• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.4
• /
• pp.32-41
• /
• 2002

Present study aims to investigate draft effects on hydro-elastic response of pontoon type VLFS(Very Large Floating Structure). A three dimensional higher-order boundary element method(HOBEM: Hong et al;1999, Choi, Hong and Choi; 2001) is extended to analyze elastic response of structures. Intensive numerical calculations were carried out for box type structure to investigate the draft effect on hydrodynamic forces on pontoon type VLFS. Main attention was paid to wave run-up along the waterline for various cases of draft scantling. It is found that the draft effects on the hydro-elastic response of pontoon type VLFS are important especially in short wave range and shallow water region.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.3
• /
• pp.213-217
• /
• 2007

Pontoon type very large floating structure has been considered and actively studied as one of the most important ocean space utilization. The hydroelastic displacement of the pontoon type floating structure in waves is the largest at its weather side. The purpose of this study is to investigate the characteristics and effects of the submerged horizontal plate which is developed to reduce the wave exciting forces acting on the pontoon type floating structure using numerical analysis. The numerical method based on the finite difference method has been adopted and compared with the experimental data to confirm the reliability of it. We have performed the numerical computation of wave exciting forces acting on the pontoon type floating structure with/without submerged plate and discuss the results of simulation.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.5
• /
• pp.53-59
• /
• 2003

Ocean space utilization using VLFS(Very Large Floating Structures) can provide environmental impact free space by allowing sea water flow freely through the floating structure. Use of Pontoon type VLFS for that purpose needs employment of breakwaters for reduction of wave effects. Therefore, in order to maximize advantage of environmental impact free structure, the breakwater should be the one that can allow water flow freely through it, too. In this paper hydroelastic response of a pontoon type structure is analyzed considering breakwaters which allow water flow through its opening at bottom of the breakwaters. Mode superposition technique is used for solving equation of flexible body while interactions between the pontoon and breakwaters is considered based on generalized mode concept. Bi-quadratic nine node higher-order boundary element method is adopted for more accurate numerical treatment near sharp edged body shape. Performance of various combinations of breakwaters is investigated.

• Ocean Systems Engineering
• /
• v.9 no.4
• /
• pp.423-448
• /
• 2019

Very Large Floating Structures (VLFS) are one among the solution to pursue an environmentally friendly and sustainable technology in birthing land from the sea. VLFS are extra-large in size and mostly extra-long in span. VLFS may be classified into two broad categories, namely the pontoon type and semi-submersible type. The pontoon-type VLFS is a flat box structure floating on the sea surface and suitable in regions with lower sea state. The semi-submersible VLFS has a deck raised above the sea level and supported by columns which are connected to submerged pontoons and are subjected to less wave forces. These structures are very flexible compared to other kinds of offshore structures, and its elastic deformations are more important than their rigid body motions. This paper presents hydroelastic analysis carried out on an innovative VLFS called truss pontoon Mobile Offshore Base (MOB) platform concept proposed by Srinivasan and Sundaravadivelu (2013). The truss pontoon MOB is modelled and hydroelastic analysis is carried out using HYDRAN-XR^* for regular 0° waves heading angle. Results are presented for variation of added mass and damping coefficients, diffraction and wave excitation forces, RAOs for translational, rotation and deformational modes and vertical displacement at salient sections with respect to wave periods.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.1 s.139
• /
• pp.43-49
• /
• 2005

in this paper a dolphin-fender moored pontoon-type floating structure in shallow water depth is studied focusing on mooring force. The pontoon-type floating structure is 500m long, 300m wide. The structure has partially non-uniform drafts of 2.0m and 3.0m. The employed mooring system is a guyed frame type dolphin-fender system. The 1/125 scale model fender system is made of rubber tube to have hi-linear load deflection characteristics. A series of model tests has been conducted focusing on motion and fender force responses in regular and irregular waves at KRISO's ocean engineering basin Non-linear numerical simulation of fender reaction force has been carried out and the results are compared with those of model tests. The simulated rigid body motion and mooring forces also have been compared with the test results.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.5 no.3
• /
• pp.35-44
• /
• 2002

In this paper, the analytic studies on the wave control performance of moored pontoon-type floating breakwater are presented. A two-dimensional eigenfunction expansion method is adopted to study the motion responses and the transmission coefficients of pontoon-type floating breakwater in beam waves. The stiffness coefficients of mooring line are idealized as linear elastic spring. Comparison of the analytical results with a numerical results (FEM) shows good agreement over a wide range of frequencies. The performance of mooed pontoon-type floating breakwater is tested with various design parameters such as sectional geometry, mooring line characteristics and wave frequencies. It is found that the properly designed floating breakwater can be an effective wave control structure.

• Journal of Navigation and Port Research
• /
• v.31 no.8
• /
• pp.683-687
• /
• 2007

Hydroelastic deformation of pontoon type floating structure in waves is critical in structural design. Therefore, it is necessary to develop additional technology that make to dissipate the wave energy as the submerged horizontal plate. In this study, we investigate the characteristics of hydrodynamic interaction effect by the submerged plate affecting to the radiation forces on a pontoon type floating structure using numerical analysis. We have developed the numerical method based on the composite grid system that consists of moving and fixed grid to compute the radiation forces due to the heaving motion of pontoon type floating structure and submerged plate. The numerical simulations based on the finite difference method are carried out to solve the fully nonlinear free surface involving the breaking waves and compared with the experimental data to confirm the reliability of the numerical method. Then, we discuss the interaction effects on the hydrodynamic forces that could influence on the hydroelastic response of floating structure.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6A
• /
• pp.425-433
• /
• 2011

In this study, in order to investigate the wave-induced buoyancy effects, experimental studies were conducted on pontoon-type floating structures. A series of small-scale tests with various wave cases were performed on the pontoon models. A total of four small-scale pontoon models with different lateral shapes and bottom details were fabricated and tested under the five different wave cases. Six hydraulic pressure gauges were attached to the bottom surfaces of the pontoon models and the wave-induced hydraulic pressure was measured during the tests. Finally, hydraulic pressures subjected to the bottoms of the pontoon models were compared with each other. As the results of this study, it was found that whereas the waffled bottom shape hardly influenced the wave-induced hydraulic pressure, the hybrid lateral shape significantly influenced the wave-induced hydraulic pressure subjected on the bottoms of floating structures. The air gap effects of the hybrid shape contribute to decreasing the wave-induced hydraulic pressure due to absorption of wave impact energy. Compared with box type, the hydraulic pressures of the hybrid type were about 83% at the bow, 74% at the middle, and 53% at the stern.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.36 no.4
• /
• pp.149-157
• /
• 2024

In this study, hydraulic model tests were conducted to investigate the effect of a horizontal damping plate on the motion of the pontoon-type floating structure. The floating structures with and without the horizontal damping plates were fabricated with the scale of 1/20 and their motion responses to the regular and irregular wave conditions were investigated. From the comparison for the responses of each model with 16 wave conditions, it could be known that the damping plate made the response of the the pontoon to be smaller by about 5 to 10 % compared with the normal rectangular pontoon.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.38 no.5
• /
• pp.316-322
• /
• 2005

In order to develop a floating breakwater, which can efficiently control long period waves, vertical plates are attached in pontoon. Wave control and dynamic behaviors of the newly developed vertical plates type are verified from numerical analysis and hydraulic experiment. As a result, for the wave control and energy dissipation, the newly developed vertical plates type is more efficient than the conventional pontoon type. For the floating body motion, the wave transmission, depending on incident wave period, is decreased at the natural frequency. Dimensionless drift distance has similar trend of the reflection rate of wave transformation near natural frequency except maximum and minimum values. Dimensionless maximum tension is 17 percent of the weight of floating breakwater in case of the conventional pontoon type and 18 percent or 14 percent in case of the newly developed vertical plates type. Thus, it is shown that the wave control is improved by the vertical plates type. In addition, by adjusting the interval of the front and back vertical plate, we would control proper wave control.