• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.679-682
• /
• 2004

$SrGa_2S_4$:Eu green phosphor and SrS:Eu red phosphor have been synthesized by co-precipitation method, respectively. Two sulfide phosphors were influenced by oxygen defect in host materials. Excitation spectra of these phosphors have high efficiency at the long wavelength region. And emission efficiency is increased under the excitation wavelength of 465nm. The combination of thiogallate green phosphor and sulfide red phosphor based on blue light InGaN chip has made it possible to emit white light.

• Journal of the Korean Magnetics Society
• /
• v.8 no.2
• /
• pp.93-98
• /
• 1998

Magnetic fluids have been used in the commercial area, e. g damping, sealing and hydrodynamic bearing. In this study, magnetic fluid was made for damping in loudspeaker. The magnetic fluids were snthesized by dispersing the magnetite powder which was obtained by precipitation method in Yubase oil. When the magnetic fluid was applied to a 6 cm tweeter, improvements of damping, centering and heat transger in a loudspeaker were noted. Also we compared the performance of the magnetic fluid with 20 % magnetite in the oil and the one of APG-815 (Niphon Ferrofluidic Co.)

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.171-178
• /
• 1989

In order to develope hydroxyapatite ceramics which has mechanical strength as bio-implant materials and get the basic data for the study and application of biocompatibility, hydroxyapatite was synthesized at Ca/P=1.67~1.75, pH 7~11 by precipitation method. Using prepared powders, the sintered body, fluorine substituted body and the porous body was formed and their properties were investigated. The sample obtained in condition of Ca/P=1.67, pH 7 and sintering at 1,15$0^{\circ}C$ was decomposed to $\beta$-tricalcium phosphate, and co-existed with hydroxyapatite. Hydroxyapatite synthesized at pH 11 was not easily decomposed to $\beta$-tricalcium phosphate at sintering process. The substitution of a small amount of fluorine for hydroxyapatite prevented hydroxyapatite from being decompsed to $\beta$-tricalcium phosphate. Hydroxyapatite ceramics which substited of 10% fluorine was prepared at 1,15$0^{\circ}C$, and the valueof bending strength for this body were found to be 112MPa.

• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.718-724
• /
• 2018

In this study, the $Ni_{0.9}Co_{0.05}Ti_{0.05}(OH)_2$ precursor was prepared by the concentration gradient co-precipitation method. In order to overcome the structural change due to oxygen desorption in the cathode active material with high nickel content, the physical and electrochemical analysis of the cathode active material according to the calcination temperature were investigated. Physical properties of $Li_{1.05}Ni_{0.9}Co_{0.05}Ti_{0.05}O_2$ were analyzed by FE-SEM, XRD and TGA. The electrochemical performance of the coin cell using a cathode active material and $LiPF_6$(EC:EMC=1:2 vol%) electrolyte was evaluated by the initial charge/discharge efficiency, cycle retention, and rate capabilities. As a result, the initial capacity and initial efficiency of cathode materials were excellent with 244.5~247.9 mAh/g and 84.2~85.8% at the calcination temperature range of $750{\sim}760^{\circ}C$. Also, the capacity retention exhibited high stability of 97.8~99.1% after 50cycles.

• Proceedings of the Korean Society for Applied Microbiology Conference
• /
• 2000.04a
• /
• pp.53-60
• /
• 2000

Strain BH5 was isolated from naturally fermented Kimchi and identified as a bacteriocin producer, which has bactericidal activity against Micrococcus flavus ATCC 10240. Strain BH5 was identified tentatively as Lactococcus lactis by the API test and some characteristics. Lactococcus lactis BH5 showed a broad spectrum of activity against most of the non-pathogenic and pathogenic microorganisms tested by the modified deferred method. The activity of lacticin BH5, named tentatively as the bacteriocin produced by Lactococcus lactis BH5, was detected at the mid-log growth phase, reached its maximum during the early stationary phase, and decreased after the late stationary phase. Lacticin BH5 also showed a relatively broad spectrum of activity against non-pathogenic and pathogenic microorganisms as tested by the spot-on-lawn method. Its antimicrobial activity on sensitive indicator cells was completely disappeared by protease XIV or ${\alpha}$-chymotrypsin. The inhibitory activities of lacticin BH5 were detected during treatments up to 100$^{\circ}C$ for 30 min. Lacticin BH5 was very stable over a pH range of 2.0 to 9.0 and was stable with all the organic solvents examined. The cell concentration and bacteriocin production in strain BH5 were maximum when grown at 30$^{\circ}C$ in a modified MRS medium supplemented with 0.5% tryptone, 1.0% yeast extract, and 0.5% beef extract as nitrogen sources. It demonstrated a typical bactericidal mode of inhibition against Micrococcus flavus ATCC 10240. Lacticin BH5 was purified through ammonium sulfate precipitation, ethanol precipitation, and CM-Sepharose column chromatography. The apparent molecular mass of lacticin BH5 was estimated to be in the region of 3.7 kDa, by the direct detection of bactericidal activity after SDS-PAGE. Mutant strain NO141 which was isolated by nitrosoguanidine mutagenesis produced about 4 fold more bacteriocin than the wild type.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.620-625
• /
• 2012

A general synthetic method to make $Fe_3O_{4-{\delta}}$ (activated magnetite) is the reduction of $Fe_3O_4$ by $H_2$ atmosphere. However, this process has an explosion risk. Therefore, we studied the process of synthesis of $Fe_3O_{4-{\delta}}$ depending on heat-treatment conditions using $FeC_2O_4{\cdot}2H_2O$ in Ar atmosphere. The thermal decomposition characteristics of $FeC_2O_4{\cdot}2H_2O$ and the ${\delta}$-value of $Fe_3O_{4-{\delta}}$ were analyzed with TG/DTA in Ar atmosphere. ${\beta}-FeC_2O_4{\cdot}2H_2O$ was synthesized by precipitation method using $FeSO_4{\cdot}7H_2O$ and $(NH_4)_2C_2O_4{\cdot}H_2O$. The concentration of the solution was 0.1 M and the equivalent ratio was 1.0. ${\beta}-FeC_2O_4{\cdot}2H_2O$ was decomposed to $H_2O$ and $FeC_2O$4 from $150^{\circ}C$ to $200^{\circ}C$. $FeC_2O4$ was decomposed to CO, $CO_2$, and $Fe_3O_4$ from $200^{\circ}C$ to $250^{\circ}C$. Single phase $Fe_3O_4$ was formed by the decomposition of ${\beta}-FeC_2O_4{\cdot}2H_2O$ in Ar atmosphere. However, $Fe_3C$, Fe and $Fe_4N$ were formed as minor phases when ${\beta}-FeC_2O_4{\cdot}2H_2O$ was decomposed in $N_2$ atmosphere. Then, $Fe_3O_4$ was reduced to $Fe_3O_{4-{\delta}}$ by decomposion of CO. The reduction of $Fe_3O_4$ to $Fe_3O_{4-{\delta}}$ progressed from $320^{\circ}C$ to $400^{\circ}C$; the reaction was exothermic. The degree of exothermal reaction was varied with heat treatment temperature, heating rate, Ar flow rate, and holding time. The ${\delta}$-value of $Fe_3O_{4-{\delta}}$ was greatly influenced by the heat treatment temperature and the heating rate. However, Ar flow rate and holding time had a minor effect on ${\delta}$-value.

• Resources Recycling
• /
• v.19 no.6
• /
• pp.51-60
• /
• 2010

A study on the recovery of cobalt and lithium from Lithium Ion Battery(LIB) scraps has been carried out by a physical treatment - leaching - solvent extraction process. The cathode scraps of LIB in production were used as a material of this experiment. The best condition for recovering cobalt from the anode scraps was acquired in each process. The cathode scraps are dissolved in 2M sulfuric acid solution with hydrogen peroxide at $95^{\circ}C$, 700 rpm. The cobalt is concentrated from the leaching solution by means of a solvent extraction circuit with bis(2-ethylhexyl) phosphoric acid(D2EHPA) and PC88A in kerosene, and then cobalt and lithium are recovered as cobalt hydroxide and lithium carbonate by precipitation technology. The purity of cobalt oxide powder was over 99.98% and the average particle size after milling was about 10 lim. The over all recoveries are over 95% for cobalt and lithium. The pilot test of mechanical separation was carried out for the recovery of cobalt from the scraps. The $Co_3O_4$ powder was made by the heat treatment of $Co(OH)_2$ and the average particle size was about 10 ${\mu}m$ after grinding. The recovery was over 99% for cobalt and lithium each other and the purity of cobalt oxide was over 99.98%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.351-354
• /
• 1998

The formation of the $YBa_2Cu_30_{7_\delta}$(Y123) thick films has been investigated by a surface diffusion Imcess between $3BaCu0_2$+2CuO composite coating powder and a $Y_2BaCuO_5$(Y211). This reaction has been studied in the temperature of $930^{\circ}C$ and $940^{\circ}C$ for 2h to 10h in an oxygen atmosphere. The Y211 substrates becomes covered by co-precipitation of Y123 grains and CuO inclusions. X-ray diflractotnctn. revealed that the lager consisted of an orthorhombic crystal structure. The maximum Jc of $400A/\textrm{cm}^2$ is abtained when the specimen was heat-treated at $930^{\circ}C$ for 6h on the Y211 substrate.

• Economic and Environmental Geology
• /
• v.56 no.3
• /
• pp.311-330
• /
• 2023

Development of Carbon Capture and Storage (CCS) technique is becoming increasingly important as a method to mitigate the strengthening effects of global warming, generated from the unprecedented increase in released anthropogenic CO₂. In the recent years, the characteristics of basaltic rocks (i.e., large volume, high reactivity and surplus of cation components) have been recognized to be potentially favorable in facilitation of CCS; based on this, research on utilization of basaltic formations for underground CO₂ storage is currently ongoing in various fields. This study investigated the feasibility of underground storage of CO₂ in basalt, based on the examination of the CO₂ storage mechanisms in subsurface, assessment of basalt characteristics, and review of the global research on basaltic CO₂ storage. The global research examined were classified into experimental/modeling/field demonstration, based on the methods utilized. Experimental conditions used in research demonstrated temperatures ranging from 20 to 250 ℃, pressure ranging from 0.1 to 30 MPa, and the rock-fluid reaction time ranging from several hours to four years. Modeling research on basalt involved construction of models similar to the potential storage sites, with examination of changes in fluid dynamics and geochemical factors before and after CO₂-fluid injection. The investigation demonstrated that basalt has large potential for CO₂ storage, along with capacity for rapid mineralization reactions; these factors lessens the environmental constraints (i.e., temperature, pressure, and geological structures) generally required for CO₂ storage. The success of major field demonstration projects, the CarbFix project and the Wallula project, indicate that basalt is promising geological formation to facilitate CCS. However, usage of basalt as storage formation requires additional conditions which must be carefully considered - mineralization mechanism can vary significantly depending on factors such as the basalt composition and injection zone properties: for instance, precipitation of carbonate and silicate minerals can reduce the injectivity into the formation. In addition, there is a risk of polluting the subsurface environment due to the combination of pressure increase and induced rock-CO₂-fluid reactions upon injection. As dissolution of CO₂ into fluids is required prior to injection, monitoring techniques different from conventional methods are needed. Hence, in order to facilitate efficient and stable underground storage of CO₂ in basalt, it is necessary to select a suitable storage formation, accumulate various database of the field, and conduct systematic research utilizing experiments/modeling/field studies to develop comprehensive understanding of the potential storage site.

• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.406-412
• /
• 2020

SrMoO₄:RE³⁺ (RE=Dy, Sm, Tb, Eu, Dy/Sm) phosphors are prepared by co-precipitation method. The effects of the type and the molar ratio of activator ions on the structural, morphological, and optical properties of the phosphor particles are investigated. X-ray diffraction data reveal that all the phosphors have a tetragonal system with a main (112) diffraction peak. The emission spectra of the SrMoO₄ phosphors doped with several activator ions indicate different multicolor emissions: strong yellow-emitting light at 573 nm for Dy³⁺, red light at 643 nm for Sm³⁺, green light at 545 nm for Tb³⁺, and reddish orange light at 614 nm for Eu³⁺ activator ions. The Dy³⁺ singly-doped SrMoO₄ phosphor shows two dominant emission peaks at 479 and 573 nm corresponding to the ⁴F_9/2→⁶H_15/2 magnetic dipole transition and ⁴F_9/2→⁶H_13/2 electric dipole transition, respectively. For Dy³⁺ and Sm³⁺ doubly-doped SrMoO₄ phosphors, two kinds of emission peaks are observed. The two emission peaks at 479 and 573 nm are attributed to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions of Dy³⁺ and two emission bands centered at 599 and 643 nm are ascribed to ⁴G_5/2→⁶H_7/2 and ⁴G_5/2→⁶H_9/2 transitions of Sm³⁺. As the concentration of Sm³⁺ increases from 1 to 5 mol%, the intensities of the emission bands of Dy³⁺ gradually decrease; those of Sm³⁺ slowly increase and reach maxima at 5 mol% of Sm³⁺ ions, and then rapidly decrease with increasing molar ratio of Sm³⁺ ions due to the concentration quenching effect. Fluorescent security inks based on as-prepared phosphors are synthesized and designed to demonstrate an anti-counterfeiting application.