• 환경위생공학
• /
• 제10권2호
• /
• pp.1-12
• /
• 1995

Under accelerated industrial developments environment pollution comes out to be very stirious. Especially the ions of heavy metal from wastewater, even if they are minimal, accumulated in ecology circle and do finally injury to human health. The general process for removal of heavy metals include coagulation and following sedimentation, ion -exchange and active carbon adsorption and sedimentation that applicate in popular, needs the expense of coagulant the additional treatment of sludge on the general process of coagulation and sedimentation. It is also a serious problem that the second pollution caused by coagulant. However chelating adsorption that uses natural chelating high- molecular compound has not pollution problem Among chelating high- molecules, the diminishing chitin that contained in crustaceans as crawfish and crab in our country with affluent water resources are easy to get. So it is advantageous to use this ubiquitous material for removing heavy metals because we could reuse natural resource. In this research, the author tested the effectiveness of the adsorption and removal of heavy metal ions by chitin and its derivatives. Chitin and cellulose became beads and used as flocculant, in this test. The results are as follows . First, bead showed higher removal ratio than powder in the comparative test on adsorbents such as chitin, chitosan and cellulose. Secondly, in the variety test by the kinds of adsorbent and time. chitosan bead and cellulose bead that showed the highest removal ratio. One hour need to remove the ions of heavy metal. Thirdly, the results of the adsorption degree test by pH revealed high removal ratio adsorption of chitin, cellulose and chitosan bead in alkalin condition but chitosan bead in acidic condition.

• 한국표면공학회지
• /
• 제45권6호
• /
• pp.248-256
• /
• 2012

A Pd-based hydrogen membranes for hydrogen purification and separation need high hydrogen perm-selectivity. The surface roughness of the support is important to coat the pinholes free and thin-film membrane over it. Also, The pinholes drastically decreased the hydrogen perm-selectivity of the Pd-based composite membrane. In order to remove the pinholes, we introduced various surface pre-treatment such as alumina powder packing, nickel electro-plating and micro-polishing pre-treatment. Especially, the micro-polishing pretreatment was very effective in roughness leveling off the surface of the porous nickel support, and it almost completely plugged the pores. Fine Ni particles filled surface pinholes with could form open structure at the interface of Pd alloy coating and Ni support by their diffusion to the membrane and resintering. In this study, a $4{\mu}m$ surface pore-free Pd-Cu-Ni ternary alloy membrane on a porous nickel substrate was successfully prepared by micro-polishing, high temperature sputtering and Cu-reflow process. And $H_2$ permeation and $N_2$ leak tests showed that the Pd-Cu-Ni ternary alloy hydrogen membrane achieved both high permeability of $13.2ml{\cdot}cm^{-2}{\cdot}min^{-1}{\cdot}atm^{-1}$ permation flux and infinite selectivity.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.129-129
• /
• 2018

Hard coating application is effective way of cutting tool for hard-to-machine materials such as Inconel, Ti and composite materials focused on high-tech industries which are widely employed in aerospace, automobile and the medical device industry also Information Technology. In cutting tool for hard-to-machine materials, high hardness is one of necessary condition along with high temperature stability and wear resistance. In recent years, high-entropy alloys (HEAs) which consist of five or more principal elements having an equi-atomic percentage were reported by Yeh. The main features of novel HEAs reveal thermodynamically stable, high strength, corrosion resistance and wear resistance by four characteristic features called high entropy, sluggish diffusion, several-lattice distortion and cocktail effect. It can be possible to significantly extend the field of application such as cutting tool for difficult-to-machine materials in extreme conditions. Base on this understanding, surface coatings using HEAs more recently have been developed with considerable interest due to their useful properties such as high hardness and phase transformation stability of high temperature. In present study, the nanocomposite coating layers with high hardness on WC substrate are investigated using high entropy alloy target made a powder metallurgy. Among the many surface coating methods, reactive magnetron sputtering is considered to be a proper process because of homogeneity of microstructure, improvement of productivity and simplicity of independent control for several critical deposition parameters. The N2 is applied to reactive gas to make nitride system with transition metals which is much harder than only alloy systems. The acceleration voltage from 100W to 300W is controlled by direct current power with various deposition times. The coating layers are systemically investigated by structural identification (XRD), evaluation of microstructure (FE-SEM, TEM) and mechanical properties (Nano-indenter).

• 공업화학
• /
• 제24권6호
• /
• pp.611-615
• /
• 2013

본 연구에서는 바나듐 산화물($VO_2$)과 텅스텐이 도핑된 바나듐 산화물(W-$VO_2$) 분말을 바나듐 산화물($V_2O_5$)과 옥살산수화물로부터 수열합성과 하소공정을 통하여 성공적으로 제조하였다. 시료들의 결정구조와 열변색 특성들은 FE-SEM, XRD, XPS, DSC 및 UV-Vis-NIR 분광기를 이용하여 분석하였다. W-$VO_2$ 시료에 W의 도핑량을 증가시키면, W-$VO_2$ 시료의 상전이 온도가 $70^{\circ}C$에서 $42^{\circ}C$로 낮아지는 경향이 있었다. 또한, W-$VO_2$ 시료를 상전이 온도 이상으로 가열시키면 UV-Vis-NIR 곡선이 가시광 영역에서는 변하지 않고 NIR 영역에서는 낮은 투과도 방향으로 이동하는 경향이 있었다.

• 한국수소및신에너지학회논문집
• /
• 제18권1호
• /
• pp.26-31
• /
• 2007

Hydrogen has a high potential to be a renewable substitute for fossil fuels, because of its high gravimetric energy density and environment friendliness. In particular, Magnesium have attracted much interest since their hydrogen capacity exceeds that of known metal hydrides. One of the approaches to improve the kinetic is addition of metal oxide. In this paper, the effect of $Fe_2O_3$ concentration on the kinetics of Mg hydrogen absorption reaction was investigated. $MgH_x-Fe_2O_3$ composites have been synthesized by hydrogen induced mechanical alloying. The powder synthesized was characterized by XRD, SEM and simultaneous TG, DSC analysis. The hydrogenation behaviors were evaluated by using a sievert's type automatic PCT apparatus. Absorption and desorption kinetics of Mg catalyzed with 5,10 mass% $Fe_2O_3$ are determined at 423, 473, 523, 573, 623K.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.479-481
• /
• 2000

The effect of $Al_{2}O_{3}+Y_{2}O_{3}$ additives on fracture toughness of $\beta-SiC-TiB_2$ composites by hot-pressed sintering were investigated. The f$\beta-SiC-TiB_2$ ceramic composites were hot-presse sintered and annealed by adding 16, 20, 24wt% $Al_{2}O_{3}+Y_{2}O_{3}$(6 : 4wt%) powder as a liquid forming additives at low temperature($1800^{\circ}C$) for 4h. In this microstructures, the relative density is over 95.88% of the theoretical density and the porosity increased with increasing $Al_{2}O_{3}+Y_{2}O_{3}$ contents because of the increasing tendency of pore formation. The fracture toughness showed the highest of $5.88MPa{\cdot}m^{1/2}$ for composites added with 20wt% $Al_{2}O_{3}+Y_{2}O_{3}$ additives at room temperature. The electrical resistivity showed the lowest of $5.22{\times}10^{-4}\Omega{\cdot}cm$ for composite added with 20wt% $Al_{2}O_{3}+Y_{2}O_{3}$ additives at room temperature and is all positive temperature coefficient resistance (PTCR) against temperature up to $700^{\circ}C$.

• 한국재료학회지
• /
• 제8권5호
• /
• pp.444-449
• /
• 1998

EMI 차폐재를 이용하여 전자파 장해를 극복하는 방법에는 금속판을 이용하는 방법과 플라스틱 표면에 전도층을 형성하는 방법, 전도성 충진제를 플라스틱에 혼입하는 방법이 대표적으로 사용되고 있으나 각각의 방법마다 장단점이 존재하기 때문에 많은 연구들의 목적은 전자 기기 본체의 무게를 증가시키지 않고 최대한 전자파 차폐 효율을 높이는 물질 개발에 목적을 두고 있다. 이러한 목적을 위하여 본 연구에서는 비중이 낮고 판상형인 운모 분체 펴면 위에 무전해 니켈 도금을 시행하므로써 전도성을 지니는 금속화운모를 제조하여, 이를 EMI차폐용 분체로서 사용하였다. 또한 이 EMI 차폐용 분체의 특성을 고찰 하였다. 미분체 운모 표면에 무전해 니켈막 금속화운모 미분체를 도료화하여 전자파 차폐 효과를 측정한 결과 최고 63dB를 나타내었다. 이 값은 구리 금속판을 이용한 전자파 차폐의 90dB에는 못 미치지만, 도포 횟수를 6회 이상 시행했을 경우 전자파 차폐 효과가 약 10dB 정도가 증가함을 알 수 있었고, 넓은 범위의 전자파 차폐 효과를 거둘 수 있는 특징이 있다.

• 한국재료학회지
• /
• 제20권8호
• /
• pp.444-449
• /
• 2010

Transparent ceramics are used in new technology because of their excellent mechanical properties over glasses. Transparent ceramics are nowadays widely used in armor, laser windows, and in high temperature applications. Silicon nitride ceramics have excellent mechanical properties and if transparent silicon nitride is fabricated, it can be widely used. h-BN has a lubricating property and is ductile. Therefore, adding h-BN to silicon nitride ceramics gives a lubricating property and is also machinable. Translucent silicon nitride was fabricated by hot-press sintering (HPS) and 57% transmittance was observed in the near infrared region. A higher wt. % of h-BN in silicon nitride ceramics does not favor transparency. The optical, mechanical, and tribological properties of BN dispersed polycrystalline $Si_3N_4$ ceramics were affected by the density, ${\alpha}:{\beta}$-phase ratio, and content of h-BN in sintered ceramics. The hot pressed samples were prepared from the mixture of $\alpha-Si_3N_4$, AlN, MgO, and h-BN at $1850^{\circ}C$. The composite contained from 0.25 to 2 wt. % BN powder with sintering aids (9% AlN + 3% MgO). A maximum transmittance of 57% was achieved for the 0.25 wt. % BN doped $Si_3N_4$ ceramics. Fracture toughness increased and wear volume and the friction coefficient decreased with an increase in BN content. The properties such as transmittance, density, hardness, and flexural strength decreased with an increase in content of h-BN in silicon nitride ceramics.

• Journal of Welding and Joining
• /
• 제26권4호
• /
• pp.50-54
• /
• 2008

In this research, anode for SOFC has been manufactured from two different kinds of feedstock materials through thermal spraying process and the properties of the coatings were characterized and compared. One kind of feedstock was manufactured from spray drying method which includes nano-components of NiO, YSZ (300 nm) and graphite. And the other is manufactured by blending the micron size NiO coated graphite, YSZ and graphite powders as feedstock materials. Microstructure, mechanical properties and electrical conductivity of the coatings as-sprayed, after oxidation and after hydrogen reduction containing nano composite which is prepared from spray-dried powders were evaluated and compared with the same properties of the coatings prepared from blended powder feedstock. The coatings prepared from the spray dried powders has better properties as they provide larger triple phase boundaries for hydrogen oxidation reaction and is expected to have lower polarization loss for SOFC anode applications than that of the coatings prepared from blended feedstock. A maximum electrical conductivity of 651 S/cm at $800^{\circ}C$ was achieved for the coatings from spray dried powders which much more than that of the average value.

• 한국건설순환자원학회논문집
• /
• 제8권3호
• /
• pp.263-268
• /
• 2020

이 연구의 목적은 폐타이어 고무분말을 혼입한 폴리우레탄 복합재료와 굵은 골재를 사전채움하고 폴리우레탄을 주입한 폴리우레탄 복합재료의 감쇠성능을 평가하는 것이다. 이를 위하여 총 4 종류의 폴리우레탄 기반 복합재료를 제조하였고, 충격 가진 실험을 실시하였다. 실험을 통하여 시간 영역과 주파수 영역에서의 진동특성을 계측한 후 감쇠비를 계산하였다. 실험 결과, 고무분말을 혼입하여 폴리우레탄의 양이 각각 10.6%와 21.2% 줄어든 실험체들의 감쇠비는 순수한 폴리우레탄 실험체에 비하여 각각 8.4%와 4.6% 낮은 것으로 나타났다. 프리팩트 콘크리트 제조 방법과 유사한 방법으로 제조한 폴리우레탄 복합재료의 감쇠비는 순수 폴리우레탄에 비하여 22% 낮은 것으로 나타났지만 폴리우레탄 혼입량은 50% 감소하였으며, 강성은 25.7배 높은 것으로 나타났다.