• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 12th Asian Congress of Fluid Mechanics
• /
• pp.48.2-48.2
• /
• 2008

• 에너지공학
• /
• 제21권4호
• /
• pp.385-392
• /
• 2012

본 연구는 현재 콘덴싱 보일러에 많이 사용하는 다공성 소재중에서 메탈화이버(metal fiber, MF) 및 세라믹(ceramic, CM)으로 제작한 평판형 버너에 대해 연소 및 열특성을 비교 검토하고 그 결과를 향후 개발할 EGR(Exhaust gas recirculation) 콘덴싱 보일러에 적용할 버너 선정의 기초자료로 활용하는 것을 목적으로 한다. CO 배출량은 CM이 MF보다 높았고 NOx 배출량은 MF가 CM보다 높게 나타났다. 버너열량 변화시에는 버너열량이 클수록 효율이 높게 나타났으며 버너 소재별 열효율은 버너열량 변화와 관계없이 MF가 CM보다 높게 나타났다. 본 실험범위에서 KS B 기준과 EN 677기준을 근거로 비례제어, 열효율, CO 및 NOx 배출량을 고려할 때 버너 소재는 MF가 적절하며 당량비는 0.8일때가 최적 운전조건으로 판단된다.

• 대한기계학회논문집B
• /
• 제31권6호
• /
• pp.539-546
• /
• 2007

An experimental study was performed to investigate the characteristics of chemiluminescence in a radiant burner, varying the excess air ratio from 0.91 to 1.67 at firing rate 80.5 to 134.2 kW/m2 on $OH^*,\;CH^*,\;{C_2}^*$ in LNG-Air premixed flames. The signals from electronically excited states of $OH^*,\;CH^*,\;{C_2}^*$ were detected using a Intensified Couple Charged Detector (ICCD) camera. The measurements of exhausted emission were made to investigate the correlation between chemiluminescence and emissions. The chemiluminescence intensity was increased with increase of firing rate like characteristics of $NO_x$ emission. $NO_x$ also increased with increase of firing rate and excess air ratio. It is found that offset of firing rate is more dominant excess air ratio $NO_x$ emission. The maximum chemiluminescence intensity occurs near the stoichiometric excess air ratio or lean conditions in case of high firing rate and the maximum intensity occurs rather than rich conditions in case of relatively low firing rate. Amount of $NO_x$ emission is maximum at near stoichiometric excess air ratio, which is chemiluminescence intensity is maximum.

• 한국연소학회지
• /
• 제18권3호
• /
• pp.24-30
• /
• 2013

Flame stabilization characteristics of premixed flames in an annular coaxial 5-tubes burner (AC5TB) were investigated experimentally. The AC5TB was made of five quartz tubes, and the flame stabilization conditions in that burner were investigated with the variation of equivalence ratio and the flow velocities. Flame behaviors inside of narrow annular tubes could be observed directly. Overall flame stabilization conditions were similar to that of the previous study, while the flame behaviors and structures were different mainly due to the controlled uniform distribution of the velocities in channels. Flame flashback conditions were thought to be governed by the competition between heat release rate, heat loss and heat recirculation in each channel. Stationary flames at a fixed location were compared in its velocity distribution and burned gas temperature across the channel. This AC5TB can be a basic configuration for the development of flame stabilization model of porous media combustors, and it will help understand about the real behavior of flames in meso-scale combustion spaces.

• 한국연소학회지
• /
• 제10권1호
• /
• pp.7-12
• /
• 2005

The surface flames in perforated ceramic burner are experimentally characterized to investigate the effects of equivalence ratio and heating rate. The results show that the surface flames are classified into green, red radiant and blue surface flame as the decrease of equivalence ratio. Each flame is maintained very stable at the specified equivalence ratio and represents the same flame characteristics at any orientation of ceramic burner. Particularly the blue surface flame is found to be very stable at very lean equivalence ratio at 7000kcal/hr to 20000kcal/hr heating rates. And the exhausted NOx measurement shows that blue surface flame represents the lowest NOx emission regardless of the location of burner since it sustains very stable at lean mixture ratio.

• 한국수소및신에너지학회논문집
• /
• 제30권5호
• /
• pp.455-464
• /
• 2019

Experiments were conducted to investigate the sensitivity of steel plate oxidation with temperature in a simulated furnace. Used steel plates were a general steel and a high tensile steel. Porous media burner (PM burner) used in model furnace was made for uniform temperature profile. The surrounding temperature was controlled by adjusting the flow rate of the mixture in the combustor. Oxide layer analysis was performed using SEM image analysis and EDS line scanning. Both steel sheets showed a tendency to increase the thickness of the steel sheet surface oxide layer as the temperature increases, and it was confirmed that the flaking phenomenon in surface oxidation layer appeared when the temperature was above a certain temperature.

• 대한기계학회논문집B
• /
• 제20권10호
• /
• pp.3243-3250
• /
• 1996

Emission characteristics of nitric oxides and carbon monoxide from a porous media combustor has been experiment studied. The relationship between the change of flame shape and emission has also been examined. As the equivalence ratio decreases, the flame shape on the ceramic matrix plate changes from a diffusion flame, R(radiant)-type flame, to B(Blue)-type flame. With large fuel flow rate, R-type flame turns to be two dimensional R-II type flame around the equivalence of 0.7. Carbon monoxide emission increases very rapid with decreasing equivalence ratio. It changes a lot from some 10 ppm to 100-10,000 ppm with the change of flame type from R-I to R-II type. Nitric oxide emission from the premixed burner is less than 25 ppm over all range of fuel flow rate, which is less than 20% of NOx emission from conventional gas burners.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.49-53
• /
• 2001

A conventional flame type gas combustion major portion of heat is transferred to the body by convection due to small radiant ability of the gas flame. Increasing the radiation component of heat flux in the combustion zone allows to augment the efficiency of gas utilization. Such effect can be reached by using radiative gas burner applied to metal mesh combustion. Basically the gas radiant burner consists of metallic mesh of high heat resisting steels. In terms of this regards, we have made the burner consisted of metal mesh and measured the radiative flame stability of natural gas/air mixture on the metal mesh burner. The pressure loss through the metal mesh is defined by pressure-velocity slope. The more increased the pressure-velocity slope of the metal mesh is, the wider the stable zone of radiave flame on the metal mesh burner is. And the augmentation of mixture flowrate through the metal mesh make narrow the permissible range of equivalence ratio.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.176-183
• /
• 2007

An experimental study was performed to investigate the effects of mixing quality, inlet pressure, nozzle diameter on CO emission and radiation characteristics in porous ceramic fiber radiant burners. Observations of combustion characteristics occurring inside the burner system which was insulated fiber mat, were investigated by measuring temperature, CO emission and radiation characteristics. Combustion was achieved at the firing rate of $88{\sim}99$ kcal/hr, inlet pressure of $100{\sim}250$mm$H_2O$. CO emissions were found to be strongly dependent on the operating conditions. There was a tendency that CO concentration increased as the firing rate increases. The reason for rise of CO concentration is that it becomes the relatively rich condition. The fiber burner exhibit significant both spectral intensity peaks in the bands at 2.5${\mu}m$ and 4.0${\mu}m$ relatively, There is a small difference in the variable mixing tube. However spectral intensity increased with the firing rate.

• 한국수소및신에너지학회논문집
• /
• 제29권5호
• /
• pp.512-522
• /
• 2018

This study was conducted to investigate on the combustion characteristic with the effects of mat thickness and fuel kinds in a metal-fiber burner. The mode transition point is confirmed by the K value, which was defined as the rate of flow velocity and laminar burning velocity. The ($T^4_{sur}-T^4_{\infty}$) is highest at methane flame with 3 T thickness. Through the measurement of the unburned mixture temperature, the possibility of submerged flame in surface combustion burner was confirmed. The rapid emission of CO occurs nearby limit blow out (LBO) because of the increase of flow velocity. In case of NOx, the trend is similar with surface temperature. However, it also considered that the NOx emission is affected by residence time with flame position.