerk motion is introduced. To enhance the stability and safety of the system, herein, the strategy is proposed for enhancing the performance of the system based on anti-jerk motion control algorithm which comes out increasing the stability and sustainability of the integrated system, as well.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.7
• /
• pp.862-871
• /
• 2003

In this paper, we addressed a modeling for the magnetic levitation stage. This planar magnetic levitator employs four permanent magnet liner motors. Each motor generates vertical force for suspension against gravity, as well as horizontal force for propulsion. Therefore. this stage can generate six degrees of freedom motion by the combination of forces. We derived a mechanical dynamics equation using Lagrangian method and electromechanical dynamics equation by using Co-energy method. Based on the derived dynamics, we can analyze the stage motion that is subject to the input currents and forces.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.5
• /
• pp.455-460
• /
• 1997

This paper presents a recoil and counter recoil motion measurement method using linear variable differential transformers(LVDT). The output of a LVDT is obtained from the differential voltage of the 2nd transformers. As the sensor core is attached to the motion body, the output is directly proportional to the core motion. Displacement, velocity and acceleration are measured from the core length. A comparison between the measurement result and the known value, which is obtained by the precision steel tape, shows that the accuracy and the usefulness of the proposed scheme is validated.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.10
• /
• pp.1012-1017
• /
• 2006

By breaking the symmetry of the velocity profile in the S-curve, we developed a fast starting and smooth ending motion profile, named asymmetric S-curve(AS-curve). The problem for generating motion profile is formulated, and the algorithm for the AS-curve is derived and the flow chart of the AS-curve is illustrated. By various simulations, the derived algorithm is tested and shows the validity. This AS-curve can be applied to the high precision machines where fast and vibrationless motion is required in the near future.