• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.566-574
• /
• 2012

Porous zirconia ceramics are widely considered to be important due to their unique properties and potential applications. In this paper, we propose a novel approach to produce porous zirconia ceramics. The linear shrinkage of the prepared porous zirconia ceramics could be controlled to 4% by incorporating pre-sintered zirconia granules and hollow polymeric spheres. We also investigated the effect of pre-sintered zirconia granules on the microstructure and the properties, such as the porosity, pore distribution, and bending strength of the porous zirconia ceramics.

• Korean Journal of Materials Research
• /
• v.20 no.3
• /
• pp.155-160
• /
• 2010

In this study, we investigated primary biocompatibility and osteogenic gene expression of porous granular BCP bone substitutes with or without strontium (Sr) doping. In vitro biocompatibility was investigated on fibroblasts like L929 cells and osteoblasts like MG-63 cells using a cell viability assay (MTT) and one cell morphological observation by SEM, respectively. MTT results showed a cell viability percent of L929 fibroblasts, which was higher in Sr-BCP granules (98-101%) than in the non-doped granules (92-96%, p < 0.05). Osteoblasts like MG-63 cells were also found to proliferate better on Sr-doped BCP granules (01-111%) than on the non-doped ones (92-99%, p < 0.05) using an MTT assay. As compared with pure BCP granules, SEM images of MG-63 cells grown on sample surfaces confirmed that cellular spreading, adhesion and proliferation were facilitated by Sr doping on BCP. Active filopodial growth of MG-63 cells was also observed on Sr-doped BCP granules. The cells on Sr-doped BCP granules were well attached and spread out. Gene expression of osteonectin, osteopontin and osteoprotegrin were also evaluated using reverse transcriptase polymerase chain reaction (RT-PCR), which showed that the mRNA phenotypes of these genes were well maintained and expressed in Sr-doped BCP granules. These results suggest that Sr doping in a porous BCP granule can potentially enhance the biocompatibility and bone ingrowth capability of BCP biomaterials.

• Journal of the Korean Ceramic Society
• /
• v.54 no.2
• /
• pp.108-113
• /
• 2017

The use of aluminum-based coagulants in water pretreatment is being carefully considered because aluminum exposure is a risk factor for the onset of Alzheimer's disease. Lightly burned-dolomite kiln dust (LB-DKD) was evaluated as an alternative coagulant because it contains high levels of the healthful minerals calcium and magnesium. An organic pore forming agent (OPFA) was incorporated to prepare porous granules after OPFA removal through a thermal decomposition process. A spray drying method was used to produce uniform and reproducible spherical granules with low density, since fine dolomite particles have irregular agglomeration behavior in the hydration reaction. The use of fine dolomite powder and different porosity granules led to a visible color change in raw algae (RA) containing water, from dark green to transparent colorlessness. Also, dolomite powders and granules exhibited a mean removal efficiency of 48.3% in total nitrogen (T-N), a gradual increase in the removal efficiency of total phosphorus (T-P) as granule porosity increased. We demonstrate that porous dolomite granules can improve the settling time and water quality in summer seasons for the emergent treatment of excessive algal blooms in eutrophic water.

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.113-119
• /
• 1995

The green body was fabricated by a new forming method, pressureless powder packaing forming method, and the characteristics of sintered specimen were investigated. It was found that alumina ceramics prepared by the present method showed porous structure with narrow pore size distribution, and in case of abrasive powder sintered body, compared with dry-pressed specimen, had the nearly same density. Especially, the specimen prepared with spray-dried granules showed the characteristic that granules were not either deformed or fractured during forming and sintering process. Therefore, it was found that this new forming method was effective method in fabrication of porous ceramics on account of easy control of porosity and pore size and its high thermal stability.

• Archives of Pharmacal Research
• /
• v.2 no.1
• /
• pp.17-24
• /
• 1979

A first systematic approach on new and simple preparation method of spherical granules in the system using organic granulating solution was carried out. Mixer granulation required narrow range of moisture content but gentle action of tumbling in the mixer and capilary forces were adequate to compact the porous mass and also were highly effective to produce granules close to sphere. Where the granules by massing and screening provided the more open structure, its pore distribution lied between 71 and 16 .mu.m by above 50% and on the contrary, that of the mixer granulated granules showed only below 25%. Increase in retention time in the mixer decreased the intragranular porosity of granules produced, and in comparison with granular particles produced by conventional wet granulation, those from the mixer granulation had the advantages of flow properties, packing characteristics and definite spherocity. They also had extremely low friability resulting in few fines.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.11a
• /
• pp.40.2-40.2
• /
• 2008

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.251-255
• /
• 2014

In this study, we optimized dissolution the dissolution conditions of porous amorphous powder to have high specific surface area. Porous metallic glass(MG) granules were fabricated by selective phase dissolution, in which brass is removed from a composite powder consisting of MG and 40 vol.% brass. Dissolution was achieved through various concentrations of $H_2SO_4$ and $HNO_3$, with $HNO_3$ proving to have the faster reaction kinetics. Porous powders were analyzed by differential scanning calorimetry to observe crystallization behavior. The Microstructure of milled powder and dissolved powder was analyzed by scanning electron microscope. To check for residual in the dissolved powder after dissolution, energy dispersive X-ray spectroscory and elemental mapping was conducted. It was confirmed that the MG/brass composite powder dissolved in 10% $HNO_3$ produced a porous MG granule with a relatively high specific surface area of $19.60m^2/g$. This proved to be the optimum dissolution condition in which both a porous internal granule structure and amorphous phase were maintained. Consequently, porous MG granules were effectively fabricated and applications of such structures can be expanded.

• Applied Chemistry for Engineering
• /
• v.18 no.2
• /
• pp.111-115
• /
• 2007

Bimodally porous ${\gamma}$-alumina granules, including mesopores (2~50 nm) and macropores (>50 nm), were prepared by sol-gel and oil-drop method. Mesopores are made from the voids among the alumina crystallites, while macropores are from the space of the decomposed PS particles used as physical templates during the granulation process. The product ${\gamma}$-alumina granules with the average diameter of 2 mm were characterized by FE-SEM, XRD, FT-IR, $N_2$ porosimetry, and universal mechanical testing system.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.54.2-54.2
• /
• 2011

DTBP (dimethyl 3,3`-dithiobispropionimidate) was applied to collagen and gelatin coating on BCP granules and a crosslinking agent. The DTBP crosslinking was done for decreasing the solubility of the coating and hence increasing the stability. The nanostructure of collagen and gelatin coating surfaces were observed by SEM technique. Based on the DSC thermograms and FT-IR spectrums, the crosslinkings were confirmed between collagen molecules and gelatin molecules. The compressive strength was measured before crosslinking and after that. In-vitro study was carried out by measuring cell viability and observing cell morphology after DTBP crosslinking. Moreover, the proliferation ability of MG-63 osteoblast-like cells on the crosslinked BCP granules was evaluated by Western blot assay. The BCP granules were implanted into rabbit femur for 4 weeks and 12 weeks. The bone tissue formation was analyzed with micro-computed tomography (micro-CT) and histological analysis was also carried out by hematoxylin and eosin (H&E) staining for visualization of cells.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.130-131
• /
• 2020

This study manufactured the porous foamed concrete granules coated with TiO₂ Nanoparticles, to widen the specific surface area. The Removal rate of concrete granules coated with TiO₂ Nanoparticles was average 56.7%, which was approximately 2.3 time higher than that of the conventional surface TiO₂ coating.